CONTENTS IMPORTANT SAFETY............................................................................................................................2 SPECIFICATION...................................................................................................................................................4 DIMENSION/CONNECTION.....................................................................................................................4 RATING......................................................
IMPORTANT SAFETY When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock, and injury to persons or property. Read all instructions before using any appliance. Use this appliance only for its intended purpose as described in this owner’s manual. This ice-maker must be properly installed in accordance with the installation instructions before it is used. This unit must be positioned so that the plug is accessible.
power supply. WARNING: Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance. DANGER – Risk Of Fire or Explosion. Flammable Refrigerant Used. Do Not Use Mechanical Devices To Defrost Ice Maker. Do Not Puncture Refrigerant Tubing. DANGER – Risk Of Fire Or Explosion. Flammable Refrigerant Used. To Be Repaired Only By Trained Service Personnel. Do Not Puncture Refrigerant Tubing. CAUTION – Risk Of Fire Or Explosion. Flammable Refrigerant Used.
SPECIFICATIONS DIMENSIONS/CONNECTIONS 516 [20.3] 47 [1.9] 550 [21.7] 426 [16.8] 53 [2.1] 159 [6.3] 351 [13.8] 820 [32.3] 850 [33.5] 380 [15.0] 824 [32.4] 1) 2) Rating MODEL HBZB-36F POWER SUPPLY VOLTAGE 1Phase, 115V/60Hz CLAIMATE CLASS 10-40℃(50-104℉) ELECTRICAL PROTECTION CLASS I ICE MAKING RATING (Amps) 2.6Amp ICE HARVEST RATING (Amps) 3.0Amp ICE MAKING CAPACITY (KG/24H) REFRIGERANT CHARGE NET WEIGHT(lbs) 36kg/24Hour * R290 2.65Oz / 75g 53.
GENERAL INFORMATION 1) Main Unit Construction ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ 1. Door 2. Ice-making & its water tank assembly: Including ice-making evaporator, water tank, water pump and some detecting parts 3. Handle 4. Ice tank 5. Operation panel 6. Air outlet: Must keep the air circulating smoothly, hot air will blow out when unit running. 7. Water draining port: Normal plugged with the cap. When need to drain the water, unplug the cap. And connect the white drain pipe. 8.
D. E. F. G. H. Water tank. Water supplying pipe. Cover board on the right side of the evaporator. Water level switch installing plate. Water drain pipe of the water tank：when ice-making, this pipe should be clamped in the slot of the water tank wall; And when draining, this pipe should be pulled out. I. Water pump. J. Water level detecting switch. 3) Operation panel A.
OPERATING PROCEDURES & MAINTENANCE UNPACKING YOUR ICE MAKER 1. Remove the exterior and interior packaging. Check if all the accessories, includingthe instruction manual, ice scoop, white water inlet pipe, the water draining pipe, the quick connector (connecting a 1/4-inch connector with a 1/2-inch one), etc., are inside or not. If any parts are missing, please contact our customer service. 2. Remove the tapes for fixing the door and inner cabinet, ice scoop, etc..
6. Release the 2 screws on the handle, fix on the opposite side of the door. Remove the screw on the right fixpiece, fix the left fix piece(from accessory bag) to the door. Left fix piece Change Right fix piece hinge pin Handle Handle Right bottom Hinge Move 7. Remove the right bottom hinge by removing the 3 screws, than fix the 3 screw back without hinge. 8. Remove the hinge pin on the right bottom hinge and reinstall on the left bottom hinge. 9.
INSTALLATION LOCATION REQUIREMENT a) This unit is not for outdoor use. Keep the proper room temperature and inlet water temperature according to above specification table. Otherwise it will affect the ice making performance. b) This unit should not be located near any heat resource. c) The unit should be located on a firm & level foundation at normal counter top height.
ELECTRICAL REQUIREMENT & CONNECTIONS WARNING: THIS UNIT MUST BE EARTHED. Electrical Shock Hazard Plug into a grounding wall outlet. Never remove the ground prong. Use a separate power supply or receptacle. Never use an adapter. Never use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Before you move your ice maker into its final location, it is important to make sure you have the proper electrical connection.
