Installation Guide
ASSEMBLY AND INSTALLATION
1. Take the parts out of the mounting package . Screw the end of the NIPPLE (4) into the center hole of the
MOUNTING BRACKET (2) and thread both 1/8” IPS HEX NUT(5) several turns onto each end of the
NIPPLE(4) but do not tighten the 1/8” IPS HEX NUTS (5). Pull the SUPPLY WIRES (9 & 11) and the
SUPPLY GROUND WIRE (8) out from the OUTLET BOX (1) and attach the MOUNTING BRACKET (2)
assembly to the OUTLET BOX (1) using the slotted holes of the MOUNTING BRACKET (2) and the
MOUNTING SCREWS (3) provided. (See Fig. 1)
2. Thread the SCREW COLLAR LOOP (6) onto the bottom end of the NIPPLE (4). Place the CANOPY (15)
over the OUTLET BOX (1) and adjust the SCREW COLLAR LOOP (6) and NIPPLE (4) until the midpoint of
the outside threads on the SCREW COLLAR LOOP (6) is centered (aligned) with the surface of the CANOPY
(15). Remove the CANOPY (15) and tighten both 1/8” IPS HEX NUTS (5) down on the MOUNTING
BRACKET (2) and the SCREW COLLAR LOOP (6). (See Fig. 1)
3. Thread the CENTER TUBE(22) onto the NIPPLE(27) till tight. Thread the NIPPLE(20) into the CENTER
TUBE(22) till tight. Thread the FIXTURE LOOP(18) onto the NIPPLE(19) till tight. Pull the arms so they are
evenly spaced. Loop the CHAIN(23) onto the HOOK(21). (See Fig. 2)
4. Open up the end links of the CHAIN (17) and attach one end of the CHAIN (17) onto the FIXTURE LOOP.
Slide the THREADED RING (16) and the CANOPY (15) onto the CHAIN (17) (in that order) and attach the
other end of the CHAIN (17) to the SCREW COLLAR LOOP (6). Close the ends of the chain links. (See Fig.
1 and 2)
5. Unravel the fixture lead wires(10 and 12) and FIXTURE GROUND WIRE (7) and thread them through every
other link of the CHAIN (17) starting with the chain link attached to the FIXTURE LOOP. Feed the fixture
lead wires(10 and 12) and FIXTURE GROUND WIRE (7) through the SCREW COLLAR LOOP (6) and
NIPPLE (4) assembly. Pull the fixture lead wire(10 and 12) and the FIXTURE GROUND WIRE (7) upward
to remove any excess slack. (See Fig. 1)
6. Attach the power supply wires to the fixture lead wires by connecting the BLACK SUPPLY WIRE (9) to the
SMOOTH FIXTURE LEAD WIRE (10) and the WHITE SUPPLY WIRE (11) to the RIBBED FIXTURE
LEAD WIRE (12). Loop the FIXTURE GROUND WIRE (7) around the GROUND SCREW (14) of the
MOUNTING BRACKET (2). (Note: Be sure to provide an extra 3” length of the GROUND WIRE(7).)
Connect the remaining FIXTURE GROUND WIRE (7) to the SUPPLY GROUND WIRE (8) using a WIRE
CONNECTOR (13). Place wiring and connections inside the OUTLET BOX (1). (See Fig. 1)
ASSEMBLY AND INSTALLATION (Continued)
7. Slide the CANOPY (15) and the THREADED RING(16) up the CHAIN(17). Place the CANOPY (15) over
the OUTLET BOX (1) and secure it in place by screwing the THREADED RING (16) onto the SCREW
COLLAR LOOP (6).(See Fig.1)
8. Thread the NIPPLE(34) into the COUPLING(33), secure with the hex nut. Slide the POLY COVER(35)
over the NIPPLE(34), secure with the FINIAL(36). Pull the ARMS(31) so they are evenly spaced, attach
the ARMS(31) against the RIM(29) inside, secure it by tightening the BALL NUTS(30) into the RIM(29)
through the holes of the ARMS(31), make sure TUBE(32) slide into the CIRCLE(28). (See Fig. 2)
9. Slide the GLASS SHADE(25) over the SOCKET(26), secure with the SOCKET RING(24). (See Fig. 2)
10. Screw light bulbs into the sockets and make sure they do not exceed the maximum wattage
specified on the fixture’s wattage rating label, MAXIMUM 60W.
INSTALLATION IS NOW COMPLETED
ASSEMBLY & INSTALLATION
INSTRUCTIONS FOR #25229
Please read carefully and save these instructions, as you may need them at a later date.
GENERAL
All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If
you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician.
Remove the fixture and the mounting package from the box and make sure that no parts are missing by
referencing the illustrations on the installation instructions.
CAUTION
Turn off the main power at the circuit breaker before installing the fixture, in order to prevent possible shock.
1. OUTLET BOX
2. MOUNTING BRACKET
3. MOUNTING SCREW
4. NIPPLE
5. 1/8” IPS HEX NUT
6. SCREW COLLAR LOOP
7. FIXTURE GROUND WIRE
8. SUPPLY GROUND WIRE
9. BLACK SUPPLY WIRE
FIG. 1
FIG. 2
10. SMOOTH FIXTURE LEAD
WIRE
11. WHITE SUPPLY WIRE
12. RIBBED FIXTURE LEAD
WIRE
13. WIRE CONNECTOR
14. GROUND SCREW
15. CANOPY
16. THREADED RING
17. CHAIN
18. FIXTURE LOOP
19. NIPPLE
20. NIPPLE
21. HOOK
22. CENTER TUBE
23. CHAIN
24. SOCKET RING
25. GLASS SHADE
26. SOCKET
27. NIPPLE
28. CIRCLET
29. RIM
30. BALL NUT
31. ARMS
32. TUBE
33. COUPLING
34. NIPPLE
35. POLY COVER
36. FINIAL