f Save This Manual For Future Reference SEAfR8 ownel"s manual MODEL NO. 113=221740 Serial Number. Model and serial numbers may be round at the rear of the base You should record botll model and serial number in a safe place for future use. FO 8 , Rt6/ 10 iNCH BENCH TOP TABLE SAW ®assembly , operating . repair parts YOUR ;AFETY READ ALL INSTRUCTIONS CAREFULLY \ J Sears, Pa_ NoSP5754 Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAW If within one year from the date of purchase, this Craftsman Table Saw fails due to a defect in material or workmanship, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERVICE CENTER/DEPARTMENT THROUGHOUT THE UNITED SIATESo This warranty applies only while this product is used in the United States, This warranty gives you specific state to state.
Before Each Use: inspect your saw. , To avoid injury from accidental starting, turn the switch off, unplug the saw, and remove the switch key before raising or removing the guard, changing the cutting tool, changing the setup, or' adjusting anything..
Safety Instructions (continued) • Use extra caution with large, very small or awkward workpieces: • Use extra supports (tables, saw horses, blocks, etc.) for any workpieces large enough to tip when not held down to the table top.
* Always use featherboards cuts+ IJI for any non thru rip type _,, i 24' While thru-sawing. . To avoid kickbacks and slips into the blade, always push forward on the section of the workpiece between the sawblade and the rip fence. Never push forward on the piece being cut off.+ _*_=.,_-.=. J==-...=o- Additional ! Crosscut Safety Instructions For: Type Cuts. Before starting. • Never use the rip fence whan crosscutting. FEATHERBOARDS • To avoid kickbacks and slips into the.
Glossary of Terms for Woodworking (continued) .......................... Rip Cut A cutting operation along the length of the workpiece. Sawblade Path The area of the workpJece or table top directly in line with either the travel of the blade or the part of the workpiece which will be, or has been, cut by the blade.. Set Thru-Sawing Any cutting operation where the blade extends pletely through the thickness of the workpiece.
4._Fusesmay "blow"or circuitbreakersmaytrip fre_ quentlyif: aMotor Is Overloaded. Ovedoading can occur' if you feed too rapidly or' make too many start/stops in a short time. b.Voltages not more than 10% above or below the nameplate voltage can handle normal loads. For heavy loads, however, the voltage at motor terminals must equal the voltage specified on nameplate. Overload Protection Your saw features a reset overload relay button.
Unpacking and Checking Contents Tools Needed Combination Square must be true. Check its accuracy as shown below. Draw light line on board alon edge #2 Phillips Screwdriver Select the straight edge of 314" thick board, This edge must be perfectly straight, Combination Square Medium Screwdriver [_L_.L! __-_ii, ----L _.--__ NOTE: The square and straight edge are used to align the saw, They must be accurate if the saw is to be aligned properly. r _ I._.
List of Loose Parts in the Box and Bags He)( Screw - 1/4-20 x I/2" (2) Shaft Wrench (1) Carriage Bolt - 1/4-20 x 7/8" (1) ..... , Ii,[,!lllllJl ilt; Arbor' Wrench (1) He× Screw _ 1/4-20 x 2-1/8" (1) Handle (Rip Fence) (1) Flat Washer' (1) © 114" External Knob (Handwheel) (1) kockwasher (4) Spreader Bracket Assembly (1) Nut Hex 5/16-18 (!) Wing Nut 1/4-20 (I) Assembling 1.Thread shown. screw Spreader Support (1) Switch Key (1) Handle to Handwheel .......................
Blade Guard Assembly .......... ' ...... 1. Frorn amongthe loose parts, locate the folk_wirlghardware: Hex Screw 114-20 x 1/2" (2) © 1/4" External Lockwasher (4) Hex Screw - 1/4-20 x 2-1/8" (1) Carriage Bolt - 1/4-20 x 7/8" (1) Q Flat Washer (1) G Wing Nut 114-20 (1) Spreader Support/1) Recessed / /.'f / /2 2. Position large recessed shoulder end of the spreader support against end of pivot rod and fasten to table using the 1/4-20x2-1/8" long hex screw and 1/4" external tooth Iockwasher.
Blade Guard Alignment ii IIII,Mlll IMPORTANT: To work properly, the spreader must always be adjusted so the cut workpiece will pass on either' side of the spreader without binding or'skewing to the side.
Rip Fence Assembly and Adjustment ........................... i WARNING: To prevent personal injury, always dis- i l adjustments. connect plug from power source when I making Q 1. Thread 5/16-18 nut all the way onto the fence locking handle 2, Thread rip fence locking handle into cam until tight,, Lock the nut against cam with wrench, 3 Place the rip fence on the table and lower' the rip fence locking handle until the rip fence is secure to front rail.
° Raisethe ripfencelockinghandle,moveandreturn the nipfence adjacentto the mitergaugegroove, lower'therip fencelockinghandle. • Repeatandrechecksteps8 and9 inthe"RipFence Assembly and Adjustment" sectien_ NOTE: To always obtain tile best atignment'of the 'rip fence, develop the habit of holding the front casting on the fence back against the table top while tightening the fence tock handle Tigilten the rip fence lock handle securely to prevent rip fence movement while sawing.
