CX207 1-1/2 HP TABLE SAW User Manual
TABLE OF CONTENTS General Safety Instructions..................................................................................... 3 Specific Safety Instructions..................................................................................... 4 Features.................................................................................................................. 5 Physical Features ...................................................................................................
GENERAL SAFETY INSTRUCTIONS FOR MACHINES Extreme caution should be used when operating all power tools. Know your power tool, be familiar with its operation, read through the owner’s manual and practice safe usage procedures at all times. ALWAYS read and understand the user manual before operating the machine. CONNECT your machine ONLY to the matched and specific power source. ALWAYS wear safety glasses respirators, hearing protection and safety shoes, when operating your machine.
CX207 1-1/2-HP TABLE SAW SPECIFIC SAFETY INSTRUCTIONS NEVER use a saw blade that has missing carbide teeth, loose teeth, or chipped or broken teeth. NEVER stand directly in line with the saw blade when feeding stock into the saw. NEVER place your fingers or hands in the line of cut. If you slip, your hands or fingers may come into contact with the blade. Always use a push stick when ripping narrow pieces. NEVER allow visitors or helpers to stand in line with the saw blade.
CX207 TABLE SAW FEATURES MODEL CX207 1-1/2HP TABLE SAW As part of the growing line of Craftex woodworking equipment, we are proud to offer the CX207 Table Saw. By following the instructions and procedures laid out in this user manual, you will receive years of excellent service and satisfaction. The CX207 is a professional tool and like all power tools, proper care and safety procedures should be adhered to. Motor ..............................................
CX207 1-1/2-HP TABLE SAW PHYSICAL FEATURES Fence Miter Gauge Extension Wing Table Blade Guard & Spreader Rear Fence Rail Fence Scale Indicator Left Front Rail Tube Right Front Rail Tube Rail Support Blade Tilt Hand Wheel ON / OFF Switch Blade Height Hand Wheel & Lock Knob Fence Lock Handle Blade Tilt Scale Stand Rubber Feet Blade Tilt Lock 6
UNPACKING The machine is properly packaged and shipped completely in crates for safe transportation. When unpacking, carefully inspect the crates and ensure that nothing has been damaged during transit. Open the crates and check that the machine and the parts are in good condition. NOTICE! While doing inventory, if you can not find any part, check if the part has already been installed on the machine. Some parts come pre-assembled for shipping purposes.
SETUP Before setting up your machine you should read and understand the instructions given in this manual. The unpainted surfaces of this table saw are coated with a rust preventive waxy oil and you will want to remove this before you begin assembly. Use a solvent cleaner that will not damage painted surfaces. WARNING! CX207 is a very heavy machine, do not over-exert yourself. For safe moving method use fork truck or get the help of an assistant or friend.
ASSEMBLY To assemble your CX207, follow the instructions given below: Assemble the other two legs with the short braces in the same manner. Attach the upper short brace to two stand legs and secure it using carriage bolts, washers and nuts provided. See figure-4. Attach the leg assemblies with the two lower and two upper braces using carriage bolts, washers and nuts provided. See figure-6. Hand tighten the nuts for now.
Insert the bushing onto the front hand wheel shaft and slide the hand wheel onto the shaft with it is flat side aligned with the flat side of the shaft. Thread the lock knob onto the shaft as shown in figure-8. WARNING! CX207 is a very heavy machine, do not over-exert yourself. For safe moving method use fork truck or get the help of an assistant. Now, get the help of an assistant and turn the saw upright with the stand and place a level on the table.
Inspect the mating surfaces of the extension table and main table for any foreign material that can cause misalignment when assembled. Make sure the mating surfaces of the main table and the extension wings are clean and attach the extension wings to the table with the help of an assistant holding the table. Secure it using hex bolts and washers provided. See figure 12.
and the top part of the rails are flush with each other and parallel to the table and extension wings. Now, tighten all the fasters properly. Connect the left and right fence rails to each other by sliding the two pins located on the end of the right rail into the holes on the left rail and tighten all the fasteners. Insert four bolts into the four larger holes on the main table and extension wings. Place a lock washer and a nut onto each bolt from the inner side of the table.
