Operator’s Manual PRO L SERIES ZERO-TURN RIDER WITH SMART LAWN TECHNOLOGY Model Nos. 247.27050*, 247.27052* & 247.27054* * -- Last digit of model number varies 5 6 Safe Operation Practices..................................................2 Slope Gauge....................................................................6 Assembly........................................................................7 Smart Lawn Activation................................................... 10 Operation....................
SAFETY INSTRUCTIONS WARNING DANGER This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol, HEED ITS WARNING! This machine was built to be operated according to the safe operation practices in this manual.
SAFETY INSTRUCTIONS • • • • CHILDREN Your machine is designed to cut normal residential grass of a height no more than 10”. Do not attempt to mow through unusually tall, dry grass (e.g., pasture) or piles of dry leaves. Dry grass or leaves may contact the engine exhaust and/or build up on the mower deck presenting a potential fire hazard. Use only accessories and attachments approved for this machine by the machine manufacturer.
SAFETY INSTRUCTIONS • • • • • • • • • • Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device. Extinguish all cigarettes, cigars, pipes and other sources of ignition. Never fuel machine indoors. Never remove gas cap or add fuel while the engine is hot or running. Allow engine to cool at least two minutes before refueling. Never over fill fuel tank.
SAFETY INSTRUCTIONS SAFETY SYMBOLS This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR’S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate DANGER — ROTATING BLADES Never carry passengers. Never carry children, even with the blades off.
Figure 1 ashed 15° d line Figure 2 (TOO STEEP) Slopes are a major factor related to tip-over and roll-over accidents which can result in severe injury or death. Do not operate machine on slopes in excess of 15 degrees. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it. Always mow across the face of slopes, never mow up and down the face of slopes.
ASSEMBLY Set-Up Install Operator’s Seat NOTE: Remove the deck wash system nozzle adapter from the manual bag and store for future use. To install the seat proceed as follows: Moving The Riding Mower Manually 1. NOTE: The seat is shipped with the seat switch and seat pan attached. Your riding mower’s transmission is equipped with a hydrostatic relief valve for occasions when it is necessary to move the riding mower manually.
ASSEMBLY Position Drive Control levers Connecting the Battery Cables The drive control levers of the riding mower are lowered for shipping purposes. The flange lock nuts, hex screws, and flat washers that normally secure the control levers in their operating position are unfastened and installed in the slotted holes of the control levers for shipment. The control levers must be repositioned to operate the riding mower. To reposition the control levers for operation, proceed as follows: 1.
ASSEMBLY Lower Deck Discharge Chute Deflector Checking Tire Pressure WARNING WARNING Never operate the mower deck without the chute deflector installed and in the down position. Do not overinflate tires. Check sidewall of tires for maximum psi. Equal tire pressure should be maintained at all times. The discharge chute deflector must be installed before operating the mower. 1. Remove the keys that are attached with a zip tie to the chute bracket. 2.
ASSEMBLY Adjusting the Seat Adding Fuel To adjust the position of the seat, rotate the seat forward and locate the two adjustment knobs on the front of the seat pan. Refer to Figure 8. WARNING Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the riding mower indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition. 1. Be sure engine is outdoors and in a well-ventilated area. 2.
OPERATION LH Control Lever RH Control Lever Deck Lift Handle Deck Height Index Throttle Control Choke Control Cup Holder LCD Service Minder & Hour Meter PTO Knob Ignition Switch Module Fuel Tank Cap Fuel Level Window RH Transmission Bypass Rod LH Transmission Bypass Rod Now that you have set up your riding mower, it’s important to become acquainted with its controls and features. Refer to Figure 9.
OPERATION Choke Control Power Take-Off (PTO) Knob The choke control is located on the RH console .The choke control determines the position of the engine choke. Pull the knob out to choke the engine; push the knob in to open the choke. The PTO knob is located on the RH console to the left of the hour meter/indicator panel. The PTO knob operates the electric PTO clutch mounted on the bottom of the engine crankshaft.
