Installation Guide

IMPORTANT! PLEASE READ:
All Craftmade solid brass and cast aluminum lanterns are prepared with a durable
lacquer finish or a powder-coated/painted finish. Please note that the brass finish or
painted finish on exterior lanterns will weather or tarnish over time, depending upon
the environmental conditions where the lantern is installed. Your proper care of
lanterns (see below) will enhance both the life and appearance of the lanterns. Post
treatments, such as clear lacquer, are not recommended.
PROPER CARE
In order to maximize the appearance of a Craftmade brass lantern, it is important that
dust and debris is removed from the surface of the lantern periodically. It is
recommended that the lanterns be wiped down weekly using a soft, dry or damp cloth.
DO NOT use any abrasives such as car wax, brass cleaners or other polishes, glass
cleaners or chemicals, as this will scratch/remove/damage the protective coating,
allowing moisture and pollutants to come in contact with the brass, which will result in
discoloration and pitting.
ALL Craftmade cast aluminum lanterns receive a durable powder coat finish, which
enhances the durability of the lantern. This finish should also be wiped down weekly
with a soft, dry or damp cloth to remove the dust and debris that will accumulate on the
surface. DO NOT use any abrasives such as car wax, brass cleaners or other polishes,
glass cleaners or chemicals as this may damage the finish.
FAILURE TO FOLLOW THE ABOVE CARE INSTRUCTIONS WILL VOID THE
WARRANTY OF THE LANTERN.
For information regarding replacement parts, please write to:
Craftmade, P.O. Box 1037, Coppell, TX 75019
IMPORTANT: Our ballast is replaceable, but this needs to be done by a qualified
electrician without cutting the wires.
LIMITED WARRANTY
Craftmade warrants against defects in materials or workmanship for a minimum of
TWO (2) YEARS from date of purchase for use, and agrees to repair or, at our option,
replace a defective unit without charge. Brass finish is covered 90 days from purchase
date.
IMPORTANT: This Warranty does not cover damage resulting from accident, misuse
or abuse, lack of reasonable care (see above), the affixing of any attachment not
provided with the product, alteration of any attachments factory installed, loss of parts
or subjecting the fixture to any but the specified electrical service. This warranty does
not cover failure of bulbs due to accidents, abuse, misuse, vandalism, power surges, and
acts of nature such as lightning damage or any bulbs purchased separately and installed
by the consumer or any damage to the fixture caused by a separately purchased bulb.
No responsibility is assumed for any special incidental or consequential damages.
Damages occurring during transit are not covered by this warranty.
To obtain warranty service, mail sales receipt as proof of purchase-date, and a brief
explanation of the nature of the defect, to P.O. Box 1037, Coppell, TX 75019. You will
receive, by mail, a Return Goods Authorization number issued by Craftmade, and
returned freight prepaid.
For Installation or Technical Support, call 1-800-486-4892, 8 a.m. - 5 p.m., Central Time,
Monday-Friday.
Please send the following information…
1. The Model Number and Finish – Polished, Antique, White, etc.
2. The name of the part – if you have a parts problem.
3. Your name, mailing address and phone number
(with area code).
Desechar
Tuerca
hexagonal
Retirar
Instalar
Niple
roscado
corto
Niple
roscado
largo
Cola
Conjunto de fuente
Punta inferior
Tuerca hexagonal
Agujero de goteo
Punta inferior
Agujero de goteo
Monte el Farol en la Pared
Retire la punta inferior, el conjunto
de fuente, el tornillo corto
(deséchelo) y la tuerca hexagonal.
Vuelva a instalar la tuerca
hexagonal, luego el tornillo largo, la
cola, el conjunto de fuente con el
“agujero de goteo” hacia abajo.
Sujete con la punta inferior como se
ilustra.
Instalación del ensamblaje de
cola opcional
Monte de pared
Caulk
Enmasillado
Placa posterior
E6
S3
Bombilla
Tornillos
de montaje
Tapa
superior
Travesaño
Tornillo central
Enrosque la tapa
a. Inserte los cables nuevamente en la caja eléctrica.
b. Instale el farol en el travesaño y sujételo con las tuercas de
casquete como se ilustra.
c. Para prevenir que entre la humedad dentro de la caja de la toma y cause un
corto circuito, use masilla transparente para delinear el exterior de la placa
posterior del farol donde se encuentra con la pared dejando un espacio en la
parte inferior para dejar que escape la humedad.
d. Para poner una bombilla, retire los tornillos de montaje, retire la tapa,
inserte la bombilla y vuelva a colocar la tapa.