CT169 8” BENCH GRINDER with 28”x 2” BELT SANDER User Manual
TABLE OF CONTENTS General Safety Instructions for Machines ............................................................... 3 Specific Safety Instructions..................................................................................... 4 CT169 Features ...................................................................................................... 5 Physical Features ................................................................................................... 6 Proper Grounding ..............
GENERAL SAFETY INSTRUCTIONS FOR MACHINES Extreme caution should be used when operating all power tools. Know your power tool, be familiar with its operation, read through the owner’s manual and practice safe usage procedures at all times. ALWAYS read and understand the user manual before operating the machine. CONNECT your machine ONLY to the matched and specific power source. ALWAYS wear safety glasses respirators, hearing protection and safety shoes, when operating your machine.
CT169 - 8” BENCH GRINDER w/BELT SANDER SPECIFIC SAFETY INSTRUCTIONS ALWAYS read and understand the user manual before operating the grinder. MAKE SURE you are wearing safety glasses while operating the grinder or sander. The small particles becoming airborne during operation can seriously damage your eyes. ALWAYS wear a dust mask or a respirator while grinding or sanding. The dust produced during operation can lead to serious respiratory problems if inhaled.
CT169 – BENCH GRINDER w/BELT SANDER FEATURES MODEL CT169 – 8” BENCH GRINDER with BELT SANDER As part of the growing line of Craftex woodworking equipment, we are proud to offer the CT169, an 8” Bench Grinder with Sander. The Craftex name guarantees Craft Excellence. By following the instructions and procedures laid out in this user manual, you will receive years of excellent service and satisfaction.
CT169 - 8” BENCH GRINDER WITH BELT SANDER PHYSICAL FEATURES 6
PROPER GROUNDING Grounding provides a path of least resistance for electric current to reduce the risk of electric shock. Make sure the cord is plugged into a properly installed and grounded power outlet. To prevent electrical hazards, have a qualified electrician ensure that the line is properly wired. Make sure that the appliance is connected to an outlet having the same configuration as the plug. If an adaptor plug is used, it must be attached to the metal screw of the receptacle.
UNPACKING The machine is properly packaged and shipped complete in a carton for safe transportation. When unpacking, carefully inspect the carton to ensure that nothing has been damaged during transit. Open the carton and check that the grinder and the parts are in good condition. Use bolts (not provided) that exceed the thickness of the base plus the thickness of the bench top and secure the machine to the workbench.
Adjust the tool rests 1/8” to 1/16” away from the belt and the wheel and tighten the screws. BELT TRACKING Belt tracking means to adjust the belt so that it rides on, the center of the rollers and does not come in contact with the side covers. Figure-3 Installing the eye safety shield TOOL REST / WORK STOP To check if the sanding belt is riding on the center of the wheels, make sure the switch is in the OFF position and the cord is disconnected from the power source.
DUST PORT CT169 features a 1-1/8” dust port located under the rollers. When connecting to a dust collector, use a proper sized hose and make sure all the connections are tightly sealed. TEST RUN Once you have assembled the machine and verified that grinding wheel is secured and belt is tensioned and tracking properly, it is then time to do a test run and see that the machine powers up and runs properly.
GRINDING WHEEL INSPECTION GRINDING WHEEL REPLACEMENT The CT169 comes with an 8” diameter, A36 grit aluminum oxide grinding wheel. The grinding wheel should be inspected properly before installation. To replace the grinding wheel: Clean the dust and/or dirt from the surface of the wheel and inspect it for any cracks, dents, chips, or any kind of external damage. To inspect the wheel for any internal damages: Make sure the switch is in the OFF position and the cord is disconnected from the power source.
SANDING BELT REPLACEMENT To remove and replace the sanding belt: Take the belt off the rollers and replace with a new one. Make sure the switch is in the OFF position and the cord is disconnected from the power source. Move the belt tension lever down to tension the belt and reinstall the belt cover. Remove the belt guard by removing the knob securing the belt cover. See figure-10. Make sure to perform belt tracking adjustment on the when the new belt is installed.
WARRANTY CRAFTEX 2 YEARS LIMITED WARRANTY Craftex warrants every product to be free from defects in materials and agrees to correct such defects where applicable. This warranty covers two years for parts and 90 days for labor (unless specified otherwise), to the original purchaser from the date of purchase but does not apply to malfunctions arising directly or indirectly from misuse, abuse, improper installation or assembly, negligence, accidents, repairs or alterations or lack of maintenance.