OPERATION LCD Service Minder & Hour Meter w/ Smart Lawn App Bluetooth® Activation When the ignition key is rotated out of the STOP position but not into the START position, the LCD Service Minder and Hour Meter will briefly display the battery voltage, followed by the tractor’s accumulated hours. NOTE: Hours of tractor operation are recorded only when the engine is running. If the riding mower is equipped with headlights, the lights will remain on until the riding mower is turned off.
OPERATION Checking the Safety Interlock Circuits 12. Lubricate all pivot points listed in the Service and Maintenance section. Periodically check the safety interlock circuits to ensure they are working properly. If a safety circuit is not working as designed, contact your authorized service dealer to have the tractor inspected. DO NOT operate the tractor if any safety circuit is not functioning properly. To check the safety circuits, proceed as follows: 13.
OPERATION NOTE: Do NOT leave the throttle/choke control (if equipped) or choke control (if equipped) in the CHOKE position while operating the tractor. Doing so will result in a “rich” fuel mixture and cause the engine to run poorly. Practice Operation (Initial Use) Cold Weather Starting Operating a zero-turn tractor is not like operating a conventional type riding tractor. Although and because a zero turn tractor is more maneuverable, getting used to operating the control levers takes some practice.
OPERATION 3. Move the throttle control lever (if equipped) or throttle/choke control lever forward to the full throttle position. Turning the Tractor While Driving Forward WARNING NOTE: Although the tractor’s engine is designed to run at full throttle, when performing a practice session the tractor must be operated at less than full throttle. This only applies to practice. When reversing the direction of travel, we recommend performing gradual ‘U’ turns where possible.
OPERATION 3. The greater the fore-to-aft distance between the two levers, the sharper the tractor will turn. 4. To execute a “pivot turn,” move the turn side drive control lever to the neutral position, while moving the other control lever forward. NOTE: Making a “pivot turn” on grass will greatly increase the potential for defacement of the turf. Turning While Driving Rearward To turn the tractor while driving rearward, move the control levers as necessary so that one lever is forward of the other.
OPERATION Reverse Caution Mode Executing a Zero Turn The REVERSE CAUTION MODE position of the key switch module allows the tractor to be operated in reverse with the blades (PTO) engaged. WARNING When executing a zero turn, the tractor MUST BE STOPPED. Executing a zero turn while th e tractor is moving can significantly reduce your control of the tractor and will cause severe turf defacement to occur. NOTE: Mowing in reverse is not recommended.
OPERATION Executing a “Y” Maneuver Driving On Slopes For low traction conditions, follow these procedures for zero turns (the “Y-maneuver”): Refer to the slope gauge in the Safe Operation Section to help determine slopes where you may not operate safely. To turn clockwise (front of machine moves toward RIGHT) when traveling FORWARD: WARNING Do not operate on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1⁄2 feet every 10 feet).
OPERATION 6. When approaching the other end of the strip, slow down or stop before turning. A U-turn is recommended unless a pivot or zero turn is required. 7. Align the mower with an edge of the mowed strip and overlap approximately 3”. 8. Direct the tractor on each subsequent strip to align with a previously cut strip. 9. To prevent rutting or grooving of the turf, if possible, change the direction that the strips are mowed by approximately 45° for the next and each subsequent mowing.
SERVICE AND MAINTENANCE MAINTENANCE SCHEDULE WARNING Before performing any type of maintenance/service, disengage all controls and stop the engine. Wait until all moving parts have come to a complete stop. Disconnect spark plug wire and ground it against the engine to prevent unintended starting. Always wear safety glasses during operation or while performing any adjustments or repairs. Interval Each use Follow the maintenance schedule given below. This chart describes service guidelines only.
SERVICE AND MAINTENANCE 7. WARNING Before performing any maintenance or repairs, disengage the PTO, move the drive control levers fully outward in the neutral position, engage the parking brake, stop the engine and remove the key to prevent unintended starting. 8. Cleaning the Tractor WARNING Post-Operation Tractor Care If the tractor has been recently run, the engine, muffler and surrounding metal surfaces will be hot and can cause burns to the skin.
SERVICE AND MAINTENANCE • Storing the Tractor Clean the top of the mower deck, under the spindle covers and belt area. See Figure 24. • • Allow the machine to cool in an open area before storing. Do not park the tractor near any flammable materials (wood, cloth or chemicals) or any open flames or other potential source of ignition (furnace, water heater or any other type of heater). Remove all combustible materials from the tractor before storing. Empty cargo boxes, grass catchers or containers.
