,';o’"" - rTT) ‘ -/T^,,1 - —- - -'- Owners Manual Garage Door Opener Model 139.535006 CAUTION: READ INSTRUCTIONS AND RULES FOR SAFE OPERATION CAREFULLY. FASTEN THIS MANUAL NEAR THE GARAGE DOOR AFTER INSTALLATION. PERIODIC CHECKS OF OPENER ARE REQUIRED TO INSURE SATISFACTORY OPERATION. IWDEX Features of Your Opener_____ . . . . Specifications ................. . You’ll Need Tools...................... . Safety Rules —........... ................ .. Carton Check List_____ _ Accessories................
FEATURES OF YOUR OPENER , Opener Lights: Turn on and off automatically, with 4-1/2 minute illumination for your safety and convenience. Provide constant light when Work Light control button is pressed,, , Safety System: Independent up and down force adjustment Door reversesautomatically when ob structed in DOWN direction Door STOPS when obstructed in UP direction. Emergency Disconnect: Pull cord disconnect permits rnanuai door operation.
Start By Reading These Important Safety Rules THIS SAFETY ALERT SYMBOL MEANS CAUTION - PERSONAL SAFETY OR PROPERTY DAMAGE IN STRUCTION, READ THESE INSTRUCTIONS CAREFULLY.
CARTON CHECK LIST SEARS has packaged your Garage Door Opener in two cartons THE RAIL ASSEMBLY CARTON CONTAINS; a three-piece rail, two hanging straps, straight door arm section* and rail assembly hardware.
Accessories Sears offers many useful accessories foryour garage door opener. They are illustrated below with Sears stock num bers and descriptions. ............................. ............................................................................... .................... EXTRA TRANSMITTER: Includes visor clip.
Assembly TO AVOID INSTALLATION DIFFICULTIES, DO NOT RUN THE GARAGE DOOR OPENER UNTIL YOU HAVE COMPLETED STEPS, PAGE 15. SXE P 1 Assemble Tee Rail & Attach Cable Pulley Bracket TEE RAIL BACK CTO CHASSIS) CAUTION: Do not tighten the lock nuts until bolt necks are seated in square holes. Tee Rail (End Seciiors) Carriage Bolt 1/4"-20x1/2" Flange Tee Rail (Center Section) PROCEDURE: Place the 3 Tee rail sections on a fiat surface for assembly. THIS IS IM PORTANT.
Assembly STEP 2 Connect Trolley & Attach Chain Retainer Bracket Asa temporary stop, inserta screwdriver into Tee rail as shown. Slide the inner trolley onto the Tee rail, as shovi/n, until it is firmly against the screw driver. Slide the outer trolley onto the Tee rail until it partially engages the inner trolley and stops, TO FULLY ENQAGE TROLLEY: With a hammer, firmly tap the back end of outer trolley just below the rail guide.
Assembly STEP 4 Install Chain and Cable DO NOT REMOVE CHAIN AND CABLE FROM DIS-^ PENSER CARTON. Master Link Clip-On Spring Detach cable from side of car ton and fasten to tr olley with a master link from coin envelope, MASTER LINK PROCEDURE: Push pins of master link bar through loop of cable and hole in flat end of trolley shaft Push cap onto pins and into notches Slide clip-on spring over cap and into pin notches until both pins are locked in place.
Assembly STEPS Tighten the Chain and Cable dAUTIONt Keep chain from twisting as nuts are turned. Loosen Inner Tighten Outer PROCEDURE: Connect chain and cable to threaded shaft of trolley in the order itiustrated: inner nut, lockwasher, chain retainer bracket and outer nut Tighten the chain and cable by threading outer nut toward trolley. Chain is properly tightened when it is approximately 1/2" above the base of Tee rail midway between cable pulley bracket and chassis.
Installation Completed installations of header bracket, door bracket with plate and door arm (depending on door type) are shown below,. The header bracket supports the front end of the Tee rail, The door bracket connects door arm to trolley, IT IS RECOMMENDED THATTHE OPENER BE INSTALLED 7 FEETOR MORE ABOVE THE FLOOR WHERE SPACE PERMITS. Follow only those instructions which apply to your door type as shown on Page 5.
Installation STEP 2 Position & Install Header Bracket THE HEADER BRACKET MUST BE RfGIDLY FASTENED TO THE HEADER WALL OR CElLtNG. REINFORCE WALL OR CEILING WITH 2x4 IF NECESSARY. INSTALLATION Locate height for header bracket by opening door to highest point of travel as shown.
Installation STEPS Attach Tee Rail to Header Bracket PROCEDURE: Position opener chassis on garage floor below door and header brackets. Use packing material base to protect cover, iSiOTE: To enable Tee rail to clear sectional door springs, it may be necessary to lift the chassis onto a temporary support. CAUTION: Chassis must either be secured to sup port or held firmly in place by another person.
Installation STEPS Hang Opener Chassis THE OPENER CHASSIS MUST BE ATTACHED TO A STRUCTURAL SUPPORT OF THE GARAGE, Three representative installations are shown. Yours may be different Hanging brackets should be angled to pro vide rigid support PROCEDURE: On EACH side of opener measure the distance from chassis to structural support Cut both pieces of the hanging bracket to required lengths.
