Tus neeg siv phau ntawv
Table Of Contents
- POC-621 Series (DC-/ AC-in model)
- Contents
- 1 General Information
- 1.1 Introduction
- 1.2 Specifications
- 1.3 Dimensions
- Figure 1.1 Dimensions of the POC-621
- Figure 1.2 POC-621 Hot Swappable Battery Pack Dimensions
- Figure 1.3 POC-621 with Smart Card Reader Dimensions
- Figure 1.4 POC-621 with RFID & Camera Accessory Dimensions
- Figure 1.5 POC-621 VESA Mounting
- Figure 1.6 POC-621 Series Front Panel
- 1.3.1 Optional Modules
- 1.3.2 Cleaning and Disinfecting the Solution
- 1.4 Operating Principle
- 1.5 Intended User Profile
- 1.6 Front Bezel Button
- 2 System Setup
- 3 Hot Swapping Battery Pack Operation
- 4 Operation and Safety
- A POC-621 Series VESA Mounting
- B Driver Installation
- C PCM-8722 Connector Map
- D PCM-8722 Jumper Settings
- D.1 PCM-8722 Jumper setting
- Table D.1: CN3 ME Manufacturing Mode
- Table D.2: CN5 Clear CMOS
- Table D.3: CN6 (Not Install) Clear ME
- Table D.4: CN8 (Not Install) System Reset
- Table D.5: CN13 LVDS Voltage Setup
- Table D.6: CN40 Power Button (Internal Test Only)
- Table D.7: PCN4 Power Debug (Reserved)
- Table D.8: SW1 Board Setup
- Table D.9: SW1 Pin 4 Speaker Function
- Table D.10: SW2 Panel Resolution/Type Setup
- D.1 PCM-8722 Jumper setting
- E Advanced BIOS Functions
POC-621 Series User Manual 22
2.7 EMC Declaration
Guidance and manufacturer’s declaration – electromagnetic emissions
The model POC-621 SERIES is intended for use in an electromagnetic environment as
specified below. The customer or the user of the POC-621 SERIES should assure that it is
used in such an environment.
Emissions test Compliance
Electromagnetic environment –
guidance
RF emissions
CISPR 11
Group 1
The model POC-621 Series uses
RF energy only for its internal
function. Therefore, its RF emis-
sions are very low and are not
likely to cause any interference in
nearby electronic equipment.
RF emissions
CISPR 11
Class B
The model POC-621 Series is
suitable for use in all establish-
ments, including domestic estab-
lishments and those directly
connected to the public low-volt-
age power supply network that
supplies buildings used for
domestic purposes.
Harmonic emissions
IEC 61000-3-2
Class D
Voltage fluctuations/
flicker emissions
IEC 61000-3-3
Meet the require-
ments
Recommended separation distances between
portable and mobile RF communications equipment and the model POC-621 Series
POC-621 SERIES is intended for use in an electromagnetic environment in which radiated
RF disturbances are controlled. The customer or the user of the model POC -W152C can
help prevent electromagnetic interference by maintaining a minimum distance between
portable and mobile RF communications equipment (transmitters) and the model POC-621
SERIES as recommended below, according to the maximum output power of the commu-
nications equipment.
Rated maximum
output power of
transmitter
W
Separation distance according to frequency of transmitter
m
150 kHz to 80 MHz
d = 1,2
80 MHz to 800 MHz
d = 1,2
800 MHz to 2,5 GHz
d = 2,3
0,01 0,12 0,12 0,23
0,1 0,38 0,38 0,73
1 1,2 1,2 2,3
10 3,8 3,8 7,3
100 12 12 23
P
P
P