CT170 1”x30” BELT & 5” DISC SANDER User Manual
TABLE OF CONTENTS General Safety Instructions for Machines ............................................................... 3 Specific Safety Instructions..................................................................................... 4 CT170 Features ...................................................................................................... 5 Physical Features ................................................................................................... 6 Proper Grounding ..............
GENERAL SAFETY INSTRUCTIONS FOR MACHINES Extreme caution should be used when operating all power tools. Know your power tool, be familiar with its operation, read through the owner’s manual and practice safe usage procedures at all times. ALWAYS read and understand the user manual before operating the machine. CONNECT your machine ONLY to the matched and specific power source. ALWAYS wear safety glasses respirators, hearing protection and safety shoes, when operating your machine.
CT170 – 1”x30” BELT & 5” DISC SANDER SPECIFIC SAFETY INSTRUCTIONS MAKE SURE the sander is connected to the matched and specific power source instructed in the manual. ALL THE GUARDS must be in place while operating the sander to ensure safety. MAKE SURE before making any adjustments, the switch is in the “OFF” position and the cord is un-plugged from the power source. NEVER sand more than one work piece at a time. ALWAYS wear a dust mask and safety glasses while operating the sander.
CT170 – BELT & DISC SANDER FEATURES MODEL CT170 – 1”x30” BELT & 5” DISC SANDER As part of the growing line of Craftex woodworking equipment, we are proud to offer the CT170, a 1”x30” Belt and 5” Disc Sander. The Craftex name guarantees Craft Excellence. By following the instructions and procedures laid out in this user manual, you will receive years of excellent service and satisfaction. The C170 is a professional tool and like all power tools, proper care and safety procedures should be adhered to.
CT170 – 1”x30” BELT & 5” DISC SANDER PHYSICAL FEATURES 6
PROPER GROUNDING Grounding provides a path of least resistance for electric current to reduce the risk of electric shock. Make sure the cord is plugged into a properly installed and grounded power outlet. To prevent electrical hazards, have a qualified electrician ensure that the line is properly wired. Make sure that the appliance is connected to an outlet having the same configuration as the plug. If an adaptor plug is used, it must be attached to the metal screw of the receptacle.
UNPACKING DUST CHUTE The machine is properly packaged and shipped completely in carton for safe transportation. When unpacking, carefully inspect the carton and ensure that nothing has been damaged and check that the sander and the parts are in good condition. For optimum dust removal the sander is equipped with two dust chutes featuring 13/4” opening. The sanding belt dust chute with the side guard is mounted to the machine using a lock knob and two screws. See figure-3.
BELT TRACKING Belt tracking means to adjust the belt in the center of the rollers so that it runs true and does not wander left or right off the rollers. The belt tracking on CT170 is very simple and easy. The sander is provided with a belt tracking adjustment knob as shown in figure-6. Figure-4 Installing sanding disc dust chute SANDING DISC TABLE CT170 is provided with a work table for disc sanding operation.
MOUNTING The CT170 is provided with 4 pre-drilled holes on its base to allow mounting on a workbench. To mount the sander on a workbench: Figure-7 Adjusting the belt tracking Once the belt is in the center of the rollers, stop turning the adjustment knob and the disc. Reinstall the side cover and connect the cord to the power source. Turn the sander ON and then quickly OFF and watch if the belt is riding true in the center of the rollers.
TEST RUN Once you have assembled the machine it is then time to do a test run and see that the machine powers up and runs properly. Loosen the two hex screws located under the table, securing the platen to the sander frame. All the tools and objects used for assembling the machine should be removed and cleared away during test run. Adjust the platen so that it is almost touching the back of the belt and re-tighten the screws. See figure-10.
Remove the upper guard and the side cover by removing the lock knob and loosening the two screws securing the upper guard and the side cover. See figure13. Figure-11 Squaring table to the belt Figure-13 Removing the side cover The middle roller features spring at the back and can be pushed towards the table. To remove the belt, hold the adjusting shaft guard and apply moderate pressure just to loosen the belt tension and push it towards the table. See figure-14.
Take the belt off the rollers with another hand and replace it with a new one. Once the belt is position on the wheels, remove your hand and the let the adjusting shaft guard to come in its normal position and tension the belt. Perform the belt tracking adjustment and re-install the cover and the table. MITER GAUGE CT170 is provided with a miter gauge and can be used on the disc table.
WARRANTY CRAFTEX 2 YEARS LIMITED WARRANTY Craftex warrants every product to be free from defects in materials and agrees to correct such defects where applicable. This warranty covers two years for parts and 90 days for labor (unless specified otherwise), to the original purchaser from the date of purchase but does not apply to malfunctions arising directly or indirectly from misuse, abuse, improper installation or assembly, negligence, accidents, repairs or alterations or lack of maintenance.
