*'-Save This Manual For Future TM Reference SEARS owner's manual MODEL NO. 113.177600 Serial Number Model and serial numbers may be found on the handle. You should record both model and serial numbers in a safe place for future use. FORYOUR SAFETY CRRFTSMRN 12 GALLON FULL BLOWING WETIDRY VAC • assembly • operating • repair parts READ ALL INSTRUCTIONS CAREFULLY Sears, Roebuck Part No. SP6150 and Co., Hoffman Emtes, _ IL 60179 U.S.A. Printed in U.S.A.
y -,q FULL ONE YEAR WARRANTY ON CRAFTSMAN WET/DRY VACS If within one year from the data of purchase, this Craftsman Wet/Dry Vac fails due to a defect in matariai or workmanship, Sears will repair it, free of chan_e. If this Craftsman Wet/Dry Vac is used for commercial or rental purposes, this warranty coverage applies for only 90 days from data of purchase. WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERVICE CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES.
oexore unplugging. To reduce the risk of injury from accidental starting, unplug power cord before changing or cleaning filter. moving parts. To reduce the risk of falls, use extra care when cleaning on stairs. This Wet/Dry Vac is double-insulated, Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. eliminating the need for a separate grounding system. Use only identical Do not use with damaged cord, plug or other parts.
Introduction Owner's Manual Contents This Wet/Dry Vac is intended for household use only. IMPORTANT NOTE Please Read Carefully Static Shocks Are Common - In dry areas or when the relative humidity of the air is low. To reduce the fiequency of Item Page Warranty Information ............................. Safety Instructions ................................. Introduction ............................................ 2 2 4 • Unpacking and Checking Carton Contents .............................
Float/Cage Assembly WARNING: For your own safety, never connect plug to power source outlet until all ammbly steps are complete and you have read and understood the safety and operation Instructions. Do not operate vac with any parts damaged or missing. 1. Place the power assembly of vac NOTE: If filter cage needs to be removed, because the float is placed in the wrong way, use a slotted screwdriver and insert the blade near one of the tabs between the filter cage and the center ring of the lid.
Caster/Caster Foot Assembly 1. Remove the power assembly from the dust drum and set aside. 7. Turn the drum upright. 2. Tqrn the dust drum upside down on the floor. 3. Insert the caster feet into the bottom of drum, as shown (4 places). 4. Push on the caster foot until the foot is flush with bottom of the dust drum. Caster--,. Foot 5. Insert the caster stem into the socket of Pin the caster foot, as shown (4 places). 6.
NOTE: The swivel end of the hose is removable if more hoses need to be 6. Insert the soft end of the hose, which is opposite the swivel end, intothe vacuum port directly above the drain. attached for more length from the vac. To remove the swivel portion of the hose, 7. Place the utility nozzle securely on the swivel end of the hose and the vac is ready for use. grasp the hose swivel and firmly pull it out of the flexible hose.
Operation WARNING To reduce flammable the risk of fire or explosion, gases, vapors or explosive do not operate this vac IRareas dust in the air. Flammable with gases or vapors include but are not limited to; fighter fluid, solvent type cleaners, oilbase paints, gasoline, alcohol or aerosol sprays. Explosive dusts include but are not limited to; coal, magnesium, grain or gun powder. Do not vacuum explosive dust, flammable or combustible liquids or hot ashes.
Moving the Vac Emptying the Drum 1. Should it become necessary to pick the Injury from accidental starting, . unplug power cord before emptying I WARNING: To reduce the risk of the drum. vac up to move it, DO NOT pick the vac up by the lid handles unless dust drum is empty. To avoid dropping the-vac due I to latches releasing or possible part breakage, pick the vac up by the lip of the dust drum. 1. The vac comes equipped with a drain for easy emptying of liquids.
Maintenance Filter IMPORTANT," To avoid damage to the blower wheel and motor, always reinstall the filter before using the vac for dry material pickup. Injury from accidental starting, unplug power cord before changing I ARNING: To reduce the risk of or cleaning filter. Dry Filter 1. Some removal of dry debris can be accomplished without removing the filter from the vac. Slap your hand on top of the power assembly while the vac is turned off.
Wet Nozzle farthest from you.) To pick up liquids off a smooth surface, use the 2-1/2" wet nozzle accessory supplied with your wet/dry vec. To use this nozzle, simply attach the nozzle to the end of an extension wand. Connect a second extension wand to the first, and connect the 2-1/2" x 7' hose to the extension wand. _. t _= _= • - " _" _" I " "- - W - -" _ ! 2. Using both hands,, lower the nozzle body onto the insert and squeegee with the round opening of the nozzle closest to you.
Repair Parts 12 Gallon Wet/Dry Vac Model Number 113.177600 Always order by Part Number - Not by Key Number WARNING SERVICING OF DOUBLE-INSULATED WETIDRY VAC In a double-insulated Wet/Dry Vac, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added.
Repair Parts 12 Gallon Wet/Dry Vac Model Number 113.
CRAFTSMAN® Accessories and Attachments Get more versatility from your Craftsman wet/dry vacuum by adding these accessolies. Additional wet/dry vac accessories may be purchased at your local Sears retail store or Sears/CraRsman Power and Hand Tool Catalog.
16934HoseGrip 16917HoseJoiner 16930HoseLock 16935Gutter Nozzle Sawdust Collection Series Whole-shop Sawdust Manifold-Type 29964 Collection System Table Saw Dust Collection Kit 29962 Radial Arm Saw Dust Collection Kit 29963 15
For the repair or replacement paols you need Call 7 am - 7 pro, 7 daysa week 1-800-366-PART (1-a00-366-7278) For in-home majorbrand repair service Call 24 hours a day,7 daysa week 1-8OO-4-REPAIR (1-800-473-7247) For tile location of a Seats Repair Service Center in your area Call 24 hoursa day,7 daysa week 1-800-488-1222 g|g||g For iMormation on pmchaslnga Sears Maintenance Agreementor to inquire about an existingAgreement Call 9 am - 5 pro, Monday-Saturday 11-800-827-6655 SE,dLRS America's Repair