WATER CONNECTION FOR YOUR ICE MAKER Important: Be sure to use the new hose-sets supplied with the appliance to connect to water mains and that old hose-sets should not be reused. 1. Connect the water supplying hose to the unit Step 1: First remove the tape on the water inlet port for water supply (indicated in the following illustration “B”) located at unit back, then use your other hand’s finger to press the out circle.
OPERATING YOUR UNIT Operation Button and Display Area Diagram THE ICE MAKING PROCESS 1. Starting up: Plug in the power plug, and the symbol will flash in the display window. Press the ON/OFF button on the control panel. The machine will start to make ice when the external pipe adds water to reach the standard level on the water tank through the electromagnetic water valve. Thereafter, the symbol will remain bright constantly in display window and symbol will rotate.
panel, the unit shuts down and will be in the standby mode. If you press "ON/OFF" longer than 5 seconds during ice-making process, then the unit enters the deicing process directly. This function can help remove the ice on the ice plate. Press "ON/OFF" to shut down the machine. 6. Timing setting：Setting range：1-24 hours Time shutdown：When the unit is running, it can set up the timing shutdown. Time on：When the unit is in standby mode, you can set the unit with ON-TIMER.
WIRING DIAGRAM Normal Sounds Your new ice maker may make sounds that are not familiar to you. Most of the new sounds are normal. Hard surfaces like the floor, walls and cabinets can make the sounds seem louder than they actually are. The following describes the kinds of sounds that might be strange to you and reasons causing them. You will hear a swooshing sound when the water valve opens to fill the water tank for each cycle.
illustration. 7. Disconnect the water drain pipe to the main drain pipeline or floor drain, and plug on the drain cap again. 8. Drop the door open to allow for circulation and prevent mold and mildew. 9. Leave water supply hose and power cord disconnected until ready to reuse. 10. Dry the interior & wipe the outside of the unit. 11. Put a plastic bag on the unit to resist out dust & dirty.
the ice making system has been cleaned, and the storage bin is empty. 1. Disconnect power to the unit. 2. Open the door and with a clean cloth, wipe down the interior with a sanitizing solution made of 28g of household bleach or chlorine and 7.5L of hot water(95℉ to 115℉) . 3. Rinse thoroughly with clear water. The waste water will be drained out through the drain pipe. 4. Reconnect power to the unit. The ice scoop should be washed regularly. Wash it just like any other food container.
Suggestion: After cleaning the interior parts and install back to their respective position, and make the machine back to work, discard first batch of ice. Ice Making Assembly System Cleaning by Using Nu-Calgon Nickle Safe Ice-machine Cleaner Minerals that are removed from water during the freezing cycle will eventually form a hard scaly deposit in the water system. Cleaning the system regularly helps remove the mineral scale buildup.
The ice machine cleaner contains acids. DO NOT use or mix with any other solvent-based cleaner products. Use rubber gloves to protect hands. Carefully read the material safety instructions on the container of the ice machine cleaner. 8. Then open the water faucet of the main water supply, Let the water flow in the unit. Again press the“TIMER CLEAN”button on control panel for more than 5 seconds, to enter the self-Cleaning program.
NORMAL TROUBLE SHOOTING Problem “ ” indicator is on. The unit start to enter the ice making process, but no water flows in the unit, and the “ ” indicator Possible Cause Solution No water supply Check the main water supply pressure or check whether the water supply hose is blocked ornot, adding the water pressure or cleaning the hose necessary. The floating ball of the water level detecting switch is blocked, can’t be raised up. Clean the water tank and the water level detecting switch.
ERROR INDICATOR a) Ambient temp sensor breakdown-----Display E1 in the digital panel. b) The machine does not make ice or the gas leak-----Display E2 in the digital panel. c) The drain pump dose not work-----Display E in the digital panel(Only for the unit which has drain tank). d) Magnetic control switch cut off----- “Full” light will be on when plugging on or just turning on the unit. And it will delete the breakdown display if this switch is electric shorted.
Thank you for purchasing this product! If you have any questions about the product, such as missing parts, damaged products, product assembling, and operation, please contact us via Amazon Message or customer service number: 213-4467172 or 661-4358826. IMPORTANT Please call our customer service department for any consulting: 213-4467172 661-4358826 (8:30am - 5:30pm P.S.T.) DATED PROOF OF PURCHASE IS REQUIRED FOR WARRANTY SERVICE.