Insert the nuts into the rear slot on the front left rail and align the nuts with the mounting holes on the switch bracket. Use screws and washer and secure the switch bracket to the rail. See figure-20. Figure-22 Installing table insert Figure-20 Installing the switch on the rail CONNECTING TO A DUST COLLECTOR The CX207 features a 2.5” diameter dust port to connect to a dust collector. Attach the push stick holder to the band saw and secure it using a bolt and washer. See figure-21.
TEST RUN Once you have assembled your machine completely, it is then time for a test run to make sure that the machine works properly and is ready for operation. During the test run you should make sure that the machine operates properly when turned ON. Check all the safety features on the machine and make sure all the safety features work properly. 5. Turn OFF the machine. 6. Remove the safety key on the switch to disable the ON button.
SPREADER At the back side of the blade there is a metal plate mounted to the trunnion, called spreader. The spreader prevents the kerf of the work-piece from pinching the blade and causing kick back. BLADE GUARD The clear polycarbonate guard allows the operator to see the blade cutting the workpiece during cutting operation. The guard covers the blade on both sides and lifts up as the work-piece is fed into the blade and returns to the table surface when the workpiece has passed through the blade.
piece carefully before cutting and wear eye protection. Some woods with excessive twisting or wrapping are un-stable while cutting. This situation can be dangerous, because during operation the work-piece can move unexpectedly which can either damage the blade or hurt the operator. WARNING! If the wood is slightly cupped, make sure the cupped face of the wood is held against the table or the fence.
OPERATIONS Before doing the operation, make sure all the parts of the machine are assembled properly and you have done the test run. Make sure you have read the manual and you are familiar using the table saw, knowing all the safety features on this machine. Since the blade guard can not be used when doing non-through cuts, there is great possibility of kickback. Make sure to have the riving knife installed, when using standard saw blade to perform non-through cuts.
Connect the cord to the power source and turn the table saw “ON”. Let the blade to reach the full speed and feed the workpiece through the blade using a push stick, until the work-piece completely passes the saw blade. See figure-30. with the blade and the blade is cutting the waste side of the line. Connect the cord to the power source and turn the table saw “ON”. Let the blade to reach its full speed and hold the work-piece against the face of the miter gauge.
ADJUSTMENTS MAIN TABLE TO BLADE PARALLELISM Your CX207 will give a better result if the main table is parallel to the blade. If it is not parallel, the result you will get will be poor and low quality. Figure-32 Marking the angle of cut To check if the table is parallel to the blade, use an adjustable square and measure the distance between the miter slot on the table and the edge of the blade (front or back) as shown in figure-33.
TO ADJUST THE TABLE: Make sure the switch is in the “OFF” position and the cord is unplugged from the power source. Loosen the four mounting bolts in the trunnion mounting locations and slightly tap the trunnions as needed. When the table is parallel to the blade, re-tighten the mounting bolts. BLADE GUARD SPREADER & RIVING KNIFE ALIGNMENT The blade guard spreader and riving knife must be aligned with the blade for safe and accurate cutting operation.
Turn the table saw “OFF” and remove the cord from the power source. MAINTENANCE Loosen the lock nut and the hex bolt shown in figure-35. During the life of your machine, you will need to practice some regular maintenance to keep your table saw in peak performance condition. WARNING! Make sure the machine’s power switch is OFF and the cord is disconnected from the power source when installing / removing any part or servicing the sander.
The following components on the CX207 needs to be lubricated. Use grease to lubricate the components and rotate the hand wheel to spread the grease.
WARRANTY CRAFTEX 3 YEARS LIMITED WARRANTY Craftex warrants every product to be free from defects in materials and agrees to correct such defects where applicable. This warranty covers three years for parts and 90 days for labour (unless specified otherwise), to the original purchaser from the date of purchase but does not apply to malfunctions arising directly or indirectly from misuse, abuse, improper installation or assembly, negligence, accidents, repairs or alterations or lack of maintenance.
