CX405 2-HP DUST COLLECTOR User Manual
TABLE OF CONTENTS General Safety Instructions.............................................................3 CX405 Specific Safety Instructions .................................................4 Features..........................................................................................5 Physical Features ...........................................................................6 Unpacking.......................................................................................7 Setup ...................
GENERAL SAFETY INSTRUCTIONS Extreme caution should be used when operating all power tools. Know your power tool, be familiar with its operation, read through the owner’s manual and practice safe usage procedures at all times. CONNECT your machine only to the matched and specific power source. ALWAYS wear safety glasses respirators, hearing protection and safety shoes, when operating your machine. DO NOT wear loose clothing or jewelry when operating your machine.
CX405 – 2 HP DUST COLLECTOR SPECIFIC SAFETY INSTRUCTIONS Read and understand the instruction manual before operating the dust collector. Basic precautions listed below should always be followed when using your dust collector to reduce the risk of injury, electrical shock or fire. The CX405 is designed to collect NEVER operate the dust collector with sawdust only. all blast gates closed.
CX405 FEATURES MODEL CX405 – 2 HP DUST COLLECTOR As part of the growing line of Craftex CX-Series woodworking equipment, we are proud to offer the CX405 a 2-HP Dust Collector. By following the instructions and procedures laid out in this owner’s manual, you will receive years of excellent service and satisfaction. The CX405 is a professional tool and like all power tools, proper care and safety procedures should be adhered to. Motor ......................................
CX405 - 2-HP DUST COLLECTOR PHYSICAL FEATURES Top Bag Support 1 Micron Filtration Bag 2-HP 220-V Motor Collector Ring Collector Hose Collector Ring Support Dual Intake 4” Each Easy-On Collection Bag Casters Base
UNPACKING The dust collector is properly packaged in a carton for safe transportation. When unpacking, carefully inspect the carton and ensure that nothing has been damaged during transit. While doing the inventory if you can not find any part, check if the part is already installed on the machine. CONTENTS QTY A. Collector Ring.................................... 1 B. Motor / Impeller Unit .......................... 1 C. Top Bag............................................. 1 D. Bottom Bag .......
PROPER GROUNDING Grounding provides a path of least resistance for electric current to reduce the risk of electric shock. CX405 is for use on a normal 220 volt circuit. Make sure that the machine is connected to an outlet having the same configuration as the plug. If an adaptor plug is used, it must be attached to the metal screw of the receptacle. To prevent electrical hazards, have a qualified electrician ensure that the line is properly wired.
ASSEMBLY Follow the instructions below to assemble your CX405. Place the gasket on the motor / impeller opening as shown in figure-5. Gasket Place the base unit upside down and install the swivel casters to the base unit using screws, nuts and washers provided. See figure-3. Figure-5 Positioning the gasket Figure-3 Installing the casters Position the outlet connector onto the gasket and the motor / impeller opening securing it using screws and washers provided. See figure-6.
Use the hose clamps provided to secure the hose on both ends. Figure-7 Installing the collector ring support Attach the collector ring to the collector ring supports and the upper bag support to the collector ring as shown in figure-8. Make sure that the hose opening of the collector ring is facing the motor / impeller. Secure the collector ring from both sides using screws, nuts, and washers provided.
Your dust collector should come with a regular bottom bag as well as a set of EasyOn bags. Insert the belt clamp through the Easy-On bottom bag and attach the bottom bag to the dust collector as shown in figure-11. TEST RUN Once you have assembled your dust collector, it is then time for a test run to make sure that the machine works properly and is ready to use. Remove all the tools used for assembling the machine components.
OPERATION Operating the CX405 dust collector is very simple and straightforward. Make sure the dust collector is properly assembled and worked during the test run. Move the CX405 close to the machine and use a proper sized hose connecting the hose with its one end to the machine and the other end to the dust collector. Make sure the connections are secured using hose clamps and connect the ducting ground and the dust collector is ready for operation.
CX405 DUST COLLECTOR PARTS BREAKDOWN 13
CX405 DUST COLLECTOR PARTS LIST PART# 1 2 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 DESCRIPTION Caster Hex Head Screw Base Plate Pan Head Screw Intake Cover Socket Head Hex Screw Hex Head Screw Washer 12” Impeller Fan Impeller Body Washer Pan Head Screw Hex Head Screw Hex Head Screw Motor Switch Motor Nut Collector Outlet Adapter Hose Clamp Hose Collector Bag Collector Support Posts Collector Gasket Filter Bag Support Cloth Filter Bag Gasket Dual 4” Intake Key Powe
WARRANTY CRAFTEX 3 YEAR LIMITED WARRANTY Craftex warrants every product to be free from defects in materials and agrees to correct such defects where applicable. This warranty covers three years for parts and 90 days for labour (unless specified otherwise), to the original purchaser from the date of purchase but does not apply to malfunctions arising directly or indirectly from misuse, abuse, improper installation or assembly, negligence, accidents, repairs or alterations or lack of maintenance.
