Installation Guide

YORKTOWN #35041-OBG / #35041-PLN
Please read carefully and save these instructions, as you may need them at a later date.
Turn off the main power at the circuit breaker before installing the fixture in order to
prevent possible shock.
All electrical connections must be in accordance with local and National Electrical Code
(N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections obtain the
services of a qualified electrician.
Remove all parts and hardware from the box and make sure that none are missing by
referencing the illustrations provided.
1. Pull the SUPPLY WIRES (4 & 6) and the SUPPLY GROUND WIRE (9) out from the OUTLET BOX (1)
(not included) and attach the MOUNTING STRAP (2) assembly to the OUTLET BOX (1) using the slotted
holes of the MOUNTING STRAP (2) and the OUTLET BOX SCREWS and WASHERS (3). [See Fig. 1]
2. Remove the THREADED RING (15) from the SCREW COLLAR LOOP (13) and set aside.
3. Unravel the FIXTURE LEAD WIRES (5 & 7) and FIXTURE GROUND WIRE (8). Open CONNECTING
CHAIN LINK (18) on one end of CHAIN (14) to attach CHAIN (14) to the FIXTURE LOOP (17). Close
CONNECTING CHAIN LINK (18). Thread the FIXTURE WIRES (5, 7 & 8) through every other link of
the CHAIN (14) starting with the link attached to the FIXTURE LOOP (17). Slide the THREADED RING
(15) and the CANOPY (11) (in that order) onto the CHAIN (14) and FIXTURE WIRES (5, 7, & 8). Open
CONNECTING CHAIN LINK (18) on the other end of CHAIN (14) to attach CHAIN (14) to SCREW
COLLAR LOOP (13). Close CONNECTING CHAIN LINK (18). [See Fig. 1 & 2]
4. Feed the FIXTURE LEAD WIRES (5 & 7) and FIXTURE GROUND WIRE (8) through the SCREW
COLLAR LOOP (13) and THREADED ROD (12). Pull the FIXTURE LEAD WIRES (5 & 7) and the
FIXTURE GROUND WIRE (8) upward to remove any excess slack. [See Fig. 1]
5. Attach the power supply wires to the fixture lead wires by connecting the BLACK SUPPLY WIRE (4) to
the SMOOTH FIXTURE LEAD WIRE (5) and the WHITE SUPPLY WIRE (6) to the RIBBED
FIXTURE LEAD WIRE (7). Loop the SUPPLY GROUND WIRE (8) around the GROUND SCREW
(19) of the MOUNTING STRAP (2). [Note: Be sure to provide an extra 3in. length of the SUPPLY
GROUND WIRE (9) for connection to the FIXTURE GROUND WIRE (8).] Connect the remaining
SUPPLY GROUND WIRE (9) to the FIXTURE GROUND WIRE (8). Use a WIRE CONNECTOR (10)
for all wire connections. Push wiring and connections inside the OUTLET BOX (1). [See Fig. 1]
6.
Place the CANOPY (11) over the OUTLET BOX (1) and secure it by screwing the THREADED
RING (15) onto the SCREW COLLAR LOOP (13). [See Fig. 1]
GENERAL
ASSEMBLY AND INSTALLATION
CAUTION
PENDANT
1. OUTLET BOX (NOT INCLUDED)
2. MOUNTING STRAP
3. OUTLET BOX SCREWS and WASHERS
(pre-attached to outlet box)
4. BLACK SUPPLY WIRE (not included)
5. SMOOTH FIXTURE LEAD WIRE
6. WHITE SUPPLY WIRE (not included)
7. RIBBED FIXTURE LEAD WIRE
8. FIXTURE GROUND WIRE
9. SUPPLY GROUND WIRE (not included)
10. WIRE CONNECTORS
11. CANOPY
12. THREADED ROD (pre-attached)
13. SCREW COLLAR LOOP (pre-attached)
14. CHAIN
15. THREADED RING
16. FIXTURE
17. FIXTURE LOOP
18. CONNECTING CHAIN LINK
(pre-attached)
19. GROUND SCREW (pre-attached)
20. DECORATIVE SCREWS
21. GLASS SHADE
Customer Service: 1 (800) 486-4892
1
2
20
3
FIG. 1
FIG. 2
11
19
10
4
5
6
7
9
8
12
13
14
15
17
18
21
16
7. Install bulb (not included), MAXIMUM 60W.
8. Partially loosen DECORATAIVE SCREWS (20) on FIXTURE (16). Attach GLASS SHADE (21) to
FIXTURE (16) with DECORATIVE SCREWS (20). Do NOT overtighten DECORATIVE SCREWS (20).
[See Fig. 2]
INSTALLATION IS NOW COMPLETE

Summary of content (2 pages)