SERVICE AND MAINTENANCE Tire Maintenance General Battery Information Check the tire air pressure after every 50 hours of operation or weekly. Keep the tires inflated to the recommended pressures. Improper inflation will shorten the tire service life. See the tire side wall for proper inflation pressures. Observe the following guidelines: • Do not inflate a tire above the maximum pressure shown on the sidewall of the tire. • Do not reinflate a tire that has been run flat or seriously under inflated.
SERVICE AND MAINTENANCE 1. Remove the hex washer screw securing the battery hold-down bracket to the frame. Then flip the battery hold-down bracket up to free the battery. See Figure 28. Hex Washer Screw Servicing Electrical System A fuse is installed to protect the riding mower’s electrical system from damage caused by excessive amperage. Always use the same capacity fuse for replacement. If the electrical system does not function, check for a blown fuse.
SERVICE AND MAINTENANCE Adjustments Deck Leveling NOTE: Check the tractor’s tire pressure before performing any deck leveling adjustments. Refer to Tires for information regarding tire pressure. CAUTION Shut the engine off, remove the ignition key and engage the parking brake before making adjustments. Protect your hands by using heavy gloves when handling the blades. WARNING Shut the engine off, remove the ignition key and engage the parking brake before making adjustments.
SERVICE AND MAINTENANCE 3. Measure the distance from the front of the blade tip to the ground and the rear of the blade tip to the ground. The first measurement taken should be between 1⁄4” and 3⁄8” less than the second measurement. 4. Determine the approximate distance necessary for proper adjustment and proceed, if necessary. 5. Using a wrench, raise or lower the front of deck by turning lock nut on the front deck lift rod and secure with the rear jam nuts. See Figure 33. 2.
SERVICE AND MAINTENANCE 2. Locate the drive control lever stop adjustment bolts on the front of the seat frame. See Figure 35. 4. Releasing Belt Tension with the Idler Pulley a. Using the deck lift handle, raise the deck to the position that provides the most horizontal run of the belt between the deck idler pulleys and the PTO pulley on the bottom of the engine. See Figure 36. Transport Position/ Highest Mowing Position Deck Removal/ Installation Position Lowest Mowing Position Figure 35 3. 4.
SERVICE AND MAINTENANCE 5. 6. Rolling the Belt off the PTO Pulley a. Using the deck lift handle, raise the deck to the position that provides the most horizontal run of the belt between the deck idler pulleys and the PTO pulley on the bottom of the engine. b. Sitting behind the tractor facing forward, reach beneath the tractor to grasp the belt at the front of the PTO pulley. Locate the LH and RH deck release pins on each side of the deck.
SERVICE AND MAINTENANCE 9. Make certain the belt is in the spindle pulleys of the deck, and that the backside of the belt is against both the fixed and movable idler pulleys. 10. Sitting behind the tractor, facing forward, make certain the belt is not twisted; then reach beneath the tractor to grasp the belt and pull it toward the PTO pulley. 3. Remove the two idler pulleys by removing the hex screws, washers and flange lock nuts that secure them to the deck and the idler arm. See Figure 41.
SERVICE AND MAINTENANCE Mower Blade Care Transmission Drive Belt WARNING Before performing any maintenance, place the PTO switch in the “OFF” position, engage the parking brake lever, turn the ignition key to the “OFF” position and remove the key from the switch. Protect your hands by using heavy gloves when handling the blades. When servicing the mower deck, be careful not to cut yourself on the sharpened blades. The cutting blades must be kept sharp at all times.
OFF-SEASON STORAGE WARNING Never store garden riding mower with fuel in tank indoors or in poorly ventilated areas where fuel fumes may reach an open flame, spark, or pilot light as on a furnace, water heater, clothes dryer, or gas appliance. Riding Mower Storage If your riding mower is not going to be operated for an extended period of time (thirty days to approximately six months), the riding mower should be prepared for storage. Store the riding mower in a dry and protected location.
TROUBLESHOOTING WARNING Before performing any type of maintenance/service, disengage all controls and stop the engine. Wait until all moving parts have come to a complete stop. Disconnect spark plug wire and ground it against the engine to prevent unintended starting. Always wear safety glasses during operation or while performing any adjustments or repairs. This section addresses minor service issues. To locate the nearest Sears Service Center or to schedule service, simply contact Sears at 1-888-331-4569.
TROUBLESHOOTING Problem Engine overheats Cause Remedy 1. Engine oil level low 1. Fill engine with proper amount and type of oil. 2. Air flow restricted 2. Clean grass clippings and debris from around the engine’s cooling fins and blower housing. Engine hesitates at high RPMs 1. Spark plug gap set too close 1. Remove spark plug and adjust gap. Engine idles poorly 1. Fouled spark plug 1. Replace spark plug and adjust gap. 2. Dirty air cleaner 2.
Manual del Operador PRO L SERIE TRACTOR CON RADIO DE GIRO CERO AVEC INTELLIGENT TECHNOLOGIE CORTACÉSPED Modelo N.° 247.20420*, 247.20422* & 247.20424* * -- Último dígito del número de modelo varía 5 6 Instrucciones de seguridad.............................................36 Servicio y Mantenimiento.............................................. 55 Guía para la operación en pendientes.............................40 Almacenamiento Fuera De Temporada................................66 Montaje................
INSTRUCCIONES DE SEGURIDAD ADVERTENCIA PELIGRO La presencia de este símbolo indica que se trata de instrucciones de seguridad importantes que debe respetar para evitar poner en riesgo su seguridad personal y/o material y la de los demás. Lea y cumpla todas las instrucciones de este manual antes de intentar operar esta máquina. Si no respeta estas instrucciones puede provocar lesiones personales.
INSTRUCCIONES DE SEGURIDAD • • • • NIÑOS Su máquina está diseñada para cortar césped residencial normal de una altura no mayor a 10 pulgadas. No intente cortar césped demasiado crecido, seco (por ejemplo, pastura) ni pilas de hojas secas. El césped o las hojas secas pueden ponerse en contacto con el escape del motor y/o acumularse en la plataforma de corte constituyendo un peligro de incendio en potencia. Utilice solamente accesorios y complementos aprobados por el fabricante para esta máquina.
INSTRUCCIONES DE SEGURIDAD • En todo momento mantenga la boquilla en contacto con el borde del depósito de combustible o con la abertura del recipiente, hasta terminar la carga. No utilice un dispositivo de apertura/cierre de la boquilla, • Apague todos los cigarrillos, cigarros, pipas y otras fuentes de combustión. • Nunca cargue combustible en la máquina en un espacio cerrado. • Nunca saque la tapa del combustible ni agregue combustible mientras el motor está caliente o en marcha.
INSTRUCCIONES DE SEGURIDAD SÍMBOLOS DE SEGURIDAD En esta página se presentan y describen los símbolos de seguridad que en este producto puede tener. Lea, entienda y siga todas las instrucciones incluidas en la máquina antes de intentar armarla y hacerla funcionar. Símbolo Descripción LEA LOS MANUALES DEL OPERADOR Lea, entienda y siga todas las instrucciones incluidas en los manuales antes de intentar armarla y hacerla funcionar. PELIGRO — CUCHILLAS GIRATORIAS Nunca lleve pasajeros.
Figura 1 tinua iscon nea d 15° lí Las pendientes son un factor importante relacionado con un vuelco y renovación de los accidentes que pueden provocar lesiones graves o la muerte. No utilice la máquina en pendientes de más de 15 grados. Todos pendientes requiere mayor precaución. Si no puede retroceder en la pendiente o si se siente inseguro en ella, no la recorte. Siempre corte el césped en toda la superficie de la cuesta. Nunca arriba y abajo las pendientes.
MONTAJE Configuración Instale el asiento del operador NOTA: Retire el adaptador del pico del sistema de lavado de la plataforma de la bolsa del manual, y guárdelos para uso futuro. Para instalar el asiento proceda de la siguiente manera: Desplazamiento manual del tractor cortacésped La transmisión del tractor cortacésped está equipada con una válvula de descarga hidrostática para ocasiones en las que es necesario mover el tractor manualmente.
