CX404 1-HP DUST COLLECTOR User Manual
TABLE OF CONTENTS General Safety Instructions.............................................................3 CX404 Specific Safety Instructions .................................................4 Features..........................................................................................5 Physical Features ...........................................................................6 Unpacking.......................................................................................7 Setup ...................
GENERAL SAFETY INSTRUCTIONS Extreme caution should be used when operating all power tools. Know your power tool, be familiar with its operation, read through the owner’s manual and practice safe usage procedures at all times. CONNECT your machine only to the matched and specific power source. ALWAYS wear safety glasses respirators, hearing protection and safety shoes, when operating your machine. DO NOT wear loose clothing or jewelry when operating your machine.
CX404 – 1 HP DUST COLLECTOR SPECIFIC SAFETY INSTRUCTIONS Read and understand the instruction manual before operating the dust collector. Basic precautions listed below should always be followed when using your dust collector to reduce the risk of injury, electrical shock or fire. The CX404 is designed to collect NEVER operate the dust collector with sawdust only. all blast gates closed.
CX404 FEATURES MODEL CX404 – 1 HP DUST COLLECTOR As part of the growing line of Craftex CX-Series woodworking equipment, we are proud to offer the CX404 a 1-HP Dust Collector. By following the instructions and procedures laid out in this owner’s manual, you will receive years of excellent service and satisfaction. The CX404 is a professional tool and like all power tools, proper care and safety procedures should be adhered to. Motor ...................................... 1 HP, 110 Volt, 7 Amps Safety .....
CX404 - 1 HP DUST COLLECTOR PHYSICAL FEATURES 1 Micron Filtration Bag Collector Body Outlet Connector Collector Ring Support Rod Impeller Assembly Support Casters Easy-On Collection Bag Base
UNPACKING The machine is properly packaged in a carton for safe transportation. When unpacking, carefully inspect the carton and ensure that nothing has been damaged during transit. While doing the inventory if you can not find any part, check if the part is already installed on the machine. CONTENTS QTY A. Motor & Impeller Assembly ............... 1 B. Collector Ring.................................... 1 C. Base .................................................. 1 D. Impeller Support.............
PROPER GROUNDING Grounding provides a path of least resistance for electric current to reduce the risk of electric shock. CX404 is for use on a normal 110 volt circuit. Make sure that the machine is connected to an outlet having the same configuration as the plug. If an adaptor plug is used, it must be attached to the metal screw of the receptacle. To prevent electrical hazards, have a qualified electrician ensure that the line is properly wired.
ASSEMBLY Follow the instructions below to assemble your CX404. Place the base unit upside down and install the swivel casters to the base unit using screws and washers provided. See figure-3. Figure-3 Installing the casters Place the base unit upright and attach the impeller support to the base by aligning the four holes on the impeller support with the four holes on the base unit. Secure it using screws and washers provided as shown in figure-4.
Figure-9 Installing the upper bag Figure-7 Installing the collector ring Install the collector ring support rod with one end collector ring and the other end to the base unit using screws provided. See figure-8. Figure-8 Installing the collector ring support rod Your dust collector should come with a regular bottom bag as well as a set of EasyOn bags. Insert the belt clamp through the easy-on bottom bag and attach the bottom bag to the dust collector as shown in figure-10.
TEST RUN Once you have assembled your dust collector, it is then time for a test run to make sure that the machine works properly and is ready to use. Remove all the tools used for assembling the machine components. Walk around the machine, ensure all nuts, bolts, and screws are tightened and the machine is properly assembled. Connect the cord to the power source and turn the machine ON.
MAINTENANCE Maintenance on this machine is fairly simple. Each time you use your dust collector, make sure to properly clean the bags and take a quick inventory of your machines performance. Check the dust collector regularly for loose bolts, screws, ensure the dust collection bag has no tears, and ensure all wires are in good condition. BAG CLEANING Empty the collection bag on a regular basis. The machine will run more efficiently if the collecting bag is emptied regularly.
CX404 DUST COLLECTOR PARTS BREAKDOWN 13
CX404 DUST COLLECTOR PARTS LIST REF# 1 2 4 5 6 7 8 9 10 11 12 12-1 13 14 14-1 15 16 17 18 19 20 20-1 21 22 23 24 25 26 27 28 DESCRIPTION Caster Pan Head Screw Base Plate Pan Head Screw Inlet Cover Hex Screw Set Screw Washer Turbo Fan Collector Body Washer Nut Hex Screw Hex Screw Hex Screw Hex Screw Switch Switch Key Motor Gasket Column Column Flange Key Packing Collector Ring Easy-On Collection Bag Filter Bag Power Cord Open End Wrench Hex Wrench SIZE QTY 4 3/16” x 5/16” 16 1 3/16” x 3/8” 12 1 M6 x 20 1
WARRANTY CRAFTEX 3 YEAR LIMITED WARRANTY Craftex warrants every product to be free from defects in materials and agrees to correct such defects where applicable. This warranty covers three years for parts and 90 days for labour (unless specified otherwise), to the original purchaser from the date of purchase but does not apply to malfunctions arising directly or indirectly from misuse, abuse, improper installation or assembly, negligence, accidents, repairs or alterations or lack of maintenance.