Installation Guide

ManualsBrandsCraftmade ManualsCeiling LightsRaleigh 18.5-in Old Bronze Traditional Incandescent Semi-flush Mount Light

ASSEMBLY AND INSTALLATION

1. Take the parts out of the mounting package . Screw the end of the NIPPLE (4) into the center hole of the

MOUNTING BRACKET (2) and thread both 1/8” IPS HEX NUT(5) several turns onto each end of the

NIPPLE(4) but do not tighten the 1/8” IPS HEX NUTS (5). Pull the SUPPLY WIRES (9 & 11) and the

SUPPLY GROUND WIRE (8) out from the OUTLET BOX (1) and attach the MOUNTING BRACKET (2)

assembly to the OUTLET BOX (1) using the slotted holes of the MOUNTING BRACKET (2) and the

MOUNTING SCREWS (3) provided. (See Fig. 1)

2. Thread the SCREW COLLAR LOOP (6) onto the bottom end of the NIPPLE (4). Place the CANOPY (15)

over the OUTLET BOX (1) and adjust the SCREW COLLAR LOOP (6) and NIPPLE (4) until the midpoint of

the outside threads on the SCREW COLLAR LOOP (6) is centered (aligned) with the surface of the CANOPY

(15). Remove the CANOPY (15) and tighten both 1/8” IPS HEX NUTS (5) down on the MOUNTING

BRACKET (2) and the SCREW COLLAR LOOP (6). (See Fig. 1)

3. Thread the CENTER COLUMN(23) onto the COUPLING(24), thread the FIXTURE LOOP(18) onto the

NIPPLE(19) till tight. Pull the arms so they are evenly spaced. (See Fig.2)

4. Open up the end links of the CHAIN (17) and attach one end of the CHAIN (17) onto the FIXTURE LOOP

(18). Slide the THREADED RING (16) and the CANOPY (15) onto the CHAIN (17) (in that order) and

attach the other end of the CHAIN (17) to the SCREW COLLAR LOOP (6). Close the ends of the chain links.

(See Fig. 1 and 2)

5. Unravel the fixture lead wires(10 and 12) and FIXTURE GROUND WIRE (7) and thread them through every

other link of the CHAIN (17) starting with the chain link attached to the FIXTURE LOOP (18). Feed the

fixture lead wires(10 and 12) and FIXTURE GROUND WIRE (7) through the SCREW COLLAR LOOP (6)

and NIPPLE (4) assembly. Pull the fixture lead wire(10 and 12) and the FIXTURE GROUND WIRE (7)

upward to remove any excess slack. (See Fig. 1)

6. Attach the power supply wires to the fixture lead wires by connecting the BLACK SUPPLY WIRE (9) to the

SMOOTH FIXTURE LEAD WIRE (10) and the WHITE SUPPLY WIRE (11) to the RIBBED FIXTURE

LEAD WIRE (12). Loop the FIXTURE GROUND WIRE (7) around the GROUND SCREW (14) of the

MOUNTING BRACKET (2). (Note: Be sure to provide an extra 3” length of the GROUND WIRE(7).)

Connect the remaining FIXTURE GROUND WIRE (7) to the SUPPLY GROUND WIRE (8) using a WIRE

CONNECTOR (13). Place wiring and connections inside the OUTLET BOX (1). (See Fig. 1)

ASSEMBLY AND INSTALLATION (Continued)

7. Slide the CANOPY (15) and the THREADED RING(16) up the CHAIN(17). Place the CANOPY (15)

over the OUTLET BOX (1) and secure it in place by screwing the THREADED RING (16) onto the

SCREW COLLAR LOOP (6). (See Fig.1)

8. Screw light bulbs into the lamp sockets and make sure they do not exceed the maximum wattage specified

on the fixture’s wattage rating label,

MAXIMUM 60W.

9. Thread the NIPPLE(26) onto the CLUSTER ASSEMBLY(25), secure with the hex nut, slide the

PLATE(27), GLASS SHADE(28), RUBBER WASHER(29), GASKET(30) over the NIPPLE(23) in

place, secure with the HEX NUT(31). Slide the BOTTOM FONT(32) over the NIPPLE(26), fix with the

FINIAL(33). (See Fig.2)

INSTALLATION IS NOW COMPLETED

ASSEMBLY & INSTALLATION

INSTRUCTIONS FOR #25333CH

Please read carefully and save these instructions, as you may need them at a later date.

GENERAL

All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If

you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician.

Remove the fixture and the mounting package from the box and make sure that no parts are missing by

referencing the illustrations on the installation instructions.

CAUTION

Turn off the main power at the circuit breaker before installing the fixture, in order to prevent possible shock.

1. OUTLET BOX

2. MOUNTING BRACKET

3. MOUNTING SCREW

4. NIPPLE

5. 1/8” IPS HEX NUT

6. SCREW COLLAR LOOP

7. FIXTURE GROUND WIRE

8. SUPPLY GROUND WIRE

9. BLACK SUPPLY WIRE

FIG. 1

FIG. 2

10. SMOOTH FIXTURE LEAD

WIRE

11. WHITE SUPPLY WIRE

12. RIBBED FIXTURE LEAD

WIRE

13. WIRE CONNECTOR

14. GROUND SCREW

15. CANOPY

16. THREADED RING

17. CHAIN

18. FIXTURE LOOP

19. NIPPLE

20. NUT SCREW

21. COVER PLATE

22. DECORATIVE NUT

23. CENTER COLUMN

24. COUPLING

25. CLUSTER ASSEMBLY

26. NIPPLE

27. PLATE

28. GLASS SHADE

29. RUBBER WASHER

30. GASKET

31. HEX NUT

32. BOTTOM FONT

33. FINIAL

Summary of content (2 pages)

PAGE 1
ASSEMBLY AND INSTALLATION (Continued) 7. ASSEMBLY & INSTALLATION INSTRUCTIONS FOR #25333CH Slide the CANOPY (15) and the THREADED RING(16) up the CHAIN(17). Place the CANOPY (15) over the OUTLET BOX (1) and secure it in place by screwing the THREADED RING (16) onto the SCREW COLLAR LOOP (6). (See Fig.1) 8. Screw light bulbs into the lamp sockets and make sure they do not exceed the maximum wattage specified on the fixture’s wattage rating label, MAXIMUM 60W. 9.
PAGE 2
FIG ASSEMBLY & INSTALLATION IN STRUCTION FOR #25333SF Please read carefully and save these instructions, as you may need them at a later date. CAUTION Turn off the main power at the circuit breaker before installing the fixture, in order to prevent possible shock. GENERAL All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician.