f_Save This Manual _ for Future Reference SEARS owner's manual O MODEL NO. 113.177260 \ ! - CRRFTSMRN® Serial Number Model and serial numbers may be found on the handle. You should record both model and serial numbers in a safe place for future TOOL VAC use. FOR YOUR SAFETY • assembly • operating • repair parts READ ALL INSTRUCTIONS CAREFULLY K J Sears, Roebuck and Co., Hoffrnan Estates, IL. 60179 U.S.A. Part No. SP5929 Printed in U.S.A.
FULL ONE YEAR WARRANTY ON CRAFTSMAN TOOL VAC If within one year from the date of purchase, this Craftsman Vac fails due to a defect in material or workmanship, Sears will repair it, free of charge. If this Craftsman Vac is used for commercial or rental purposes, this warranty coverage applies for only 90 days from date of purchase. Warranty Service Is Available By Simply Contacting The Nearest Sears Service Center/department Throughout The United States.
Connect toa properly grounded outlet only.Seegrounding instructions. Donotunplug bypulling oncord.To unplug, grasptheplug,notthecord. Donotusewithdamaged cord,plugor otherparts.Ifyourvacisnotworking asit should, hasmissing parts,hasbeen dropped, damaged, leftout-doors, or dropped intowater,returnittoaSears Service Center. Donotpullorcarrybycord,usecordas handle, closeadooroncord,orpullcord around sharpedgesorcorners. Donot runvacovercord.Keepcordaway from heated surfaces.
Introduction This vac is intended for household use with small hand held power tools with current rating 6 amperes or less. It may also be used for dedicated dry vacuuming jobs needed in the household.
Cage Assembly Power Head WARNING: For your own safety, never connect plug to power source outlet until all assembly steps are complete and you have read and understood the safety and operation instructions. Do not operate vac with any parts damaged or missing. NOTE: Your vac is shipped unassembled. Read the following assembly instructions carefully. 1. Grasp flexible locking tabs on both the right and left side of the power head. Place your thumbs on the drum tabs.
Filter Assembly 1. Carefully slide the filter onto the filter cage, sliding it over the center ring covering the 3 slots until the filter stops against the lid. _ Filter Nut ,,.j 2. Place the hole in the filter plate over threaded screw of the filter cage. 3. Gently push on the filter plate to seat the rubber ring of the filter inside the circular channel of the filter plate. 4. Place filter nut onto threaded screw and tighten it. Finger tighten only.
Cord and Hose Storage 1. Your vac has a convenient area to store your power cord and vac hose. Handle \ 2. Wrap the power cord around the top of the handle on the vac and attach the end of the plug to the cord. Power Cord 3.Wrap the hose around the vac as shown and group the hose together as shown in the diagram. CAUTION: A partially unwrapped cord may fall in coils near your feet. You could trip. To avoid this, always fully unwrap the cord before plugging it in.
2.Plugthecordofthehandheldpower toolintotheToolVacoutlet(located belowtheswitch). Usethe3Velcro stripssupplied withtheToolVactohold thepower cordtothevacuum hose. WraptheVelcro stripsaround thehose andcordforsafeandconvenient tool usage. Thenconnect thehandheld powertooltothevachosesupplied, by usingoneoftheadapters supplied, or Adapter #0 Adapter #1 bypurchasing theadapter thatmaybe suggested foruseintheowner's man- Suggested Wet/Dry Vac accessories for ualofyourhandheldpower tool.
Filter Maintenance WARNING: Do not remove the filter cage. It is there to help prevent your fingers from getting into the blower wheel. Cleaning Your filter should be cleaned often to maintain peak vac performance. NOTE: This filter is a two stage filter made of high quality paper designed to stop very small particles of dust. Handle the filter carefully when removing to clean or installing it.
Grounding Instructions This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. WARNING: 3-Prong Plug Properly Grounded Outlet -...
Notes 11
Repair Parts Craftsman Tool Vac Model Number 113.177260 Always order by Part Number - Not by Key Number Key No. Part No. 1 2 824275 820563-7 3 4 5 6 7 8 9 10 11 12 824259 824660 824257-1 818977 824280 818978 73316 818989-3 821814-2 STD610805 13 14 15 16 824278-1 824264-1 824256-1 824273-1 Key No. Description Cord w/Plug Screw, Pan Hd 10-32 x 3/4 Board, Control Hose, 1-1/4" x 11 Ft.
Repair Parts Craftsman Tool Vac Model Number 113.
Notes 14
Notes 15
For the repair or replacement parts you need Call 7 am - 7 pm, 7 days a week 1-800-366-PART (1-800-366-7278) For in-home major brand repair service Call 24 hours a day, 7 days a week 1-800-4-REPAIR (1-800-473-7247) For the location of a Sears Repair Service Center in your area Call 24 hours a day, 7 days a week 1-800-488-1222 For information on purchasing a Sears Maintenance Agreement or to inquire about an existing Agreement Call 9 am - 5 prn, Monday-Saturday 1-800-827-6655 SEARS II;I=;,,'.