Installation Guide

Please read carefully and save these instructions, as you may need them at a later date. Turn off the main power at the circuit breaker before installing the fixture in order to prevent possible shock. All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections, obtain the services of a qualified electrician. Remove all parts and hardware from the box and the mounting package and make sure that none are missing by referencing the illustrations provided. 1. Pull the SUPPLY WIRES (4 & 6) and the SUPPLY GROUND WIRE (8) out from the OUTLET BOX (1) (not included) and attach the MOUNTING STRAP (2) assembly to the OUTLET BOX (1) using the slotted holes of the MOUNTING STRAP (2) and the OUTLET BOX SCREWS and WASHERS (3). [See Fig. 1] 2. Remove the THREADED RING (15) from the SCREW COLLAR LOOP (13) and set aside. Place the CANOPY (11) over the OUTLET BOX (1) and adjust the SCREW COLLAR LOOP (13) and THREADED ROD (12) until the midpoint of the outside threads on the SCREW COLLAR LOOP (13) is centered (aligned) with the surface of the CANOPY (11). Remove the CANOPY (11) and tighten both HEX NUTS (21) down on the MOUNTING STRAP (2) and the SCREW COLLAR LOOP (13). [See Fig. 1] 3. Thread the FIXTURE LOOP (17) onto the threaded rod at the top of the FIXTURE (16) until tight. Secure the
FIXTURE (16) to the SHADE (22) with the DECORATIVE NUTS (18) provided.
[See Fig. 2]
4. Open CONNECTING CHAIN LINK (19) on one end of the CHAIN (14) to attach the CHAIN (14) to the FIXTURE LOOP (17). Close CONNECTING CHAIN LINK (19). Slide the THREADED RING (15) and the CANOPY (11) onto the CHAIN (14) (in that order). Open CONNECTING CHAIN LINK (19) on the other end of the CHAIN (14) to attach the other end of the CHAIN (14) to the SCREW COLLAR LOOP (13). Close the CONNECTING CHAIN LINK (19). [See Fig. 1 & 2] 5. Unravel the FIXTURE LEAD WIRES (5 & 7) and FIXTURE GROUND WIRE (9) and thread them through every other link of the CHAIN (14) starting with the chain link attached to the FIXTURE LOOP (17). Feed the FIXTURE LEAD WIRES (5 & 7) and FIXTURE GROUND WIRE (9) through the SCREW COLLAR LOOP (13) and THREADED ROD (12). Pull the FIXTURE LEAD WIRES (5 & 7) and the FIXTURE GROUND WIRE (9) upward to remove any excess slack. [See Fig. 1] 6. Attach the power supply wires to the fixture lead wires by connecting the BLACK SUPPLY WIRE (4) to the SMOOTH FIXTURE LEAD WIRE (5) and the WHITE SUPPLY WIRE (6) to the RIBBED FIXTURE LEAD WIRE (7). Loop the SUPPLY GROUND WIRE (8) around the GROUND SCREW (20) on the MOUNTING STRAP (2). [Note: Be sure to provide an extra 3in. length of the SUPPLY GROUND WIRE (8) for connection to the FIXTURE GROUND WIRE (9).] Tighten the GROUND SCREW (20). Connect the remaining SUPPLY GROUND WIRE (8) to the FIXTURE GROUND WIRE (9). Use a WIRE CONNECTOR (10) for all wire connections. Push wiring and connections inside the OUTLET BOX (1). [See Fig. 1] 7. Slide the CANOPY (11) and the THREADED RING (15) up the CHAIN (14). Place the CANOPY (11) over the OUTLET BOX (1) and secure it by screwing the THREADED RING (15) onto the SCREW COLLAR LOOP (13). [See Fig. 1]
# 35193-WP
GENERAL
ASSEMBLY AND INSTALLATION
CAUTION
FIG. 2
ASSEMBLY AND INSTALLATION (Continued)
8. Secure SHADE (22) to FIXTURE (16) with DECORATIVE NUTS (18) and SHADE SCREWS (24). 9. Attach THREADED ROD (23) to the bottom of the FIXTURE (16) and secure with the (uppermost) HEX NUT (23). Install bulbs, MAXIMUM 60W each. 10. Slide the DIFFUSER PLATE (26) [clear side up] over the THREADED ROD (23). Next, slide the RUBBER WASHER (25) over the THREADED ROD (23). Secure DIFFUSER PLATE (26) with the other HEX NUT (27). (Do NOT overtighten.) Attach
the FINIAL (28).
[See Fig. 2]
INSTALLATION IS NOW COMPLETE
3-LIGHT PENDANT
FIG. 1
WINTON
Customer Service: 1 [phone]
1. OUTLET BOX (NOT INCLUDED) 2. MOUNTING STRAP 3. OUTLET BOX SCREWS and WASHERS (pre-attached to outlet box) 4. BLACK SUPPLY WIRE (not included) 5. SMOOTH FIXTURE LEAD WIRE 6. WHITE SUPPLY WIRE (not included) 7. RIBBED FIXTURE LEAD WIRE 8. SUPPLY GROUND WIRE (not included) 9. FIXTURE GROUND WIRE 10. WIRE CONNECTORS 11. CANOPY 12. THREADED ROD (pre-attached) 13. SCREW COLLAR LOOP (pre-attached) 14. CHAIN 15. THREADED RING (pre-attached)
16. FIXTURE 17. FIXTURE LOOP 18. DECORATIVE NUTS (pre-attached) 19. CONNECTING CHAIN LINKS (pre-attached to chain) 20. GROUND SCREW (pre-attached) 21. HEX NUTS (pre-attached) 22. SHADE 23. THREADED ROD and HEX NUT 24. SHADE SCREWS 25. RUBBER WASHER 26. DIFFUSER PLATE 27. HEX NUT 28. FINIAL
8
13
10
6
4
9
2
3
20
21
19
7
5
1
11
21
14
15
12
GND
16
17
22
23
18
24
26
27
25
28