//_ Save This Manual For Future Reference "_ MODEL NO. '_!3.2'13!30 DRILL PRESS WITH MAXIMUM DD!ELOPED 2/3 HP MOTOR Serial Number Model and serial number may be found at the rear of the head. You should record both model and serial number in a safe place for future use, l lll MOTORIZED I EL CAUTION: READ ALL iNSTRUCTIONS CAREFULLY ,L Pl e assembly e operating • repair parts x,.. Sold by SEARS, ROEBUCK AND CO., Chicago, Part No. SP5186 tL 60684 U.S.A.
FULL ONE YEAR WARRANTY ON CRAFTSMAN DRILL PRESS If within one year from the date of purchase, this Craftsman Drill Press fails due to a defect in material or workmanship, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERViCE CENTER!DEPARTMENT THROUGHOUT THE UNITED STATES. This warranty applies only while this product This warranty gives you specific vary from state to state. legal rights, is used in the United States.
additional safety instructions WARNING: FOR YOUR OWN SAFETY, DO NOT USE YOUR DRILL PRESS UNTIL mT IS COMPLETELY ASSEMBLED AND INSTALLED ACCORDING TO THE INSTRUCTIONS... AND UNTIL YOU HAVE READ AND UNDERSTAND THE FOLLOWiNG: 1. General Safety Instructions for Power Tools. 17 3. Basic Drill Press Operation 22 4. Adjustments .......................... 5. Maintenance .......................... -- 2 2. Getting to Know Your Drill Press ........ ............. for drill presses -- 24 25 6.
_:_ Dum ths dd RPM pi'e_ NEVER be operated on at a _ed g_eater than t800 c Do _ot inStait o_ ,,,_seany driP!that exceeds 7" in engt_ 0 e×te_tds 6!t'below the Chuck aws.
gaossary of terms 1. Workpiece The item or_ which performed. the cutti_'_g operations is being 2. Drill The cutting tool used in the drii_ press to make hotes in a workpiece. 4. Revolution Per Minute (R.P.M.) ]he number of turns ,,:ompleled by a sp_nn_ng object in one minute 5. Spindle Speed The RPM of the spindie. 3. Backup Material A piece of wood placed between the workpiece and table ....
motor specifications electrical requirements i, MOTOR SPECiFICATiONS ThiS drili press is designed to use a 1725 RPM motor only. Do not use any motor that runs faster than t725 RPM, It is wired for operation on 1 t 0-120 volts, 60 Hz. alternating current. WARNING: TO AVOID INJURY FROM UNEXPECTED STARTUP, DO NOT USE BLOWER OR WASHING MACHINE MOTORS OR ANY MOTOR WiTH AN AUTOMATIC RESET OVERLOAD PROTECTOR.
unpacking and checking WARNING: TO AVOID iNJURY FROM UNEXPECTED STARTING OR ELECTRICAL SHOCK, DO NOT PLUG THE POWER CORD INTO A SOURCE OF POWER. THIS CORD MUST REMAIN UNPLUGGED WHENEVER YOU ARE WORKING ON THE DRILL PRESS. Mode! 113.213130 one box. 1. Unpacking Drift Press and Checking is shipped complete in Contents a. Separate all "loose parts" from packaging materials and check each item with "Table of Loose Parts" to make sure all items are accounted for.
B List of Loose Parts in Box 507872 ,tern Description Rod ...................... B Knob .................. C Crank .............................. D Screw Soc. Set M6 x 1.0-10 ............ C /_'_/' Qty. _LU_ 3 3 \ "_ _/ \ I1_' J --:f _ I11 _ 1 1 /_ / E Clamp-Column,,. ...................... 1 F Wrench-Hex"L 3mm ................. 1 G Wrench-Hex "L" 4mm ................. 1 -- Bag of Loose Parts (Not Shown) ...... 1 * Items on this page marked with this symbol are illus- _]_ A trated full size.
