Bloom Ceiling Fan BL52 Installation Instructions Instrucciones de instalación Instructions d’installation
1 Read and Save These Safety Precautions 1. Turn off electricity at main switch before wiring or servicing fan in order to avoid possible electrical shock. 2. All wiring must be in accordance with the National Electric Code (ANSI/NFPA70-1999) and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3.
2 Before Assembly 1. Make sure that the fan voltage (120) is compatible with your own electrical system. 2. Check to make sure that your carton contains all the parts mentioned in the parts list. NOTE: The box can be used as a work space to prevent any damage on the ornamental surface. CAUTION: Before installing, choose a location for mounting the fan where the blades have at least 7 feet of clearance from all objects and floor.
3 Turn off circuit breakers and wall switch to the fan supply line leads. Preparation Important: When using an existing outlet box, be sure the box is securely attached to the building structure and can support the full weight of the fan. Failure to do so can result in serious injury or death. b.) Angle Mount 7BVMUFE $FJMJOHT B %PXOSPE .PVOU /PSNBM $FJMJOHT IMPORTANT: If using the angle mount method, check to make sure the ceiling angle is not steeper than 35º.
4 Installing Mounting Bracket Support Beam “J” Hook (S8) Outlet Box (A) Ceiling OUTLET BOX Mounting Bracket (1) Bracket Screws & Washers (S3) Wood Screws (S1) Wood Screws (S1) Canopy Screws (S2) NOTE: Do not mount directly to sheet rock or ceiling tile. Prior to securing mounting bracket, screw "J" hook (S8) into ceiling outlet box as a secondary support means. Secure mounting bracket (#1) to the outlet box (A) by tightening bracket screws & washers (S3) as shown.
5 Unscrew and remove motor housing washer and motor housing top plate. Attach Large Pedal Blades from Top of Motor Housing.
6 Reattach the Motor housing Plate and Motor Housing Washer as shown. Make sure the antenna wire is threaded through hole on top of motor housing. Downrod Assembly Locate downrod assembly (#2). Loosen ball screw on black hanging ball to free lock pin. Black hanging ball will slide down. Remove ground screw and green ground wire. Remove hanging ball from downrod and save all parts.
7 Insert fan wires through downrod. Thread the downrod onto the motor housing making sure the wires don’t get twisted. Insert safety bolt (S7) through flange & downrod and attach nut. Tighten firmly. Tighten set screw (A) against downrod.
8 Place flange cover (4) over downrod assembly. Attach antenna wire to flange cover. Place canopy screw cover over downrod. Place canopy (3) over downrod (2). WARNING: Failure to completely tighten downrod as described in steps above could result in the fan loosening and possibly falling. Replace hanging ball, insert hanging pin through downrod and tighten set screw "C" in hanging ball into downrod.
9 Lift fan onto the mounting bracket (#1). Turn housing until hanging ball seats itself into ball socket (listen for click). For added security, attach safety cable from fan unit to "J" hook (S8) in outlet box. Secure by looping zip tie (S9) through safety cable and "J" hook. Tighten zip tie securely. WARNING: To reduce the risk of fire, electric shock or personal injury, mount so outlet box marked "acceptable for fan support" and use mounting screws provided with the outlet box.
10 Ground White (Neutral) Wire Connectors (S6) Black (Power) White Ground (Green) Black Blue Outlet Box Ground (Green) Downrod Ground (Green) Mounting Bracket Ground (Green) 1. Connect fan wires to ceiling wires: white fan wire to white outlet wire, black to black and green to green. Wire connectors (S6) are provided for your convenience. If an additional blue wire is present then also connect the blue wire to the black wire. (Optional light kit may be wired to individual wall switches, if desired.
11 Attach canopy (3) to the mounting bracket by placing screws (S2) into slot in canopy. Twist clockwise to lock into place. Tighten screws firmly. Seat the canopy screw cover into slots and twist to lock.
12 Slide the small pedal blades into place, support and attach with screws. (S4) Screw in candelabra light bulbs. (not included) Place light kit glass over bulbs twist to lock into place.
Remote Control Operation Instructions ON/OFF For emergency shut off. HIGH MEDIUM LOW Controls fan motor speed. To select desired speed, press button once and release. REVERSE Controls direction of fan blades. To reverse fan blades, press once and release. FAN OFF Turns fan motor speed off. Press once to turn off. To start motor speed again, hit one of the motor speed buttons. L-1 Controls no function on this fan. L-2 Controls the on/off and intensity for optional light kit.