MONTAJE Coloque las palancas de control de la transmisión en posición Conexión de los cables de la batería Las palancas de control de la transmisión del tractor cortacésped se bajan para el envío. Las tuercas de seguridad con brida, los tornillos hexagonales y las arandelas planas que normalmente fijan las palancas de control en su posición de funcionamiento se aflojan e instalan en los orificios ranurados de las palancas de control para el envío.
MONTAJE Baje el deflector del canal de descarga de la plataforma Control de la presión de los neumáticos ADVERTENCIA ADVERTENCIA Nunca opere la plataforma de corte sin el deflector del canal de descarga instalado y en posición baja. Se debe instalar el deflector del canal de descarga antes de operar la cortadora de césped. 1. Retire las chavetas que están sujetas con una unión con cierre al soporte del canal. 2.
MONTAJE Ajuste del asiento Carga de combustible Para ajustar la posición del asiento, gírelo hacia adelante y ubique las dos perillas de ajuste en el frente del contenedor del asiento. Consulte la Figura 8. ADVERTENCIA Tenga mucho cuidado al trabajar con gasolina. La gasolina es sumamente inflamable y sus vapores pueden causar explosiones. Nunca agregue combustible al tractor cortacésped en interiores ni mientras el motor está caliente o en funcionamiento.
FUNCIONAMIENTO Palanca de control del lado derecho Palanca de control del lado izquierdo Manija de elevación de la plataforma Posicionamiento de la altura de la plataforma Control del acelerador Control del cebador Portacubeta LCD avisador de servicio y medidor horario Perilla de la toma de fuerza (PTO) Módulo de interruptor de encendido Tapón del depósito de combustible Visor del nivel de combustible Varilla de derivación de la transmisión del lado derecho Varilla de derivación de la transmisión del
FUNCIONAMIENTO Control del cebador Perilla de la toma de fuerza (PTO) El control del cebador está ubicado en la consola del lado derecho. Dicho control determina la posición del cebador del motor. Tire de la perilla hacia afuera para cebar el motor; empuje la perilla hacia adentro para abrir el cebador. La perilla de la PTO está ubicada en la consola del lado derecho, a la izquierda del medidor horario/panel indicador.
FUNCIONAMIENTO LCD avisador de servicio y medidor horario w/ Activación de Bluetooth® inteligente Césped App Cuando se gira la llave de encendido de la posición de parada, pero no a la posición de arranque, el LCD avisador de servicio y medidor horario mostrará brevemente la tensión de la batería, seguido de las horas acumuladas del tractor. NOTA: Las horas de funcionamiento del tractor cortacésped se registran únicamente cuando el motor está en marcha.
FUNCIONAMIENTO • • b. Mantenga la cortadora de césped y especialmente el motor y los componentes hidráulicos limpios y sin grasa, pasto y hojas para reducir las posibilidades de que se prendan fuego y permitir que se enfríen de forma adecuada. No llene el tanque de combustible con el motor en funcionamiento o si el mismo está caliente. Deje enfriar el motor varios minutos antes de la recarga de combustible. Apriete el tapón de combustible con firmeza. c. d.
FUNCIONAMIENTO 5. 6. NOTA: Si el motor está caliente, tal vez no sea necesario cebar el motor. Mueva el control del acelerador (si está instalado) hasta una distancia media entre las posiciones Velocidad lenta y Velocidad rápida. Gire la llave de encendido en el sentido de las agujas del reloj hasta la posición START (encendido). Una vez que arranque el motor, suelte la llave. Volverá a la posición de NORMAL MOWING (corte normal).
FUNCIONAMIENTO 3. Giro con el tractor en marcha adelante Mueva la palanca de control del acelerador (si está equipada) o la palanca de control del acelerador/cebador hacia adelante hasta la posición de aceleración máxima. ADVERTENCIA NOTA: Si bien el motor del tractor se ha diseñado para funcionar a máxima aceleración, cuando practica el tractor debe funcionar a menos del máximo. Esto se aplica únicamente al funcionamiento del motor durante la práctica.
