HZB-15NB/S
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS…………………………………………………1 PREPARING YOUR ICE MAKER FOR USE IMPORTANT SAFETY TIPS…………………………………………………………………….2-3 GETTING TO KNOW YOUR UNIT……………………………………………………… ……………………………………………………….. ..4 4 OPERATING PROCEDURES & MAINTENANCE …………………………………...4-5 USING YOUR ICE MAKER HOW TO START THE UNIT ………………………………………………………………….5 CLEAN ……………………………………………………………………………………….6 SYSTEM CLEANING/SANITIZING PROCEDURE HOW TO OBTAIN THE ICE-CUBE ICE SCOOP POSITION ………………………………………….
DANGER – Risk Of Fire Or Explosion. Flammable Refrigerant Used. To Be Repaired Only By Trained Service Personnel. Do Not Puncture Refrigerant Tubing. CAUTION – Risk Of Fire Or Explosion. Flammable Refrigerant Used. Consult Repair Manual/Owner’s Guide Before Attempting To Install or Service This Product. All Safety Precautions Must be Followed. CAUTION – Risk Of Fire Or Explosion. Dispose Of Property In Accordance With Federal Or Local Regulations. Flammable Refrigerant Used .
GETTING TO KNOW YOUR UNIT 1、Float switch； 2、Secondary water reservoir: It connects directly with the evaporator； 3、Water reservoir； 4、Maximum water level； 5、Filter； 6、Control Panel： A. Ice-making and cleaning buttons； B. Ring indicator light； C. Water lack indicator light； D.
5. Allow 2 hours for the refrigerant fluid to settle down before plugging your ice maker in. 6. The power plug must be accessible directly. WARNING: Fill it with potable water only. Only use drinking water. DANGER *Improper use of the grounded plug can result in the risk of electrical shock. is damaged, please call our customer service. If the power cord 1. This unit should be properly grounded for your safety.
3. Plug in and the ring indicator will red light on. If you press the "Ice /Clean" button, the machine will start making ice; If long press the "Ice/Clean" button, it will do automatic cleaning. CLEAN For the first time, or the clean procedure has not been running for a long time, it is highly recommended to run this procedure at first. 1. Before the cleaning procedure, please make sure the water drain cap has been inserted into the appliance; otherwise it will not work properly. 2.
Tips: remove the top back cover by pulling up the front transparent cover gently. Change water in the water reservoir every 24 hours to ensure a reasonable hygiene level. If the unit isn’t to be used, drain all water & dry the water reservoir. System Cleaning/Sanitizing Procedure 1.Unplug the nugget ice maker. 2.Take off the bottom drain cap and drain out the water to a sink. See the figure below. 3.
above water solution (and then plug in to turn on the “cleaning function” for about 5 minutes. After that, unplug it again to leave the white vinegar in the unit more than 12hours). 4.Pour the solution into the water reservoir, up to the “MAX” water level. See the figure below. 5. Plug in the Nugget ice maker, press and hold the "Ice/Clean" button for 5 seconds to initiate the cleaning process(15mins). See the figure below. 6.
7. Repeat the step 4 to 6 with fresh water for two more cycles to rinse the inside. 8. Replace the drain cap on the bottom. See the figure below. 9. When completed, fill the unit with fresh water and press the "Ice/Clean" button to start ice making process. See the figure below.
How to obtain the ice-cube 1. Before we start making ice, please make sure the water drain cap has been inserted into the appliance; otherwise it will not work properly. 2. Press “Ice/Clean” button , Ring indicator light flashes white，it begin to work, Press this button again, it will stop making ice. 3. For the first time, or if the appliance has not been used for a long time, it is recommended to clean this appliance before you start to make ice. 4.
TROUBLESHOOTING PROBLEM “Add Water ” indicator turns on “ICE FULL” indicator turns on Ring indicator light flashes red POSSIBLE CAUSE Lack of Water. Stop the ice maker, fill water, and press “Ice/Clean” button again to restart the unit. There is too much ice. Suggest you ice-cube. No ice cube inside. Remove the probable obstacle inside or clean the inside wall of the ice storage Ambient temperature or water temperature in inner tank is too high.
TECHNICAL PARAMETERS & CIRCUIT DIAGRAM TECHNICAL PARAMETERS Model HZB-15NB/S HZB-15NB/S Protection Type Power Ice Making Current Refrigerant I 115V/ 60Hz 115V/6 2.
V1
