"x Save This Manual For Future Reference I gJ _A/ S owners monuol MODEL NO. 113.198410 10" DELUXE ELECTRONIC RADIAL SAW WITH 44" CABINET AND 2 DOORS MODEL 113,198610 OR t13.198610 10" DELUXE ELECTRONIC RADIAL SAW WITH 44" CABINET AND 6 DRAWERS Serial Number Model and serial numlc_rs may b_ found at the rear of the bas_. You should record both model and serial number in a safe place for future us_. MODEL 113.
FULL ONE YEAR WARRANTY ON CRAFTSMAN If within one year from the date of purchase, workmanship, Sears will WARRANTY SERVICE CENTER/DEPARTMENT repair this Craftsman RADIAL SAW Radial Saw fails due to a defect in material or it, tree of charge. IS AVAILABLE THROUGHOUT BY SIMPLY CONTACTING THE UNITED STATES. THE NEAREST SEARS SERVICE This warranty applies only while this produc! is used in the United States.
additional instructions for radial arm saws .e..d 3= BEFORE USING €_ e-- THE SAW: WARNING: TO AVOID MISTAKES THAT COULD RESULT IN SERIOUS, PERMANENT INJURY, DO NOT CONNECT POWER CORD UNTIL THE FOLLOWING STEPS HAVE BEEN SATISFACTORILY COMPLETED: 1. Assembly and alignment. (See pages 12-31) 2. Examination and operating familiarity with ONOFF switch, elevation hand wheel, swivel lock, bevel lock and rip lock, guard clamp screw, spreader and anti-kickback device and miter lock. (See pages 37, 38 & 39.
while the cutting tool is rotating. The rotating tool could cut and throw anything hitting the blade causing the saw to unexpectedly come forward. -- -- of a second injury. severe, permanent Do not cycle the motor switch "ON" and "OFF" rapidly, as this might cause the sawblade to loosen. In the event this should ever occur, turn the switch off, allow the sawblade to come to a complete stop, and remove the switch key.
fromthenoseside(oppositethesawdustexhaust chute) of the guard. Note the warningon the guard. --To avoid kickbacks never feed a workpiece through the saw with another piece (butting second piece against trailing end of piece cut) even if of the same thickness, -- To keep control of your workpiece, shorter than the blade diameter. -- -- Toavoidinjuryfromthrownpieces,slips,orjams, theworkpiecemustbehelddownonthetableand againstthefence.Planyour handplacementsto safelyfeed the workpieceinto the cutting tool.
provide additional guarding front of the blade. from contact with the --To prevent the cutting tool from grabbing the table or workpiece and being propelled toward you, never lower a revolving cutting tool into the table or a workpiece without first locking the rip lock handle and clamping the workpiece in place. Release the handle only after having firmly grasped the carriage handle.
Outrip Positioningthe bladeparallelto the fencewith the motor towardthe rearof the sawproducingmaximumrippingcapacity.Seeillustrationon page42. PushStick A deviceusedto feedtheworkpiecethroughthesaw duringnarrowrippingtypeoperationsso the operator'shandsarekeptwellawayfromthe blade.See page43. Push Block A device used for ripping type operations too narrow to allow use of a push stick. See page 43. Rabbet A notch in the edge that has hardened. Ripping A cutting piece.
It is recommended that you have a qualified electrician replace the two prong outlet with a properly grounded three prong outlet. b. Using a small screwdriver, switch to 240V position. cover panel. DUAL An adapter as shown below is available for connecting plug to 2-prong receptacles. The green grounding lead extending from the adapter must be connected to a permanent ground such as to a properly grounded outlet box. slide dual voltage Then replace motor VOLTAGE SWITCH L GROUNDING LUG ADAPTER / "\
1. If the protector opens the line and stops the saw motor, immediately turn the saw switch "OFF", remove the key and allow motor time to cool. tages not more than 10% above or below the nameplate voltage. Heavy loads, however, require that voltage at motor terminals equals the voltage specified on nameplate. 2. After cooling to a safe operating temperature, the overload protector can be closed manually by pushing the red button on the top of the motor.
contents Guarantee Page 2 .................................... General Safety Instructions for Power Tools .... 2 Additional Safety Instructions for Radial Saws .. 3 Glossary Electrical of Terms for Woodworking Connections ........................ ........... Assembly and Alignment ..................... Unpacking and Preassembly ................ Alignment Procedure ....................... 6 7 10 11 26 Page Location and Function of Controls ............ 40 46 50 Maintenance .................