mecation and functien 1. BELTTENSION HANDLE..• Turn handle counter clockwise to apply tension to belt. turn handle clockwise to release belt tension, 2. BELT TENSION LOCK HANDLE... Tightening handles locks motor bracket support and BELT TENSION HANDLE to maintain correct bett distance and tension ef centrols 9. CHUCK.., accessory Holds drill bit or other recommended to perform desired operations. 10. BEVEL SCALE, . . Shows degree table is tilted for bevel operations.
assembgy WARNING : FOR YOUR OWN SAFETY, NEVER CON" NECT PLUG TO POWER SOURCE OUTLET UNTIL ALL ASSEMBLY STEPS ARE COMPLETED. FRAMING SQUARE MUST BE TRUE. Check its accuracy TOOLS NEEDED as Illustrated DRAW LIGHT LiNE ON BOARD belowo STRAIGHT EDGE OF BOARD 3/4" THICK-- 15/16" BOX END WRENCH COMBINATION SQUARE MEDIUM SCREWDRIVER ASSEMBLY HARDWARE I[(_(..
iNSTALLiNG THE TABLE SUPPORT LOCK TABLE 1. Loosen support lock and raise table support by turning table crank clockwise until support is at a working height level. Tighten support lock. TABLE SUPPORT f RACK m 2. Remove protective covering from table and discard. Place table in table support and tighten table lock (located under table) by hand. TABLE_ LOCK INSTALLmNG TABLE THE HEAD CAUTION: The head assembly weighs about 55 pounds. Carefully lift head. 1.
MOUNTING MOTOR MOTOR BRACKET 1. Locate four (4) 8turn Dig × 20mrn long hex head bolts, eight (8) flat washers, and four (4) nex nuts among loose parts. 2. Install head, hex head bolls through motor bracket 3. Place motor in position so motor base slots hne up with motor bracket slots. Install flat washers ane inex nuts as illustrated (Do not tighten1 4.
V-BELT \ SPINDLE PULLEY 5. Locate V-belt in the loose parts bag. 6. Use speed chart inside belt guard to choose speed for drilling operation. Install belt _n correct pos_t_on for desired speed NOTE: Refer to chart inside mended Drilling Speeds. belt guard for Recc)m- 7. Apply tension to belt by turning Belt Tension Han:l e counter clockwise until belt deflects app_oximateiy !/2 inch by thumb pressure at _ts center 8.
MOTOR CONNECTIONS WARNING: FOR YOUR OWN SAFETY- NEVER CONNECT PLUG TO POWER SOURCE OUTLET UNTIL ALL ASSEt_BLY STEPS ARE COMPL ETED, WARNING; CONNECT (COLORED 2 BLACK WIRE TO L #1 COPPER POST GREEN WIRE TO GREEN SCREW TO &VOID ELECTROCUTION, NEVER ANYTHING BUT THE GROUND WIRE GREEN} TO THE GREEN SCREW. STRAIN RELIEF GROOVE WHITE WIRE ,4, m_w_ GRE[fN :s,:REW a_r_ _nser; mrougr_ rounf_ ,;era 0.-._m;;__ r-.
_SPINDLE SUPPORT LOCK 3. Unlock support lock and raise table two (2) inches below tip of chuck. \ so its about 4. Turn chuck sleeve clockwise and open jaws _n chuck comp_etefy 5. Turn feed handles counterclockwise ai]d force chuck against table untii chuck is secure.
