Installation Guide

Craftmade • P.O. Box 1037 • Coppell, TX USA • 75019
10-2004
IMPORTANT! PLEASE READ:
All Craftmade solid brass and cast aluminum lanterns are prepared with a durable lacquer finish
or a powder-coated/painted finish. Please note that the brass finish or painted finish on exterior
lanterns will weather or tarnish over time, depending upon the e nvironmental conditions where
the lantern is installed. Your proper care of lanterns (see below) will enhance both the life and
appearance of the lanterns. Post treatments, such as clear lacquer, are not recommended.
PROPER CARE
In order to maximize the appearance of a Craftmade brass lantern, it is important that dust and
debris is removed from the surface of the lantern periodically. It is recommended that the lanterns
be wiped down weekly using a soft, dry or damp cloth.
DO NOT use any abrasives such as car wax, brass cleaners or other polishes, glass cleaners or
chemicals, as this will scratch/remove/damage the protective coating, allowing moisture and
pollutants to come in contact with the brass, which will result in discoloration and pitting.
ALL Craftmade cast aluminum lanterns receive a durable powder coat finish, which enhances the
durability of the lantern. This finish should also be wiped down weekly with a soft, dry or damp
cloth to remove the dust and debris that will accumulate on the surface. DO NOT use any abrasives
such as car wax, brass cleaners or other polishes, glass cleaners or chemicals as this may damage
the finish.
FAILURE TO FOLLOW THE ABOVE CARE INSTRUCTIONS WILL VOID THE WARRANTYOF THE LANTERN.
For information regarding replacement parts, please write to:
Craftmade, P.O. Box 1037, Coppell, TX 75019
LIMITED WARRANTY
Craftmade warrants against defects in materials or workmanship f or a period of TWO (2) YEARS
from date of purchase for use, and agrees to repair or, at our option, replace a defective unit without
charge. Brass finish is covered 90 days from purchase date.
IMPORTANT: This Warranty does not cover damage resulting from accident, misuse or abuse,
lack of reasonable care (see above), the affixing of any attachment not provided with the product,
alteration of any attachments factory installed, loss of parts o r subjecting the fixture to any but the
specified electrical service. This warranty does not cover failu re of bulbs due to accidents, abuse,
misuse, vandalism, power surges, and acts of nature such as lightning damage or any bulbs
purchased separately and installed by the consumer or any damage to the fixture caused by a
separately purchased bulb.
No responsibility is assumed for any special incidental or consequential damages. Damages
occurring during transit are not covered by this warranty.
To obtain warranty service, mail sales receipt as proof of purchase-date, and a brief explanation of
the nature of the defect, to P.O. Box 1037, Coppell, TX 75019. You will receive, by mail, a Return
Goods Authorization number issued by Craftmade, and returned freight prepaid.
For Installation or Technical Support, call 1-800-486-4892, 8 a.m. - 5 p.m., Central Time,
Monday-Friday.
Please send the following information…
1. The Model Number and Finish – Polished, Antique, White, etc.
2. The name of the part – if you have a parts problem.
3. Your name, mailing address and phone number (with area code).
If fixture does not work:
1. Turn off electrical power and check all wire connections.
2. Check fuse or circuit breaker and change if necessary.
3. Check to make sure light bulb is in working order.
4. Ensure that dimmer switch is in the "on" position.
Troubleshooting
Printed in China
Instructions de montage
des lampadaires extérieurs
Câblage de l’alimentation du lampadaire
a. Veiller à consulter la réglementation électrique locale avant de commencer
les travaux électriques.
b. Relier la source de courant à l’emplacement du lampadaire par des fils
acheminés dans un conduit conforme à la réglementation locale.
c. Prolonger les fils d’au moins 2,50 mètres (100 po) à l’extrémité du conduit
à l’emplacement du lampadaire pour permettre le câblage de la ou des
têtes du lampadaire.
Guide
G
Couper le courant
Toujours couper le courant au tableau électrique ou débrancher le fusible
lors de l’installation ou de la réparation de tout autre appareil électrique.
LA PRÉSENCE
DE COURANT
PEUT CAUSER
DES
BLESSURES
GRAVES, VOIRE
MORTELLES
ATTENTION
Assemblée
Le temps de montage est de 35 minutes environ
EMPLACEMENT D’INSTALLATION
Choix d’un emplacement d’installation
Tenir compte des éléments suivants lors du choix d’un emplacement
d’installation :
• Ne pas implanter le lampadaire à moins de 4,9 m (16 pi) de la paroi
intérieure d'une piscine.
• Éviter d’implanter le ampadaire trop près des allées pour l’empêcher
d’être endommagé par les voitures.
• Tournevis Cruciforme
• Tournevis plat
• Ampoule(s)
• Niveau de maçon
• Clé à molette
–
OUTILLAGE NÉCESSAIRE
–
ou ou
18W/840
ou