unpacking and preassembly WARNING: TO AVOID INJURY FROM UNEXPECTED STARTING OR ELECTRICAL SHOCK, DO NOT PLUG THE POWER CORD INTO A SOURCE OF POWER. THIS CORD MUST REMAIN UNPLUGGED WHENEVER YOU ARE WORKING ON THE SAW. WARNING: TO AVOID INJURY FROM UNEXPECTED STARTING OR ELECTRICAL SHOCK, DO NOT PLUG THE POWER CORD INTO A SOURCE OF POWER. THIS CORD MUST REMAIN UNPLUGGED WHENEVER YOU ARE WORKING ON THE SAW. Model 113.198410 Radial Saw is shipped in one box. Model 113.198610 Radial Saw is shipped in one box.
44" CABINET ASSEMBLY FOR MODEL NO. 113.198610 WARNING: IF ANY PARTS ARE MISSING, DO NOT ATTEMPT TO ASSEMBLE RADIAL ARM SAW, PLUG IN THE POWER CORD, OR TURN THE SWITCH ON UNTIL THE MISSING PARTS ARE OBTAINED AND ARE INSTALLED CORRECTLY, ASSEMBLE CABINET BEFORE MOUNTING SAW 1. Separate all "loose" parts from packing materials and check each item with "Parts List" to make sure all items are accounted for before discarding any packing material.
CASTER/FOOT ASSEMBLY NO. 50753____8 A R.H. Foot Assembly ......................... B L.H. Foot Assembly ......................... C Caster ..................................... Loose D E F F G H I Parts Bag No. 50752___2 contains 1 1 4 the following: Slotted Truss Head Bolt 1/4-20 x 7/16 ....... Truss Head Bolt 1/4-20 x 1 .................. Hex Nut 1/4-20 ............................ Hex Nut 1/2-13 ............................. Lockwasher 1/4 ............................ Spacer ......................
8. Locate the right and left foot assemblies, two (2) leveling feet, two (2) 1/2-13 hex nuts, the right and left side panels, and four (4) 1/4-20 x 7/16 slotted truss head bolts. Attach theR.H, foot assembly to the right side panel in holes as illustrated. Repeat procedure with L.H. foot assembly to left side panel. J SIDE PANEL SLOTTED SCREW 1/4-20x 7/16 Thread the 1/2-13 hex nuts onto the leveling feet studs. Insert the threaded studs of the leveling feet into the tubes in the foot assemblies.
11.Securerearof lowershelf to right sideandleft sidepanelsusingtwo (2)1/4-20x 1/2trusshead bolts, Iockwashersand hexnuts. Handtighten nutsonlyatthis time. l'_ SIDE J 12. Lay the stand on the backside, locate two (2) spacers, two (2) 1/4-20 x 1"truss head bolts, Iockwashers and hex nuts. Assemble the spacers between each of the foot assemblies and the lower shelf on each side with one (1) truss head bolt, Iockwasher and hex nut each as illustrated. Hand tighten nut. PANEL SHELF 1/4-20 x 1 SPACER 13.
CHECKING CABINET FOR SQUARENESS ii TOOLS NEEDED: Framing square, 3/4" wrench and 7/16" wrench or socket. 1. With cabinet on back side place a square on lower shelf next to right side panel. Adjust stand so both right side panel and lower shelf touch square (as illustrated). Then tighten nut holding rear of shelf to side panel and right side spacer to front of lower shelf. Repeat procedure for left side. 2.
INSTALLING FOR MODEL Tools needed: screwdriver. 1. Locate support, 7/16" DRAWERS NO. 113.198610 wrench or socket, one (1) front support, one and three (3) rear supports. medium (1) upper 2. Slide the upper support into the top of the front support so the top and side holes line up. Then assemble to the front and rear skirts with four (4) 1/4-20 x 1/2 truss head bolts, Iockwashers, and hex nuts. Position bolts from bottom side with threads upwards on front skirt as illustrated.
6. Locate the twelve (12) stand slide brackets, twenty-four (24) truss head bolts, Iockwashers and hex nuts. Assemble the stand slide brackets on the rear supports and inside of the side panels in holes as illustrated. Assemble the stand slide brackets on the center and rear supports in holes as illustrated starting at the top. o_ The rear mounting hole in the stand slide bracket is slightly enlarged and must be mounted to the rear support for stand slide stops to work. Tighten nuts securely. TO 7.
44" CABINET ASSEMBLY FOR MODEL NO. 113.198410 ASSEMBLE CABINET MOUNTING BEFORE Separate all "loose" parts from and check each item with "Parts all items are accounted pack_ng material. 44" CABINET FOR MODEL A B C D E F G H I J K L AH packing materials List" to make sure for before ASSEMBLY WARNING: IF ANY PARTS ARE MISSING, DO NOT ATTEMPT TO ASSEMBLE RADIAL ARM SAW, PLUG IN THE POWER CORD, OR TURN THE SWITCH ON UNTIL THE MISSING PARTS ARE OBTAINED ARE ARE INSTALLED CORRECTLY.
2.Afterlayoutofstandparts,takethe bottomshelf andturn upsidedownonfloor.Smallfrontflange shouldbe pointingupward. 3. Place one shelf stiffener shelf as shown. r against front flange of 4. Place the under support on the shelf. Locate two (2) 1/4-20 x 1/2 truss head bolts, Iockwashers and hex nuts from loose parts bag #488. Attach the supports to the shelf in holes as illustrated and tighten nuts with 7/16" wrench or socket. 5.
8. Locate the right and left side panels and eight (8) 1/4-20 x 1/2 truss head bolts, Iockwashers and hex nuts to attach side panels to shelf. Mount the bolts through the four holes as illustrated and tighten with 7/16 wrench or socket. To assemble, lay the side panel on its backside and stand the shelf up as illustrated. ,t_ BOTTOM SIDE OF LOWER SHELF Em_ RIGHT SIDE PANEL 9.
CHECKING CABINET TOOLS NEEDED: and 7/16" wrench FOR SQUARENESS Framing or socket. square, 3/4" wrench 1. With cabinet on back side place a square on lower shelf next to right side panel. Adjust stand so both right side panel and lower shelf touch square (as illustrated). Then tighten nut holding rear of shelf to side panel and right side spacer to front of lower shelf. Repeat procedure for left side. 2.
MOUNTING DOORS FOR MODEL NO. 113.198410 1. Slide the upper support into the top of the center support so the top and side holes line up. Then assemble to the front and rear skirts with four (4) 1/4-20 x 1/2 truss head bolts, Iockwashers, and hex nuts. Position bolts from bottom side with threads upwards on front skirt as illustrated. Tighten hex nuts securely. 2. Assemble the front support to the lower and the upper supports with four (4) 1/4-20 x 1/2 truss head bolts, Iockwashers, and hex nuts.
MOUNTING 1. From loose hardware: SAW parts bag #488, find the following 8 - Truss Head Bolts 1/4-20 x 1/2 8 - Lockwashers External 1/4 8- Hex Nuts 1/4-20 T.uss.EAOBO,TIf 2. Place saw on cabinet so that holes in bottom saw line up with holes in top of cabinet. 3. Install bolts, Iockwashers, and nuts Tighten securely using a 7/16" wrench of as shown. or socket.
Attach Elevation Handwheel 1. From loose parts bag, find one (1) screw 10-32 x 1/2 and one (1) external Iockwasher. Install handwheel to front of base as illustrated. ELEVATION HANDWHEEL MOUNTING 1. Remove wrenches MOTOR the blade guard. Locate and remove the blade. CAUTION: 13o not attempt the blade guard and blade the to mount the motor have been removed. 2. Elevatethe arm approximately shipping pad. 3.
ALIGNMENT PROCEDURE IMPORTANT: In order to obtain maximum cutting accuracy and safety, the following six steps must be carefully followed. Become thoroughly familiar with these steps so that you can always maintain your saw in proper alignment. The accuracy of each adjustment is always dependent upon the accuracy of the preceeding adjustment. Be sure to align the saw in the exact sequence described to insure proper alignment and cutting accuracy.
6. Lay the arbor wrench on the work tableunderthe motor shaft. Carefully lower the arm with the elevation handle until the motor shaft is just touching the arbor wrench. The wrench should slide back and forth with only slight contact with motor shaft. NOTE: When moving the arm from the left side to the right it is necessary to move the motor along the arm to check the front table at several points from front to back. 7.