ADJUSTING TO HEAD THE TABLE SQUARE NOTE: The comb _t_on sauare must be "true." See 'Unpacking and Checking Contents" section for method, 1 Insert a preciston ground steel roe approximately 3" long into chuck and tighten, 2. With table raised to working height and locked on column, place combination square flat on table beside rod TABLE / 3. If an adjustment is necessary, loosen the set screw under bevel lock with 3ram Hex L" wrench, then loosen the table bevel lock with a 15/16" wrench.
getting to know your driUmpress FEED SPRING ADJUSTMENT FEED SPRING BELT 17 SPRING CAP 1 GUARD / DRILL "ON-OFF" SWITCH 2 BELT TENSION LOCK HANDLE 19 ARM 2 BELT TENSION LOCK HANDLE 21 TABLE LOCK 23 3 BELT TENSION HANDLE 16 DEPTH SCALE LOCK LOCK 22 BEVEL SCALE 20 TABLE BEVEL LOCK (UNDER ARM) QUILL AND INSIDE SPINDLE OF DRILL 4 HEAD LOCK SET SCREWS 15 INDICATOR 5 FEED HANDLE 14 DEPTH SCALE 6 COLUMN 7 5 SUPPORT ASSEMBLY PRESS SPINDLE SPLINES ( COLLAR 8 TABLE CRANK 13 TABLE RACK ) 1
This Dr_ll Presshas 5 soeeds 500 990 1500 2250 3t00 as listed below: R3M _>M qPM RPM RPM See inside of belt guard for specific on pulleys, placement of belts SPINDLE SPEE#S iN R.P.Mo 1500 500 3100 2250 [ 1. BELT GUARD and beit dunng ASSEMBLY . . . Covers operation of dri! 3ross pulleys 2. BELT TENSION LOCK HANDLES... T ghtenmg bandies locks motor bracket support and BELT TENSION HANDLE [o ma_ntaln correct belt d_slance and tension. 4. HEAD LOCK SET SCREWS . ..
27 DRILL "ON-OFF" SWITCH . . , Has locking feature. THIS FEATURE IS INTENDED TO HELP PREVENT UNAUTHORIZED AND POSSIBLE HAZARDOUS USE BY CHILDREN AND OTHERS. Insert KEY into switch. NOTE: Key is made of yellow plastic. To tum drill ON , . Insert finger under switch lever and puli. % To turn drill OFF... Push lever in In an emergency: .., the drill bit BINDS. , . STALLS . , . STOPS . . . or tends to tear the workpiece loose •.
i,'_i_ii_i_i_i_?, _ DRILLING , TO A SPECIFIC i_ i i_ DEPTH" tt To drill a BLIND hole (not all the way through) to a given depth proCeed as follows, t Mark the depth of the hole on the side of the workpiece. 2: Loosen the depth scale !ock. .... !i ii With the Switch OFF, bring the drill down until the TIP or lips of the drill are even with the Mark: 4. Turn the depth scale counterclockwise until it stops moving. DEPTH SCALE 5, Tighten the depth scale lock.
DEPTH SCALE LOCK 3. Turnthe depthscaleclockwiseuntilit stops, 4. Tightenthe depthscalelock. 5. Thechuckwillnowbeheldatthisdepthwhenthe feedhandlesarereleased. REMOVING CHUCK 1. Raise the table so it is about (2) two inches below the chuck, This will prevent the chuck falling a long distance when it is removed. 2. Put a wrench (no longer than 11 inches) the chuck and spindle as illustrated. between 3. While prying down on the wrench hit the side of the chuck using a rubber or plastic hammer.
basic d tl( press operation L; owthef0 owng nstruct ons for operating your dr pres_ to get the best results and to minimize the likeli, -- h oao!persona injury, onthetab elexcept whenpolishing WARNING: FOR YOUR OWN SAFETY, ALWAYS OBSERVE THE SAFETY PRECAUTmONS HERE AND - Securely lock Head and Support to Column, Table Arm to support, and Table to Table Arm before operating drill press. -- Never move the Head or Table while the tool is running.
POSITIONING "TABLE AND WORKPIECE Lock the table to the column in a position so that the tip of the drill is just a little above the top of the workpiece. Always place a piece of BACK-UP MATERIAL (wood, plywood. , .) on the table underneath the workpiece. This will prevent "splintering" or making a heavy burr on the underside of the workpiece as the drill breaks through, TO keep the backup material from spinning out of control, it must contact the left side of the column, as illustrated.
