Installation guide

ManualsBrandsCraftmade ManualsFanCT52

PRINTED IN CHINA

READ THESE INSTRUCTIONS AND

AND SAVE THEM FOR FUTURE USE

Federal regulations require ceiling fans

with light kits manufactured or imported

after January 1, 2009, to limit total

wattage consumed by the light kit to

190W. Therefore, this fan is equipped

with a wattage limiting device.

Installation Guide

For Models:

VG54TI2

VG54FB2

Table of Contents:

Safety Tips. pg. 1

Unpacking Your Fan. pg. 2

Parts Inventory. pg. 2

Installation Preparation. pg. 3

Hanging Bracket Installation. pg. 3

Fan Assembly. pgs. 4 - 5

Wiring. pg. 6

Canopy Assembly. pg. 7

Blade Assembly. pg. 7

Light Assembly (Optional). pg. 8

Automated Learning Process./

Activating Code. pg. 9

Wall Control Operation. pg. 9

Remote Control Operation. pg. 10

Testing Your Fan. pg. 10

Troubleshooting. pg. 11

Warranty. pg. 11

Parts Replacement. pg. 11

net weight of fan: 17.70 lb (8.03 kg)

E206035

Summary of content (24 pages)

PAGE 1
READ THESE INSTRUCTIONS AND AND SAVE THEM FOR FUTURE USE Federal regulations require ceiling fans with light kits manufactured or imported after January 1, 2009, to limit total wattage consumed by the light kit to 190W. Therefore, this fan is equipped with a wattage limiting device. Installation Guide For Models: VG54TI2 VG54FB2 E206035 net weight of fan: 17.70 lb (8.03 kg) Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg.
PAGE 2
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2. 3. 4.
PAGE 3
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. a b a. canopy. 1 piece b. hanging bracket (pre-attached to canopy). 1 piece d c e c. 16 in. downrod and hanging ball (with pin & clip). 1 piece g d.
PAGE 4
12 ft. - 20 ft. (3.66 m - 6.1 m) 3. Installation Preparation. blade edge To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 7 feet (2.13 m) from the floor and 30 in (76 cm) from any wall or obstruction. This fan is suitable for room sizes up to 400 square feet (37.2 square meters). 30 7 feet inches (2.13 m) (76 cm) 12 ft. - 20 ft. (3.66 m - 6.
PAGE 5
. Fan Assembly If you wish to extend the hanging length of your fan, you must remove the hanging ball from the 16-inch downrod provided to use with an extended downrod (sold separately). [If you wish to use the 16-inch downrod, please proceed to instructions following the dotted line below.] To remove hanging ball, loosen set screw on hanging ball and remove pin and clip. Lower hanging ball and remove stop pin.
PAGE 6
5. Fan Assembly. (cont.) safety cable loop With the hanging bracket secured to the outlet box and able to support the fan, you are now ready to hang your fan. Grab the fan firmly with two hands. Slide downrod through opening in hanging bracket and let hanging ball rest on the hanging bracket. Turn the hanging ball slot until it lines up with the hanging bracket tab.
PAGE 7
6. Wiring CAUTION: Be sure outlet box is properly grounded and that a ground wire (GREEN or Bare) is present. ground (green or bare) white supply wire black supply wire Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code. If you are unfamiliar with electrical wiring or if the house/building wires are different colors than those referred to in the diagram to the right, please use a qualified electrician.
PAGE 8
antenna hanging bracket 7. Canopy Assembly. Raise canopy to hanging bracket and align slotted holes in canopy with loosened screws in hanging bracket. Twist canopy to lock. Re-insert screws that were previously removed (on page 3, Section 4) and secure all screws with Phillips screwdriver. canopy *Remember that antenna for remote control receiver must rest outside of hanging bracket. 8. Blade Assembly.
PAGE 9
. Light Assembly (Optional). If you wish to use your fan WITH the light kit, install the halogen bulb, type JD E11, 50 watts max., provided. motor housing Tip: Do not touch glass portion of bulb with fingers or hands. Oil from skin can cause bulb to overheat and go out prematurely. Use cardboard box or foam wrapping bulb was packed with to layer around glass portion of bulb. Align grooves on glass shade with notches on light kit fitter. Turn glass shade to the RIGHT to attach glass shade.
PAGE 10
. Automated Learning Process./Activating Code. CAUTION: The remote control transmitter can be programmed to multiple receivers or fans. If this is not desired, turn wall switch off to any other programmable receiver or fan. transmitter (back) code switches Remove battery cover on back side of remote control transmitter. Use a ballpoint pen or a small screwdriver to set the code switches 1 through 4 for the transmitter. Use the same number sequence used when wiring the wall control in Section 6.
PAGE 11
12. Remote Control Operation. HI button - turns fan to HIGH speed MED button - turns fan to MEDIUM speed LOW button - turns fan to LOW speed button - turns fan OFF button - pushing button turns light ON/OFF; pressing button and holding it down for more than 0.7 seconds converts it into a dimmer 13. Testing Your Fan. It is recommended that you test fan before finalizing installation. Restore power from circuit box and light switch (if applicable).
PAGE 12
Troubleshooting. WARNING: Failure to disconnect power supply prior to troubleshooting any wiring issues may result in serious injury. Problem: Fan fails to operate. Solutions: 1. Check power to wall switch/wall control. 2. Check to be sure code switches in remote control transmitter and wall control are set properly. 3. Verify that receiver is wired properly. 4. Verify that wall control is wired properly. 5. Check to be sure fan is wired properly. 6.
PAGE 13
PAGE 14
PAGE 15
PAGE 16
PAGE 17
PAGE 18
PAGE 19
PAGE 20
PAGE 21
PAGE 22
PAGE 23
PAGE 24