Adjusting front table lock handles WARNING: TO BREAKAGE, OR TABLE BOARD TABLE BOARDS PLACE. AVOID SUDDEN SLIPPAGE, THROWING OF PARTS, FRONT LOCK HANDLE MUST LOCK AND RIP FENCE SECURELY IN 1. To adjust the table board clamps check by pulling up on rip fence. There should be enough pressure to keep the rip fence from pulling up. To adjust the pressure on the clamp: a. Lift front table lock pressure on boards. handles b. Loosen the two eccentric located at the rear of the 7/16" wrench or socket.
(c) Carefully retighten uppertwo (2) 1/4-20 socket set screws alternating from left side to right side so as not to force arm out of adjustment. FOUR HEAD (d) Recheck blade travel. Adjust arm position as needed by readjusting upper screws only. SOCKET SCREWS (e) Once arm position is good, tighten lower 1/420 socket set screws. Do not overtighten. Check elevating handwheel for ease of rotation. If rotating handwheel is difficult, readjust socket set screw tightness as needed.
STEP Squaring Blade FIVE to Rip Fence NOTE: If alignment procedure steps three and four were not performed, this adjustment step cannot be accomplished. This adjustment helps avoid binding (kickbacks) or splintering of wood surface, or burning of the kerf. 1. Position carriage as shown and tighten rip lock handle. Place a framing square against the rip fence and the saw blade, as shown.
a. b, Unlock the bevel lock handle and loosen the two cap screws located thru the rear of the motor support (see illustration). A 1/8" hex "L" wrench is needed to loosen these screws. Lift or lower the rear of the motor support the gap between the blade and square appears. Lock the bevel lock handles. until dis- _YOKE c. Tighten the two cap screws and recheck alignment between the face of the blade and the square. If a gap condition exists, repeat the above adjustment. MOTOR SUPPORT _AP SCREWS d.
location and function of the electronic indicator system BATTERY STORAGE COMPARTMENT (ON SIDE) FUNCTION ON/OFF ELECTRONIC MEASUREMENT Digital Readout LOCK REMOVE YELLOW KEY BEVEL ANGLE FUNCTION KEY MITER FUNCTION KEY RIP POSITION FUNCTION BLADE ELEVATION FUNCTION KEY REFERENCE SET KEY KEY ANGLE DIGITAL TO INDICATORS READOUT DISPLAY KEY Display The liquid crystal display (LCD) on this saw gives the user the ability to accurately position the saw blade and make precision adjustments to
1. Installing the Battery Install the battery into the compartment as shown. The bottom rear tab of the battery should be held inside the compartment by the bottom wall of the casing. BATTERY The indicator display should appear within a second or two after the battery is correctly installed. If the display remains blank, remove and reinstall the battery. If the display still remains blank, refer to the trouble shooting guide in this manual. Once the display is activated, install compartment cover.
Loosen the miter angle encoder mounting bracket by backing the mounting screws off until the encoder will rotate slightly on the column tube. d. e. Rotate the encoder on the tube by tapping the encoder lightly until the display reads "45.0". Do not force or hit the encoder to make this adjustment. LINE UP WITH HOLE f. Re-tighten the encoder mounting screws and re-check the encoder display using steps 1 through 6 above. g.
Pressthe key. Presstose, thezero f. If the adjustment will not align the display readout to the bevel index positions, refer to the trouble shooting guide in this manual reference readout. This g. When the encoder alignment has been completed, the electronic indicator system should be ready for use. Using the Electronic Indicator System 1. Setting the indicator reference points. the display "On" tho by pressing bevel displav readout. should This read: reference Press the [_'TER]I key.
location and function WARNING: FOR YOUR OWN SAFETY ALWAYS LOCK THE SWITCH "OFF" WHEN SAW IS NOT IN USE. REMOVE KEY AND KEEP IT IN A SAFE PLACE . . . ALSO IN THE EVENT OF A POWER FAILURE, TURN SWITCH OFF. LOCK IT AND REMOVE THE KEY. THIS WILL PREVENT THE SAW FROM STARTING UP AGAIN WHEN THE POWER COMES BACK ON.
