r Save This Manual for Future Reference SEARS owner's manual Model No. 113.169240 ' Serial Number Model and serial number may be found on the back of the bracket-handle. You should record both model and serial number ina sere placefor future I:RRFTSMRN COMMERCIAL DUTY VAC CART use. Fits Most 16 Gallon Craftsman Wet Dry Vacs FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY • assembly • operating • repair parts • Seam, Part No. SP5389 Roebuck _,. • and Co., Hoffman Estates, Form No.
Introduction This cart is designed especially for use with Craftsman 16 gallonWetJDryVacs only. For best results, be sure to follow these instructions. Table of Contents Section Page Introduction.................................................................. 2 Table of Contents ........................................................ 2 Unpackingand Checking Contents ............................. 2 Listof Loose Parts .................................................... 2 Assembly ........................
Phillips Screwdriver Pliers If any parts are missing or damaged, stop and contact your Authorized Service Center, Do not assemble until you have all the parts. 1. Turn the drum upside down on the floor with the drain facing you. 2. Insert (2) caster feet into the bottom of drum as shown. Light taps with a hammer may be needed to fully seat the caster feet. 3. Locate the right and left hand legs. Separate the legs from the molded connection.Locate the right and left cradles.
Assembly (continued) 9. Mount (1) retaining ring onto one end of axle. Using pliers,snap retaining ring intogroove on axle. 10. Slide wheel onto open end of axle. 11. Slide open end of axle thru cradle left and left leg, making sure the leg slot lines up with the cradle hole. Slide all the way through the cradle rightand rightleg. Light taps with a hammer may be required to fully insert axle. Cradle Cradle Left Righ_ II Left Leg ..j_i Axle w/Wheel Open End 12.
16.Slide plastichandle bracket onto right and left legs. 17. Slide metal handle into (2) holes on plastic handle bracket. Metal Handle 18. Align holes in handle with hole in leg and plastichandle bracket. Plastic Handle Bracket f m h 0 19. Install (2) #10 x 314 screws into (2) holes on legs with (2) matching holes on handle for each side. NOTE: To adjust height, slide metal handle up till one hole is visible on each side. The (2) holes on legs should then line up with (2) holes on metal handle.
Assembly (continued) 20. Locate (2) tabs on plastic handle bracket and position (2) slots on tote, Slide tote down over (2) tabs on bracket. Tabs Handle Bracket ToteJ Slots WARNING: To reduce the risk of injury: Before Each Use • Check for missing, damaged or broken pads. Repair any damage and replace any missing parts before using cart. During Use To reduce the risk of being struck by or pulled down by a rolling vac: • Block the casters on any uneven or sloped surface before starting to vacuum.
Repair Parts Parts List for Vac Cart Model No. 113.169240 13\ I 6 10 i j 4\ Always order by Part Number - Not by Key Number Kay No 1 2 3 4 5 6 7 8 Part No. 818438 818437 818435 STD581050 809862 818431 818433 818439 Key No Description Handle Bracket, Handle Left Leg Ring, Retaining 112" 10" Wheel Axle Cradle, Left Caster Foot 9 10 11 12 13 Pa_ No.
#.- _ )1, #r SEARS COMMERCIAL DUTY VAC CART owner's manual Fortke repair or replecementparisyouneed (;all7 am - 7 pm, 7 daysa week Model No. 1-800-366-PAITT 113.169240, (1-800-360-7278) Forin-homemajorbrandrepair service Call24 hoursa day,7 daysa week 1-800-4-REPAIR (1-800-473-7247) The model number of yourCommercial Duty Vac Cart will be found on the back of the handle bracket.
