Manual

unpacking and checking contents
CONTENTS
UNPACKING AND CHECKING CONTENTS .... 6
ASSEMBLY
Installing Sawdust Elbow ................ 7
Assembling Steel Legs .................. 8
Installing Table ...................... 8
Motor Pulley Belt Guard and Motor Installation . 9
Check Motor Rotation .................. 10
Mounting Motor ...................... 10
Attaching Belt Buards .................. 11
Installing The Blade ................... 12
Adjusting The Table ................... 16
On-Off Switch ....................... 16
GETTING TO KNOW YOUR BAND
SAW/SANDER ........................ 18
Adjustment Diagrams .................. 18
Tension Adjustment Knob ............... 18
Tension Scales ....................... 18
TOOLS NEEDED
Table Tilting ........................ 18
Blade Guide Adjustment ................ 18
Lateral Guide Adjustment ............... 18
Blade Thrust Bearing Adjustment .......... 18
Guide Bar Lock Screw .................. 18
Guide Bar .......................... 19
Installing Sanding Attachment ............ 19
BASIC BAND SAW/SANDER OPERATION ..... 21
Sawing ............................ 21
Sanding ........................... 21
MAINTENANCE ....................... 22
Tires ............................. 22
General ............................ 22
Motor ............................. 22
Lubrication ......................... 22
Recommended Accessories............... 22
TROUBLE SHOOTING ................... 23
REPAIR PARTS ....................... 23
SMALL SCREWDRIVER
MEDIUM SCREWDRIVER
COMBINATION SQUARE lJ_r_
7/16 INCH WRENCH
3/8 INCH WRENCH
3/4 INCH WRENCH
COMBINATION SQUARE MUST RE TRUE
DRAW LIGHT
LINE ON BOARD
ALONG THIS EDGE
STRAIGHT EDGE OF
BOARD 3/4" THICK
THIS EDGE MUST BE
PERFECTLY STRAIGHT
Model 113.243401 Band Saw/Sander is shipped complete
in one carton but DOES NOT INCLUDE Steel Legs or
Motor.
Model 113.243411 Band Saw/Sander is shipped complete
in one carton and INCLUDES Steel Legs and Motor.
Separate all parts from packing materials and check each
item with illustration and "Table of Loose Parts." Make
certain all items are accounted for, before discarding any
packing material.
If any parts are missing, do not attempt to assemble the
band saw, plug in the power cord or turn the switch on
until the missing parts are obtained and installed correctly.
/
SF!OULD BE NQ GAP OR OVERLAP HERE WHEN
SQUARE IS FLIPPED OVER IN DOTTED POSITION,
A
/
H
ITEM TABLE OF LOOSE PARTS QTY.
A
B
C
D
E
F
G
H
J
Basic Saw Assembly ..................... 1
Owner's Manual ........................ 1
Saw Table ............................. 1
1/2 x 52-1 n. V-Belt ...................... 1
Carton containing Belt Guard, Belt-Guard Support,
Support Bracket, three Clips and three Self-
"rappi ng Screws ........................
1/2-1n. Sanding Belt .....................
1/4-In. Band Saw Blade
Sawdust Elbow .........................
Two Bags containing the following items:
Set Screw Wrench, 1/8"
Set Screw Wrench, 5/32" . ...............
Set Screw Wrench, 3/16"
Flat Washer, 1-1/8" diameter .............
Trunnion Locknut
Pan Hd. Mach. Screw, Self Tap, 10-32 x 3/8"
Pan Hd. Math. Screw, Self Tap, 8-32 x 3/8" .
Soc. Hd. Setscrew, Flat Pt., 5/16-18 x 3/8" .
Flat Hd. Mach. Screw, 6-32 x 7/!6" . .......
Hex Nut, 6-32 .........................
Split Lockwasher, No. 6 .................
Tilt Pointer
Tube Clamp ..........................
Rubber Gasket (strip) ...................
Alignment Plate .......................
Motor Pulley, 2-1/2" . ..................
Sanding Platen ........................
Cord Clamp ..........................
Table Insert ..........................
Tilt Lock Handle (Wrench) ...............
Spacer ...............................
Blade Tension Knob ....................
Switch Key ...........................
Flat Washer, 9/32 x 5J8 x 1/16 ............
Screw Truss Hal., 1/4-20 x 1 ..............
Wing Nu_, lj4-20 ...................... =
2
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1