Depth of Cut (Elevation) a. The diagram shows the elevation crank which is used to raise and lower the saw blade. b. Clockwise rotation raises the blade . . . counterclockwise rotation lowers it. One complete turn of the handle will raise or lower the saw blade 1/16 inch. c. Handle can be folded in when not in use. 2.
5. Blade Angle (Bevel) a. A single bevel lock handle is used in angular positioning and indexing of the motor, to provide the desired saw blade (bevel) angle. 5 b. The bevel lock handle controls the angular position of the motor with respect to horizontal. C. d° The bevel lock handle automatically indexes the motor at 0 °, 45 ° and 90 ° . Slide the bevel lock handle to the far right while positioning the blade, then release it. At any other position it does not engage.
8. Blade Guard and Anti-Kickback/Spreader Assembly- Positioningfor Ripping. WARNING:NEVERPOSITIONTHE GUARDOR ANTI-KICKBACK/SPREADER ASSEMBLYWITH THESAWRUNNING. NEVERPOSITIONTHEANTIKICKBACK/SPREADER ASSEMBLY BYGRASPING 8 GUARD CLAMP SCREW THE PAWLS OR SPREADER. TO MAINTAIN SPREADER ALIGNMENT, USE THE TAB LOCATED ON THE ANTI-KICKBACK BAR. WORK a. The blade guard is positioned by loosening the guard clamp screw and rotating the guard so that the "nose" just clears the workpiece as shown.
basic saw operation WARNING: TO AVOID MISTAKES THAT COULD CAUSE SERIOUS PERMANENT INJURY, OBSERVE ALL THE FOLLOWING INSTRUCTIONS IN ADDITION TO THOSE ON PAGES 2-6. Basic saw operations are summarized in six categories, explained and illustrated in the following paragraphs. NOTE: Refer to paragraphs under "Location and Function of Controls" for illustrations and description of controls. Page 36.
2. Make sure the arbor nut is snug. 3. Clamp the guard in a horizontal 4. Lock the swivel lock handle. locked. (See page 37.) position. Make sure it is firmly 5. Hold work firmly against table and fence. To avoid tipping or throwing of workpieces thicker than the fence is high, install a higher fence (at least workpiece thickness). Always place the fence in the most forward position (farthest from the column support) compatible with the workpiece being processed and the operation being performed.
rectangular frame. The radial arm is set to a desired angle of cut, swivel and bevel settings at 0 ° and locked. The workpiece being cut is positioned and held firmly against the fence and the carriage pulled forward along the radial arm just far enough to complete the cut. Carriage should then be returned to the full rear position and locked. Allow the saw blade to come to a stop before removing the workpiece from the saw table. OPERATION NO.
board against the fence must be straight and will not catch on kerfs in the fencefor workpieces thicker than the fence is high, install a higher fence (at least the thickness of the workpiece). N EVER RIP "FR EEHAN D" (without aid of fence). 5. Properly set the anti-kickback and spreader assembly. Observe INSTRUCTIONS in paragraph "Positioning guard and anti-kickback and spreader assembly for ripping" under "Location and Function of Controls" page 39. 6. Never rip pieces blade.
OPERATION NO. 5 OUT-RIPPING AND IN-RIPPING 1. Ripping is the process of sawing the workpiece along its length by feeding it into the sawblade when using the fence as a guide and as a positioning device to obtain the desired width of cut. The sawblade is parallel to fence. 2. Since the work is pushed along the fence, it must have a straight edge in order to make sliding contact with the fence. Also, the work must make solid contact with the table, so that it will not wobble or kickback.
OPERATION NO. 6- BEVEL RIPPING Bevel ripping is either in-ripping or out-ripping as described above, except the saw blade is tilted out of perpendicular to the saw table surface. The radial arm is indexed at 0 ° and locked, the bevel is set to the desired bevel angle and the yoke is positioned for ,n-ripping (saw blade at rear) or outripping (saw blade at front), as required. All requirements and observations applicable to normal ripping operations also apply to bevel ripping.
AUXILIARYFENCEFORMOLDING To use crosscut the molding head with the arm position an auxiliary fence must in the 0 ° be used. AUXILIARY FENCE SPACER TABLE // WARNING: IF THE AUXILIARY FENCE IS NOT USED WHEN THE SAWARM ISIN THE0 ° CROSSCUT POSITION, THE MOLDING HEAD CANNOT BE LOCATED BEHIND THE FENCE FOR SAFE AND PROPER OPERATION. Make the auxiliary fence pine. Cut to the following --18-3/4" --1 from a piece dimensions.
