Save This Manual For Future Reference MODEL NOS. 113,177120 113.177440 113.177460 (6-Gallon) Caster feet with storage - not on all models Serial Number Model and serial numbers may be found on the back of the motor cover, You should record both model and serial numbers in a safe :_lace for future use. WETIDRY VAC FOR YOUR SAFETY: READ ALL INSTRUCTIONS CAREFULLY _.. • assembly • operating • repair paffs J_.. Sold by SEARS, ROEBUCK AND CO., Chicago, Form No. SP5465 j IL 60684 U_S.A.
FULL ONE YEAR WARRANTY ON CRAFTSMAN WET/DRY VACS _' If within one year from the date of purchase, this Craftsman Wet/Dry Vac fails due to a defect in material or workmanship, Sears will repair it, free of U charge. If this Craftsman Wet/Dry Mac is used for commercial or rental purposes, this warranty coverage applies for only 90 days from date of purchase. WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING NEAREST SEARS SERVICE CENTER/DEPARTMENT THROUGHOUT THE THE UNITED STATES.
Donotputanyobjectintoventilation openings.Do not vacuumwith any ventilation openings blocked; keepfreeof dust,lint,hairoranything thatmayreduce airflow. Keephair,looseclothing, fingers, andall partsof bodyawayfromopenings and moving parts. Toavoidfalls, useextracarewhen cleaning onstairs. ThisWet/DryVacis double-insulated, eliminatingthe needfor a separate grounding system.Useonlyidentical replacement parts.Readtheinstructions forServicing Double-Insulated Wet/Dry Vacsbefore servicing.
Unpacking and Checking Carton Contents 0 Remove entire contents of carton. Check each item against the Carton Contents List. Notify your Sears Store immediately if any parts are damaged or missing. Carton Contents List Key Description Qty. A Vac Assembly .............................. 1 B Hose Assembly ............................ 1 C Utility Nozzle ................................ 1 *D Caster Storage ........................... 4 E Caster ........................................... 4 F Owners Manual ...
Filter Assembly - 1. Carefully put the filteronto the filter cage by sliding it over the center ring covering the 3 slots until it rests on the lid. this will deform or crack the fiffer I CAUTION: not overtighten as plate or filterDo cage. 2. Place the hole of the filter plate over threaded screw of the filter cage. 3. Gently push on the filter plate in order for the rubber ring of the filter to seat inside the circular channel of the filter. 4. Place filter nut onto threaded screw and tighten it down.
Vac Assembly ...... --- 1. Line up deflector on top portion of vac with the vacuum inlet of the drum, 2. Position the handles with flexible latches over the locking tabs on the drum. Press down on the handles until the flexible latches snap over the tabs on the drum. NOTE: Latches will not snap on if top portion of vac assembly is on backwards, or not aligned properly. 3. Push end of hose into vacuum inlet of dust drum. 4. Push rectangular hose. TopAssembly Channel = ipush Down Pu.
Vacuuming Dry Materials 1. The filter must be in correct position at all times to avoid leaks and possible damage to vac. i CAUTION: To avoid damage to the vac do not run motor with float in raised position. ! 2. When using your vac to pick up very fine dust, it will be necessary for you to empty the drum and clean the filter at more frequent intervals to maintain peak vac performance.
Filter Maintenance Dry Filter WARNING: To avoid injury from accidental starting, unplug power cord before changing or cleaning filter. 1.Some removal of dry debris can be accomplished without removing the filter from the vac by slapping your hand on top of the lid while the vac is off. NOTE: This filter is made Of high quality paper designed to stop very small particles of dust. The filter can be used for wet or dry pick up. Handle the filter carefully when removing to clean or installing it.
Wet/Dry Vac Maintenance Cleaning Lid Assembly CUeaning Drum To keep your Wet/Dry Vac looking its best, clean the outside with a cloth dampened with warm water and mild soap. 1. Dump debris out. IMPORTANT: To assure product SAFETY and RELIABILITY, repairs and adjustment should by performed by Sears Service Centers, always using Sears replacement parts. 3. The drum can be thoroughly washed by scrubbing when filled with warm soapy water. Accessories 2.
Repair Parts ............ FOR 6-GALLON WET/DRY VAC Always order by Part Number - Not by Key Number 113.177120, 113.177440 & 113.177460 WARNING SERVICING OF DOUBLE-INSULATED WET/DRY VAC In a double-insulated Wet]Dry Vac, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added.
Repair PaFts 15 14_ 13 12 10 11
owner's manuaU WET/DRY VAC SERVDCE Service is available by returning this Vac to the nearest Sears Service Center/Department throughout the United States. Modet and serial numbers back of the motor cover. may be found on the MODEL NOS. 113o177120 113.177440 113,177460 (6-Gallon) HOW TO ORDER REPAIR PARTS WHEN ORDERING REPAIR PARTS, ALWAYS FOLLOWING iNFORMATION: PART NUMBER MODEL NUMBER ! 13.177120 (6-Gallon) 113.177440 1! 3.