Installation Guide

ManualsBrandsCraftmade ManualsFlush Mount LightingBarrett Place 15-in Mocha Bronze Traditional incandescent Semi-Flush Mount Light

ASSEMBLY & INSTALLATION

IN STRUCTION FOR #24263

Please read carefully and save these instructions, as you may need them at a later date.

GENERAL

All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If

you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician.

Remove the fixture and the mounting package from the box and make sure that no parts are missing by

referencing the illustrations on the installation instructions.

CAUTION

Turn off the main power at the circuit breaker before installing the fixture, in order to prevent possible shock.

17. ARM

18. CLUSTER ASSEMBLY

19. NIPPLE

20. GLASS SHADE

21. PLATE

22. RUBBER WASHER

23. GASKET

24. NIPPLE

25. BOTTOM FONT

26. FINIAL

FIG

ASSEMBLY AND INSTALLATION

1. At the center of the BACK PLATE(2) there are eight perforated slots. Knock out the set matches your

OUTLET BOX (1).

2. Screw the FIXTURE MOUNTING SCREWS (13) into the BACK PLATE (2) and thread the HEX

NUTS (14) onto the FIXTURE MOUNTING SCREWS (13), as shown. Secure the position of the

FIXTURE MOUNTING SCREWS (13) by tightening the HEX NUTS (14) against the BACK PLATE

(2).

3. Carefully pass the power supply (6&8) wires and the SUPPLY GROUND WIRE (5) through the center

hole of the BACK PLATE (2). Secure the BACK PLATE (2) to the OUTLET BOX (1) with

MOUNTING SCREWS (3).

4. Attach the BLACK SUPPLY WIRE (8) to the SMOOTH (or BLACK) FIXTURE LEAD WIRE (9) by

using the WIRE CONNECTOR (10). At the same manner, attach the WHITE SUPPLY WIRE (6) to

the RIBBED (or WHITE) FIXTURE LEAD WIRE (7). Loop the FIXTURE GROUND WIRE (4)

around the GROUND SCREW (11) of the BACK PLATE (2). (Note: Be sure to provide an extra 3”

length of the FIXTURE GROUND WIRE (4) for connection to the SUPPLY GROUND WIRE (5).)

Tighten the GROUND SCREW (11). Connect the remaining FIXTURE GROUND WIRE (4) to the

SUPPLY GROUND WIRE (5) using a WIRE CONNECTOR (10). Place wiring and connections

inside the OUTLET BOX (1).

5. Place the COVER PLATE (12) onto the FIXTURE MOUNTING SCREWS (13), and secure it into

place using the DECORATIVE NUTS(15) provided. Attach the ARM(17) onto the canopy and cluster

assembly, fix with the NUT SCREW(16) and BALL NUT(15).

6. Screw light bulbs into the sockets and make sure they do not exceed the maximum wattage

specified on the fixture’s wattage rating label,

MAXIMUM 60W.

7. Thread the NIPPLE(19) onto the cluster assembly, secure with the hex nut. Slide the PLATE(21),

GLASS SHADE(20), RUBBER WASHER(22) and GASKET(23) over the NIPPLE(19), secure with

the HEX NUT(24). Slide the BOTTOM FONT(25) over the NIPPLE(19), fix with the FINIAL(26).

1. OUTLET BOX

2. BACK PLATE

3. MOUNTING SCREW

4. FIXTURE GROUND WIRE

5. SUPPLY GROUND WIRE

6. WHITE SUPPLY WIRE

7. RIBBED (OR WHITE) FIXTURE

LEAD WIRE

8. BLACK SUPPLY WIRE

9. SMOOTH (OR BLACK)

FIXTURE LEAD WIRE

10. WIRE CONNECTOR

11. GROUND SCREW

12. COVER PLATE

13. FIXTURE MOUNTING

SCREW

14. HEX NUT

15. DECORATIVE NUT

16. NUT SCREW