5. Adjustment is complete when both locking and indexing functions are working properly. Replace motor support cover. ADJUSTING SWIVEL LOCK HANDLE This handle provides a friction lock between the upper face of the yoke and the bottom face of the carriage. It should eliminate any play or rotation between these two parts when locked.
ADJUSTINGCARRIAGEBEARINGS The carriage should roll freely but with some resistance for the entire length of travel. To test for bearing looseness, perform the following steps. 1. Place yoke in either 2. Push the carriage the in-rip back or out-rip against position. the rear stop. 3. Hold the front carriage bearing with your fingers as tight as possible and pull carriage forward at the same time. If you can prevent the bearing from turning an adjustment is required.
j-- ( 2. With a 3/16 inch hex "L" wrench find the 1/4-20 hex socket cap screw through the hole in the rear arm cover. To tighten turn the wrench clockwise approximately 1/4 turn. 3. Lock the miter lock handle and try again the arm. Readjust if necessary. to move ° @ ° 4. If it becomes extremely difficult to push the miter lock handle into the locked position too much adjustment has been made. Turn the wrench counterclockwise one half the amount of the last adjustment and try again to lock the arm.
trouble-shooting HAVE YOU FOLLOWED ALL SIX STEPS OF THE ALIGNMENT PROCEDURE? IF YOU HAVE NOT FOLLOWED THEM IN THEIR PROPER SEQUENCE, YOU CANNOT EXPECT A CCURA TE CUTTING RESUL TS. In addition to the proper alignment of your saw, you must also become familiar with the following practices in order to expect the best results. 1. Edge of workpiece which is placed must be as straight as the long framing square. against fence side of your THIS EDGE OF BOARD AGAINST FENCE FOR ALL CUTS /J / " 1 I 2.
1. RADIAL SAW DOES NOT MAKE ACCURATE or 45 ° MITER CROSSCUTS. 0° a. Looseness between column tube and column support. Align as described Section Step One. in Alignment FINISH CUT END FINISH _ SQUARE / , CUT END SQUARE / Procedure // , '_\'\\ b. Crosscut travel not properly adjusted. j; Refer to Step Three in Alignment Procedure Section Squaring Crosscut Travel. ' ,t/ \_ I '\\ I c. Column is Loose in Support. Refer to Step One in Alignment '/i Procedure. t d.
4. SAW KERF (CUT EDGE) OF STOCK ROUGH -TOOTH MARKS LEFT ON EDGE OF SAW KERF. NOTE: This condition a, Crosscutting is commonly : - called "HEEL". ROUGH KERF : FENCE J__- WIDE CU'[ or Miter Culling. "Heeling" will tend to slide the workpiece along the guide fence, as the cut is being made, and make a square cut almost impossible. Refer to step 5 under Alignment Procedure Section -"Squaring Blade to Fence." b. Bevel Crosscutting Or Bevel Ripping.
9. CLAMPING FORCE NOT SUFFICIENT MITER ANGLES OTHER THAN 45 °. a, Miter Lock Handle requires AT Adjustment. Refer to Adjusting Miter Lock Handle in Adjustments to Compensate for Wear Section. 10. CLAMPING FORCE NOT SUFFICIENT BEVEL ANGLES OTHER THAN 45 ° . AT a. Bevel Lock Handle Requires adjusting. Refer to Adjusting Bevel Lock Handle in Adjustments to Compensate for Wear Section. 11. DEPTH OF CUT VARIES FROM ONE END OF WORK PIECE TO THE OTHER. a. Table Top not parallel with Arm.
TROUBLE PROB'EM ] SHOOTING PROBABLE GUIDE - ELECTRONICS SUGGESTED CAUSE CORRECTIVE ACTION i No display when is pressed. 1. Battery incorrectly installed. '2. Battery contacts or corroded. - Adjust dirty - Clean 3. Battery dead. 4. Indicator Display '1. Normal ; battery unit. shows or , display failure. display when is first installed display in compartment. contacts. - Have electronics checked technician. Repair service Sears Store.