Blade Tilting Control and LOck Lever Adjustment 1. Loosen blade tilting lock lever and slide the _eievation handwheel until blade is at desired angle and tighten blade tilt lock lever_ iiiiiiii .Elevation ii iii , i, Handwheei !1 2. If blade lock lever' intederes with sorne object before blade tilting control mechanism is held tight or rigid, pull lock lever out and rotate lock lever counterclockwise to another position.. Tighten lock lever..
Blade Tilt Indicator Adjustment 1. With 90 ° positive stop set and blade tilt control pushed against this stop, loosen indicator screw, adjust indicator pointer to "0" degrees and retighten indicator screw Indicator Pointer NOTE: When making critical cuts, make a trial cut on scrap wood rather than relying on the tilt scale or stops.
Adjusting Blade Parallel to Miter Gauge Groove I WARNING: To avoid injury from accidental start,] make sure switch is "OFF" and plug is not con-I f netted to power source outlet. CAUTIoN: illllll Alignment Screws (A) Secondary Alignment Screws (B) I Fold a piece d. of cardboard over the blade j 1.,Unplug the saw.
Installing Sawblade ,H=HH = = 1.. Unplug the saw. Open End Arbor 2_ Install sawblade onto shaft with the top blade teeth pointing toward front of saw_ 3. Install blade collar with hollow surface toward blade Shaft Wrench_--"-_'_--_, i_ Closed End Wrench 4. Install arbor nut.. 5_ To tighten arbor nut, hold arbor' wrench against rear of table, push arbor nut wrench towards rear of table. Blade Arbor Nut __ NOTE: Arbor nut should just be snug.. Do not overtighten.
Mounting TableSaw to Workbench,Cabinetor Legset(continued) Workbench Mounting Using "C" Clamps An alternative method of securing your table saw is to fasten the saw base with "C" clamps._ 1. Follow instructions for mounting to workbench, substitutirig "C" clamps in each recessed mounting screw Iocation_ 2. Securely clamp saw to workbench using three or four "C" clamps, as shown.
Getting to Know Your Table Saw .... 11 Blade Guard 2 Table Insert 6 Blade Tilt Rip Fence "4 Table 7 Miter Gauge (stored position) Handwt 1 On-Off Rip Fence Storage Overload Protection 5 Base \8 Blade Tilt Scale Wrench Storage 3 Sawdust F Ejection Port Guard Storage on Non-thru Cuts 19
Getting to Know Your Table Saw (continued) ........... 1. On-Off Switch. I CAUTION: Before turning switch "oN;;; _ the blade guard is correctly installed and operating I properly. I The On-Off Switch has a locking feature, This feature is intended to help prevent unauthorized and possible hazardous use by children and others,, 2.
Work Feed Devices Slightly Before cutting any wood on your saw. study all of the "Basic Saw Operations" found on pages 23 through 33 Less Than Thickness of Workpiece Up to 318" 3/4 As you learn new table saw woodworking techniques you'll see that many types of cuts need different support and feeding devices, known as jigs or fixtures. They can help you make cuts more accurately By helping to steady the workpiece and keep you away from the blade, they can help you safely use,your saw for certain cuts.
Work Feed Devices (continued) ...... die , Position the handle in the center of the plywood base. Fasten them together with glue and wood screws_ IMPORTANT: Make sure the screw heads do not stick out tram the bottom oi tile base, they must be flush or recessed° The bottom must be flat and smooth enough to slide along the auxiliary fence you are now ready to make. "t-3/8" Plywood Base Auxiliary Fence Making the base: .
Safety instructions for Basic Saw Operations Before Each Use: inspect your work area. ° Keep work area clean. o Cluttered areas and benches invite accidents.. Floor must not be slippery from wax or sawdust. Inspect your saw.
Safety instructions for Basic Saw Operations (continued) Avoid accidental starting. ° Make sure switch is "OFF" before plugging saw into a power outlet. Plan your cut. * To avoid kickbacks and throwbacks - when a part or all of the workpiece binds on the blade and is thrown violently back toward the front of the saw: Whenever - Never cut freehand. Always use either a rip fence, miter gauge or fixture to position and guide the work, so it won't twist or bind on the blade and kickback.
Basic Saw Operations NOTE: The space between the miter gauge bar and the groove in the table is held to a minimum during manufacturing. Using the Miter Gauge The miter gauge is used when crosscutting, miter cutting, bevel cutting, compound miter cutting, dadoing and when rabbeting across the end of a narrow workpiece. For maximum accuracy when using the miter gauge, always favor one side of the groove in the table.
-Basic Saw Operations (continued) Repetitive Crosscutting Repetitive cutting is known as cutting a quantity of pieces the same length without having to mark each piece. • When making repetitive cuts from a long workpiece, make sure it is supported, WARNING" Never' use the rip fence as a length stop I because the cutoff piece could bind between the i fence and the blade causing a kickback. J 1.