FUNCIONAMIENTO 3. Cuanto mayor sea la distancia de adelante hacia atrás entre las dos palancas, más cerrado será el giro que dará el tractor. 4. Para realizar un "giro de pivote", mueva la palanca de control del lado de giro a la posición neutra, mientras mueve la otra palanca de control hacia adelante. NOTA: Los "giros de pivote" sobre el pasto aumentan significativamente el potencial de que se deteriore el césped.
FUNCIONAMIENTO Modo marcha atrás con precaución Giro de radio cero ADVERTENCIA La posición MODO DE PRECAUCIÓN EN MARCHA ATRÁS del módulo de la llave de contacto permite operar el tractor en marcha atrás con las cuchillas (PTO) enganchadas. Para realizar un giro de radio cero, el tractor SE DEBE DETENER. La realización de un giro de radio cero con el tractor en movimiento puede reducir significativamente el grado de control que se tenga sobre el mismo, y dará lugar a un grave deterioro del césped.
FUNCIONAMIENTO Realización de una maniobra en “Y” Operación en pendiente Cuando existen condiciones de baja tracción, realice estos procedimientos para realizar giros de radio cero (la “maniobra en Y”): Consulte indicador de pendiente en la Sección Funcionamiento Seguro para determinar en qué pendientes no puede operar el tractor de manera segura. Para girar en el sentido de las agujas del reloj (el frente de la máquina se mueve hacia el lado DERECHO) al desplazarse HACIA ADELANTE: 1.
FUNCIONAMIENTO 6. Cuando se acerque al otro extremo de la franja, reduzca la velocidad o deténgase antes de girar. Se recomienda realizar un giro en U a menos que sea necesario realizar un giro de radio cero. 7. Alinee la cortadora de césped con un borde de la franja cortada y superponga la pasada aproximadamente 3 pulgadas. 8. Oriente el tractor en cada franja subsiguiente de modo que se alinee con la franja ya cortada. 9.
SERVICIO Y MANTENIMIENTO PROGRAMA DE MANTENIMIENTO Siga el cronograma de mantenimiento que se presenta a continuación. Esta tabla sólo describe pautas de servicio. Utilice la columna Registro de Servicio para hacer el seguimiento de las tareas de mantenimiento completadas. Llame al 1-888-331-4569 para programar el servicio del servicio de piezas y reparaciones de Sears. ADVERTENCIA Antes de realizar cualquier tipo de mantenimiento o servicio, desactive todos los controles y detenga el motor.
SERVICIO Y MANTENIMIENTO 4. Abra el suministro de agua. 5. Desde el asiento del operador del tractor, encienda el motor y enganche la potencia de arranque (PTO). Deje funcionar según sea necesario. Desactive la toma de fuerza (PTO) y detenga el motor. 6. Cierre el suministro de agua. Después de la operación del tractor Cuidado 7. Tire del collarín de ajuste (a) del adaptador del pico (b) hacia atrás para desconectar el adaptador del pico (b) del pico de lavado de la plataforma (c).
SERVICIO Y MANTENIMIENTO • Almacenamiento del tractor Limpiar la parte superior de la plataforma de corte, bajo las sábanas de husillo y área de la correa. Vea la Figure 24. • • Deje que la máquina se enfríe en un área abierta antes de guardarlo. No estacione el tractor cerca de materiales inflamables (madera, tela o productos químicos) o cualquier llama abierta u otra fuente potencial de ignición (horno, calentador de agua o cualquier otro tipo de calentador).
SERVICIO Y MANTENIMIENTO 14. Información general sobre la batería Una vez que se haya terminado de drenar el aceite, reemplace el tapón de manguera de cabeza cuadrada y llene el motor como se indica en el manual del propietario del motor. Para conocer la capacidad de aceite, consulte el manual del propietario del motor que se incluye con el tractor.
SERVICIO Y MANTENIMIENTO Retiro de la batería 2. ADVERTENCIA Los postes, bornes y accesorios de la batería contienen plomo y compuestos de plomo. Lávese las manos después de estar en contacto con estos componentes. La batería está ubicada debajo del marco del asiento. Para retirar la batería: 1. Extraiga el tornillo de la arandela hexagonal que sujeta el soporte de sujeción de la batería al marco. TLuego levante el soporte de sujeción de la batería para liberar la batería. Vea la Figura 28.