MOTOR TROUBLE-SHOOTING CHART NOTE: Motors used on wood-working tools are particularly susceptible to the accumulation of sawdust and wood chips and should be blown out or "vacuumed" frequently to prevent interference with normal motor ventilation. TROUBLE PROBABLE Motor will not run. !. Protector broken. CAUSE SUGGESTED open; circuit REMEDY 1. Reset protector by pushing on red button, located on top of motor (indicated by audible check). 2. Check power line for proper voltage. 2. Low voltage.
maintenance and lubrication MAINTENANCE WARNING: FOR YOUR OWN SAFETY, TURN POWER SWITCH "OFF'AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MAINTAINING OR LUBRICATING YOUR SAW. When you receive your new Craftsman radial saw, it requires no lubrication. The radial saw has been partially aligned and all bearings are lubricated and sealed for life. In time, however, in order to keep your saw in perfect working order and accurate, it will be necessary to lubricate and realign.
A light film of oil should be wiped on the column tube to lubricate the fit between tube and column support. With elevation arm to upper limit. Completely collapse pulling down on top flange as illustrated to column tube. face of the the column crank raise bellows by for access The thread on the elevation shaft assembly can be lubricated through the oil hole in the center of the radial arm cap. Lubricate ramp on the swivel index spring.
repair parts PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113,198410 and 113.198610 SAW 10 (SEE FIG, 6) 15 16 _ ©_ ..... 26 / 1 22 28 25 I 27 36 (SEE FIG. iJ \\ 33 49 30 2) (SEE (SEE FIGS. 3 & 4) FIG, 10) \ 31 FIG. 8) 52 / 2O 8 (SEE FIG. 2) 4a.
PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198410 and 113.198610 SAW Always order by Part Number - Not by Key Number FIGURE Key No. 1 2 3 Part No. ST D601103 815773 815857-1 808380-6 5 6 7 8 815710 815649 815820 813785 9 10 1! 806828-2 12 13 60128 815797 14 141594-31 15 16 17 18 19 20 21 22 23 24 25 26 27 37384 815762 815989 STD532512 815834 STD551225 STD541025 815990 STD522506 STD551012 STD541425 815832 815797 28 29 446188 815939 815986 30 *Standard Hardware Key No.
PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198410 and 113.198610 SAW 6 J% 8 1 _ !1 22 4O 12 \\ 14 " 19 34 > 17 18 28 20 16 21 27 28 46 29 3O 24 J 2O / 16 26 25 FIGURE 60 2 23
PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198410 and 113.198610 Always order by Part Number FIGURE Part No. Key No. 1 815857-1 2 3 i815649 1141594-31 4 5 6 7 8 :815774 i815702 i60208 1815763 !816845-1 11 12 13 14 15 16 815672 330751 815754 815770 60531 815690 2 - BASE Hd. Bearing, Arm *Screw, Socket Hd. Cap 1/4-20 x 1-1/4 Rivet, 1/4 x 1/2 Lock Assembly Nut, Push 1/4 Latch Arm Screw, Soc. Hd.
PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198410 and 113.198610 SAW 6 8 9 I // 1o / 11 12 13 14 \ 18 22 20 31 13 J % 29 28 27 33 24 4/ 25 FIGURE 62 3
PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198410 and 113.198610 SAW Always order by Part Number - Not by Key Number FIGURE Key No. Part No. 1 2 815803 810214-2 3 4 5 6 7 815798 STD551012 816263 8 9 10 11 12 13 14 15 16 17 18 19 20 815682 815683 815776 815678 815679-1 805561-10 815791 815677 815813 815836 815685 815799 815686 808380-6 3 - YOKE AND MOTOR Description Cap, Motor Support Screw, Low Hd.
PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198410 and 113.198610 SAW 9 7 \ 17 / 2 3 4 1 18 19 23 38 39 27 / 29 FIGURE 64 4
PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198410 and 113.198610 SAW Always order by Part Number - Not by Key Number FIGURE Key No. Part No, ! 810214-3 2 3 4 5 6 7 8 STD315485 STD551031 815808 815689 STD551062 815827 STD600803 11 12 13 14 815817 STD541462 62636 815693 STD541425 273229 15 16 17 18 19 20 816497 815671 815804 815692 STD532507 808380-2 *Standard Hardware 4 - YOKE Key No. Description Screw, Low Hd. Cap 5/16-18 x 7/8 *Bearing, Ball .3150 I.D.
PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198410 and 113.198610 Always order by Part Number SAW - Not by Key Number 9 10 14 15 16 23 / 22 19 FIGURE Part No. !Key No. 1 2 3 4 5 815688 815809 815774 815790 STD601103 6 7 815703 815856 8 9 10 11 12 13 14 815779 815741 STD363539 815735 815704 STD551208 STD600803 15 16 17 18 19 20 815775 815863 815976 815938 815789 816206 *Standard 66 5 - ARM ASSEMBLY Key No.
PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198410 and 113.198610 SAW Always order by Part Number - Not by Key Number 1 FIGURE Key No. 1 2 3 4 6 - TABLE Part No. 815757 815755 815758 815756 *Standard Hardware ASSEMBLY Description Table, Rear Table Spacer Fence, Rip Table, Front Item may be Purchased Locally.
PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113,198410 and 113.198610 Always order by Part Number - Not by Key Number ] FIGURE 7 - FOOT Key No. Part No. 1 STD601103 2 3 4 5 6 7 8 9 10 11 -- 815874 815877 815879 815871 STD541250 803835 815878 815875 803927-3 808503-1 507522 *Standard 68 ASSEMBLIES Hardware - MODEL 113.198610 Description *Screw, Pan Rec. Hd.
PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198410 and 113.198610 SAW Always order by Part Number - Not by Key Number 7 5 \ 4 1 8 10 9 9 11 12 9 14 FIGURE Key No. Part No. 1 2 3 4 5 6 7 816264-1 120399 63258 63541 815816 STD551010 ST D601103 8 9 STD541231 815815 *Standard Hardware 8 - GUARD Key No. Description Guard *Nut, Square 5/16-18 Elbow, Dust Bar, Anti-Kickback Guide, Anti-Kickback *Washer, 13/64 x 5/8 x 1/32 *Screw, Pan Hd.
PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198410 and 113.198610 gJ / \ / \ ! 70 SAW
PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198410 and 113.198610 SAW Always order by Part Number - Not by Key Number • .m 5 !?! 0 u. _.z I _ <_ o_c _° Q_ _ I _0_ __ 03 03 I- u.I Z 0 0 .._1 X o ('kl O 03 ,,, c O om O. "." =_ ",r-- _ _-- (D (D C __ (D *--, _ C CO -r': --- _ _ __- _ o_ m I.I. O0 O0 O0 Z f- 13._ _._ _ o_ _ O0 O0 O0 __ F_ _ CO0"] m -r0___ O0 c ...,.
PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198410 and 113.198610 SAW 10 5 4 \ / / i I / L //' / 19 4 3 / 21 19 / ;4_ 19 19 18 FIGURE 72 10
PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198410 and 113,198610 SAW Always order by Part Number - Not by Key Number FIGURE Key No. Part No. 1 2 3 4 5 6 7 8 9 805589-5 815898 STD541025 STD551225 815893 815891 815886 815933 816274 10 11 12 13 815906 STD541250 816111 815941 *Standard Hardware 10 - CABINET ASSEMBLY Description Screw, Truss Hd.
PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198410 and 113.198610 Always order by Part Number SAW - Not by Key Number 3 \ \ FIGURE 11 - DRAWER Key No. Part No. 1 1815912 2 3 815917 815919 330751 815923 815901 815902 *Standard 74 Hardware ASSEMBLIES 3", 6", 10" Description Drawer Assembly, 3" Drawer Assembly, 6" Drawer Assembly, 10" Fastener Drawer Front, 3" Drawer Front, 6" Drawer Front, 10" Item may be Purchased Locally.
NOTES 75
r -_ F owners manual SERVICE MODEL NO. 113.198410 10" DELUXE ELECTRONIC RADIAL SAW WITH 44" CABINET AND 2 DOORS OR 113.198610 10" DELUXE ELECTRONIC RADIAL SAW WITH 44" CABINET AND 6 DRAWERS HOW TO ORDER REPAIRPARTS l O-INCH DELUXEELECTRONIC RADIAL SAW Now that you have purchased your flO-inch electronic radial saw, should a need ever exist for repair parts or service, simply contact any Scars Scrvice Center and most Scars, Roebuck and Co. stores.