TILTING TABLE i :VEL LOCK : : To use the table in a bevel ttilted) position, loosen the set screw under table bevel lock with Hex "L" wrenchl Loosen bevel Iodk With adjustabie Wrench: iTilt tab e to desired angle by reading bevel scale. tighten bevel lock and set screw. Rei BEVEL (3 SET SCREW WARNING: TO AVOID INJURY FROM SPINNING WORK OR TOOL BREAKAGE, ALWAYS CLAMP WORKPIECE AND BACKUP MATERIAL SECURELY TO TABLE BEFORE OPERATING DRILL PRESS WITH THE TABLE TILTED.
maintenance WARNING FOR YOUR OWN SAFETY, TURN SW_TCH "OFF" AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MAINTAINRNG OR LUBRICATaNG YOUR DRILL PRESS. Frequently blow out any dust that may accumulate inside the motor. A coat of furniture-type paste wax applied to the table and column will help to keep the surfaces clean. WARNING: TO AVORD SHOCK OR F_RE HAZARD, IF THE POWER CORD nS WORN OR CUT, OR DAMAGED IN ANY WAY, HAVE IT REPLACED AMMEDIATELY.
trouble shooting WARNING: FOR YOUR OWN SAFETY TURN SWITCH "OFF" AND ALWAYS REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE TROUBLE SHOOTING. e CONSULT YOUR LOCAL SEARS SERVICE CENTER IF FOR ANY REASON MOTOR WILL NOT RUN. TROUBLE PROBABLE CAUSE REMEDY i Noisy Operation 1. Incorrect belt tension. 1. Adjusttension, Seesection "ASSEMBLY--TENSIONING BELT." 2. Lubricate spindle. See "Lubrication" section. 3. Checking tightness of retaining nut on pu!ley, and tighten if necessary. 4.
repair parts PARTS LmST FOR CRAFTSMAN 13" DRILL PRESS MODEL NO. 113.213130 1 \ 5 6 5 7 8 12 16 15 13 Always order by Part Number--Not FIGURE Key No. Part No. 1 2 3 4 5 6 7 8 9 10 STD303390 817440 817504 8! 7407 STD315235 817408 817453-1 817453 STD315215 817325 by Key Number 1 PARTS LiST Key No. Description * Belt-"V" 3/8 x 39 Nut-Hex 1 "-20 LH.
PARTS LIST FOR CRAFTSMAN 13" DRILL PRESS MODEL NO. 113.213130 FIGURE 2 PARTS LIST 8 10 \ 9 \ \ \ 7 3 \ 6 \ 42 14 15 21 38 20 37 21 22,,.,-'_(_ 36 30 33 34 35 31 32 29 28 27 26 ..
v PARTS LIST FOR CRAFTSMAN 13" DRILL MODEL NO. 113.213130 Always order by Part Number--Not FIGURE 2 PARTS PRESS ¢# by Key Number LIST ! Key I Pa_ No.
PARTS LiST FOR CRAFTSMAN 13" DRILL PRESS MODEL NO. 113.213130 13 Always order by Part Number--Not FIGURE Part No. Key No. 1 3 PARTS Key No. Description 817475 817351 817391 Tube-Column Rack Screw-Hex Soc. Set I M10x1.5-12 817476 Support-Column *Screw, Hex Hd. M10x 1.5-40 i STD836040 Base i 817508 i 817776 Support-Table w/Indicator 817348 , Crank 11 12 13 14 15 16 17 18 19 41 5 6 7 8 * Standard Hardware item -- May Be Purchased Loca!ly. 3O by Key Number LiST Part No.
NOTES 31
] LL SERVmCE Now that you have purchased your '13-inch Drill Press, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co. stores. Be sure to provide all pertinent facts when you call or visit, MODEL NO. !13o2!3!30 The model on a plate number attached of your "13-inch Drill Press will be found to the rear of the head.