Compound Miter Crosscutting Compound miter cutting is a combination of miter cutting and bevel crosscutting,. The cut is made at an angle other than 90 ° to both the edge and the bottom flat side of the wood. Adjust the miter gauge and tile blade to the desired angle_,oMake sure miter' gauge is locked. o Always use the miter' gauge in the groove to the right of the blade. It cannot beused in the groove to the left because the blade guard will interfere..
Basic Saw Operations (continued) Ripping Always Support Long Ripping is known as a cutting operation along the length of the workpiece. Workpiece_,J Position the fence to the desired width of rip and lock in place Before starting to rip, be sure: 1_ Rip fence is parallet to sawblade.. 2. Spreader' is properly aligned with sawblade. 3o Anti-kickback pawls are functioning properly. When ripping long boards or' large panels, always use a work support.
When "width ef rip" is narrower than 2", the push stick cannot be used because the guard wilt interfere° Use the auxiliary fence and push block for' this ripping operation. Attach auxiliary fence to rip fence with two "C" clamps_ Auxiliary Work Support/Fence Feed the workpiece by hand along the auxiliary fence until the end is approximately 1" past the front edge of the table° Continue to feed using the push block.
Basic Saw Operations (continued) ............................ Using Featherboards for Thru-Sawing Featherboards are not employed for thru-sawing tions when using the miter gauge, operaWork Supports Featherboards are used to keep the work in contact with the fence and table as shown, and to he!p stop kickbacks_ "=erboard Add a 7-1/2" high flat facing board to the full length of the fencer Mount featherboards to fence and table as shown.
Using Featherboardsfor Non Thru-Sawing Featherboards are not employed during non thru-sawing operations when using the miter gauge. Use featherboards for all other non tions (when sawblade guard must be boards are used to keep the work fence and table as shown and to stop Fea ps thru-sawing operaremoved).
Basic Saw Operations (continued) Rabbeting Rabbeting is known as cutting out a section of the corner of a piece of material, across an end or along an edge_ First Cut To make a rabbet requires cuts which do not go all the way through the material.. Therefore, the blade guard must be removed Rabbet 1.. Remove blade guard. 2. For rabbeting along an edge (long way of workpiece) as shown, add facing to rip fence approximately a,s high as the workpiece is wide.
installation and Operation of Mol To get full arbor nut engagement with the arbor ttlreads .... this saw requires a special molding head mounting arrangement Always arrange and mount the molding head as shown.
Maintaining Your Table Saw (continued) Lubrication The saw motor bearings and gear case have been packed at the factory with proper lubricant and require no additional lubrication_ The following parts should be oiled occasionally with SAE no. 20 or' no. 30 engine oil, Miter Gauge _ _ Assembly l r Elevation screw threads and pivot nuL 2_ Elevation bracket pivot points,, 3.
Troubleshooting ................... WARNING: To avoid injury from accidental start, turn switch "OFF" and always remove plug from the power'] source before trouble shooting. TROUBLE Excessive vibration Cut binds, burns or stalls motor when ripping. PROBABLE CAUSE REMEDY 1. Blade out of balancer. 1 Discard blade and use a different blade, 1_ Miter gauge not adjusted properly° 1. See "Adjustments" 1. Dull blade or' improper tooth set. 2o Warped board 1. Sharpen or replace blade. 2.
Repair Parts ....... Parts List for Craftsman 10" Bench Top Table Saw Model No. 113.
Repair Parts .... ...... _i ¸¸. Parts List for Craftsman!i(Y' B ¢h Top Model No:l 13.221740 Tabie Always Order by Pa_ Number:- Not KeyNumber Figure I Key Noo 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Part No 817357 i 822497 822498 822487-1 823170 823023 823022 823046 STD852004 56-100002 823047 823167 STD551025 60545 823042 823041 823044 823043 823086 823085 STD541031 823052 Key No.
Repair Parts .................................................................. Parts List for Craftsman 10" Bench Top Table Saw Model No. 113.
Repair Parts ....................................................... ......................... '" Parts List for Craftsman 10" Bench Top Table Saw Model No. 113.221740 Always Order by Part Number - Not Key Number Figure 2 I Key No.
L. .. Parts ,,,.................................................................. ,Tu,, Parts List for Craftsman Model Always 10" Bench Top Table Saw No. 113.221740 Order by Part Number Figure 4 19 21 18 ..i,l,ii ¸ - Not Key Number 22 23 \ 17 3 4 14 13 t2 11 Kev l No, J Part No 8 STD522505 STD551225 823181 82318O 823179 823178 823182 1823187 9 10 823069 STD510802 2_ 3t 41 51 61 1t i82a19o 12 1823189 10 6 Description No, Screw, He)( Hd.
Repair Parts .... ................ , Parts List for Craftsman 10" BenchTop Table Saw Model No. Always . 3.22174_ii, '_ Order by Part Number Figure 6 Part No.
p,-_L f ,,,,HIIHI 8WAIRS 10 INCH BENCH TOP TABLE SAW owner's rnanual MODEL NO. For the repair or replacement paris you need Call 7 am - 7 pro,7 days a week 113.
