Installation Manual

ManualsBrandsCoverking ManualsAutomotiveCoverking Custom Fit Front 50/50 Bucket Seat Cover for Select Honda Pilot Models - Ballistic (Charcoal)

INSTALLATION & CARE

1. If Your Seats Have Removable Headrests - Remove Them

2. Install Seat Back Cover

Depending on your vehicle, you may have to press tab(s) in, poke a paperclip, or press in a slot. This may require two or more people.

Here are some examples:

A. Tab(s) at headrest base

If your headrests have tab(s) at the

baseof the headrest, depress them

and lift the headrest out.

This may be easier with more than

one person.

B. Pin holes on headrest

If your headrests have small holes

instead of visible tabs, insert a

paperclip end into the hole. While

pressing the paperclip in, lift

headrest. This may be easier with

more than one person.

C. Slot and Tab at headrest base

If your headrests have tab(s) and

a slot at the base of the headrest,

depress the tab and press into the

slot at the same time, and lift the

headrest out. This may be easier

with more than one person.

D. Pin hole and tab at

headrest base

If your headrests have tab(s)

and a pin hole at the base of

the headrest, depress the tab

and insert a paperclip end into

the pinhole at the same time,

and lift the headrest out.

Depending on your seat style and vehicle, the installation process will differ. The following information will help you figure out how your specific

covers install.

IMPORTANT: If your seats have integrated airbags, make sure you install the seat back covers in such a way that the airbag flaps are

placed over the airbag location. Covers are labeled with sitckers: “DRIVER” and “PASSENGER”.

CUSTOM SEAT COVER INSTALLATION

BEFORE INSTALLATION:

• Read entire installation instructions before proceeding

• Use caution when reaching under power seats - some seats have sharp mechanisms.

IF YOU DO NOT HAVE ACCESS THROUGH

THE SEAT CUSHIONS:

If you are unable to place your hand through

the middle of the seat cushions and see your

fingers emerge from the other side, your vehicle

may have a flap that is secured by metal rings

or elastic straps. You’ll need to release this flap

to proceed. For more information please vistit

support.coverking.com.

SEAT BACK AND BOTTOM ONE PIECE?

Some vehicle seat designs require the backrest

and seat bottom covers to be joined. After

the covers are slipped over the seat back and

bottom, there is a special accomodation that you

push between the cushions. For more detailed

information please visit install.coverking.com.

TIP 1: It may be easier (necessary on some seats) to fold your

seat forward to pass the flap through.

STEP 2. Pass the bottom flap

through the opening between seat

back and seat bottom, then attach

velcro.

STEP 1. If the seat has an armrest,

place it in the “up” position. If the

cover has a zipper, unzip it. Pull

cover over top of the seat. It may

be helpful to start with the cover

inside-out (as shown).

B. C.

3IS055

Summary of content (2 pages)

PAGE 1
INSTALLATION & CARE CUSTOM SEAT COVER INSTALLATION BEFORE INSTALLATION: • Read entire installation instructions before proceeding • Use caution when reaching under power seats - some seats have sharp mechanisms. 1. If Your Seats Have Removable Headrests - Remove Them Depending on your vehicle, you may have to press tab(s) in, poke a paperclip, or press in a slot. This may require two or more people. Here are some examples: A.
PAGE 2
3. Install Seat Bottom Cover Step 1. Position cover over seat bottom. Pass flap between seat back and seat bottom. (Similar to the seat back cover installation, it may be easier if you fold the seat back forward) Join and tighten the buckles (A,B) under the seat. Step 2. Then attach the side hooks (C,D) to the buckle straps. View from under the seat 4. Install Console Cover (If Applicable) E B Step 1. Slide on console top, then console bottom. Step 2.