SERVICIO Y MANTENIMIENTO 1. Gire el asiento del operador hacia adelante y limpie la tapa del depósito y el área que la rodea para evitar que el aceite de transmisión se contamine con residuos. Vea la Figura 30. Ajustes PRECAUCIÓN Apague el motor, retire la llave de encendido y coloque el freno de mano antes de realizar ajustes. Proteja sus manos utilizando guantes reforzados cuando manipule las cuchillas.
SERVICIO Y MANTENIMIENTO Nivelación de la plataforma intermedia. NOTA: Controle la presión de neumáticos del tractor antes de realizar cualquier nivelación de la plataforma. Consulte la sección Neumáticos para obtener información sobre la presión de los neumáticos. 5. Gire la hoja cerca posible del canal de descarga de manera que quede paralelo con el tractor.. 6.
SERVICIO Y MANTENIMIENTO 11. Retire la tuerca de seguridad que fija uno de los tornillos hexagonales de las ruedas de calibración delanteras a la plataforma. Retire la rueda de calibración, el tornillo hexagonal y el espaciador. Vea la Figura 34. 2. Ubique los pernos del ajuste de detención de las palancas de control de la transmisión que están en el frente del marco del asiento. Vea la Figura 35. Rueda Tuercas de seguridad Espaciador Tornillo hexagonal Figura 34 12.
SERVICIO Y MANTENIMIENTO 4. 5. Para aflojar la tensión de la correa con la polea loca. a. Usando la manija de elevación de la plataforma, levante la plataforma a la posición que le ofrece mayor recorrido horizontal de la correa entre las poleas locas de la plataforma y la polea de la PTO en la base del motor. Vea la Figura 36. Haciendo rodar la correa para sacarla de la polea de la toma de fuerza (PTO). a.
SERVICIO Y MANTENIMIENTO 6. Ubique los pasadores de liberación de la plataforma del lado izquierdo y del lado derecho que se encuentran a cada lado de la plataforma. Tire de los pasadores de liberación hacia afuera y suelte la plataforma de los brazos de elevación del lado derecho e izquierdo de la plataforma. Vea la Figura 39. 7.
SERVICIO Y MANTENIMIENTO 3. Cuidado de las cuchillas de la cortadora de césped Extraiga las dos poleas locas, para lo cual debe retirar los tornillos de cabeza hexagonal y las tuercas de seguridad con brida que las sujetan a la plataforma y el brazo de polea loca. Consulte la Figura 41. No afloje ningún elemento de ferretería al sacar el tornillo de cabeza hexagonal y la tuerca de seguridad con brida.
ALMACENAMIENTO FUERA DE TEMPORADA ADVERTENCIA Nunca almacene el tractor cortacésped con combustible en el tanque en un espacio cerrado o en áreas poco ventiladas donde los gases del combustible puedan llegar a una llama expuesta, una chispa o un piloto como el que tienen algunos hornos, calentadores de agua, secadores de ropa o algún artefacto a gas.
SOLUCIÓN DE PROBLEMAS ADVERTENCIA Antes de realizar cualquier tipo de mantenimiento o servicio, desactive todos los controles y detenga el motor. Espere a que se detengan completamente todas las piezas móviles. Desconecte el cable de la bujía y póngalo haciendo masa contra el motor para evitar que se encienda accidentalmente. Utilice siempre anteojos de seguridad durante el funcionamiento o mientras ajusta o repara este equipo. En esta sección se analizan problemas menores de servicio.
SOLUCIÓN DE PROBLEMAS Problema El motor recalienta Causa Solución 1. El nivel de aceite del motor está bajo. 2. Flujo de aire restringido 1. Llene el motor con cantidad y tipo de aceite adecuados. 2. Elimine los recortes de césped y los desechos de alrededor de las aletas de enfriamiento del motor y de la carcasa del soplador. El motor vacila a altas revoluciones 1. Poca separación de los electrodos de la bujía 1. Extraiga la bujía y regule la separación.