Installation STEP? Instali Wall Control Top (astaliaHon Flange INSTALL WALL CONTROL (OR ADDITIONAL PUSH BUTTONS) OUTOFTHE REACH OFCHILDREN, DO NOT ALLOW CHILDREN TO OPER ATE WALL CONTROL OR TRANSMITTER. SERIOUS PERSONAL INJURY FROM A CLOS ING GARAGE DOOR MAY RESULT FROM ANY MISUSE OF OPENER. FASTEN THE CAUTION LABEL ON THE WALL NEAR THE WALL CONTROL AS A REMINDER OF SAFE OPERATING PROCEDURES.
Installation STEPS Coimect Eiectric Power TO AVOID SERIOUS PERSONAL INJURY FROM ENTANGLEMENT, REMOVE ALL ROPES CONNECTEDTO THE GARAGE DOOR BEFORE OPERATING DOOR OPENER. REMOVE EXISTING GARAGE DOOR LOCKS OR USE A WOOD SCREW OR NAIL TO MAKE THEM INOPERATIVE, INSTALLATION AND WIRING MUST BE IN COMPLIANCE WITH LOCAL BUILDING AND ELECTRICAL CODES.
Installation STEP 10 Connect Door Arm to Trolley SECTIONAL DOOR INSTALLATION ONLY PROCEDURE: Fasten straight door arm section to trolley and wedge door arm section to door bracket, as shown (A). Insert and spread a cotter pin to secur e each connection,. B Bring the door arm sections together. Find a pair of holes that line up and join sections as shown (B). INSTALLATION FOR SECTIONAL DOOR IS COMPLETE. PROCEED TO ADJUSTMENT STEP 1, PAGE 18.
Installation STEP 11 Adjust Limits (Ail One-Piece Doors Only} CAUTION; To prevent damage to garage doors, the opener limits must be adjusted on ALL ONEPIECE DOORS, Limit Adjustment settings regulate the points at which door will stop when moving up or down. Repeated operation of theopenerduring adjustment may cause the motor to overheat and shut off. Simply wait 15 minutes and continue adjustments. Limit adjustment screws are located on the left side panel of the openeras shown.
Adjustment STEP1 Adjust UP and DOWN Limits The limit adjustment screws are located on the left side panel of the opener chassis as shown LI MIT ADJUSTMENT settings regulate the points at which the door will stop when moving up or down NOTE: Door STOPS in UP direction if anything interferes with door travel. Door REVERSES in DOWN direc tion if anything interferes with door travel (including binding or unbalanced doors).
Adjustment STEP 2 Adjust Force nn wrjT force ADJUSTMENTS iJcE^lil fStcE wfLUOTM OR DAMAGE THE GARAGE DOOR. TO COMPENSATE FOR A BINDING OR STICKING GARAGE DOOR. OPERATION OFTHE SAFETY REVERSE SYSTEM Force Adjustment Controls are located on right side panel of the opener chassis FORCE ADJUSTMENT settings regulate the amount of power required to open and close the door. Force ■Adiustment Controls NOTE: Door STOPS In UP direction if anything interferes with door travel.
Adjustment STEFS Test Safety Reverse System THE SAFETY REVERSE SYSTEM TEST IS IMPORTANT. THE GARAGE DOOR MUSTREVERSE ON CONTACT WITH AONE INCH OBSTACLE PLACEDON THE FLOOR. FAILURETO PROPERLY ADJUSTTHE OPENER MAY RESULT IN SERIOUS PERSONAL INJURY FROM ACLOSING GARAGE DOOR. REPEATTHE TEST AT LEAST ONCE A YEAR AND MAKE ANY NEEDED ADJUSTMENTS, PROCEDURE: Place a 1-inch obsiacle on the floor under the garage door. Operate the door in the DOWN direction. The door must reverse on the obstruction.
Operation of Your Opener CAUTION: ® START BY READING THE SAFETY RULES ON PAGE 3. ® READ THE OPERATING INSTRUCTIONS ON THIS PAGE CAREFULLY. © DO NOT PERMIT CHILDREN TO PLA Y IN AREA OF DOOR. © OPERATE ONLY WHEN OPENER IS PROPERLY ADJUSTED AND DOOR IS IN SIGHT AND FREE OF OBSTRUCTIO THE SAFETY REVERSE SYSTEM IS IMPORTANT (SEE PAGE 20). GARAGE DOOR MUST REVERSE ON CONTACTWITHAONE-INCH OBSTACLE PLACEDONTHEFLOOR.FAILURETO PROPERLY ADJUSTOPENERMAY RESULT IN SERIOUS PERSONAL INJURY FROM A CLOSING GARAGE DOOR.
Radio Controls RECEIVER RADIO CONTROLS consist of a transmitter and a receiver. The transmitter sends a coded signal from outside the garage. The receiver is fastened to the right side panel of the door opener, it receives the transmitted signal and starts the door opener. The signal code is set at the factory Page 23 des cribes code changing procedures, if required. Self service of radio controls is not recommended, if service is needed, contact your nearest Sears Ser vice Center. Terminais .
Radio Controls Sears Trinary Radio Control Manulactured under 1 or more oi Ure following li S. patents: 3 445 848: 3 906.348; and 4 037 201 The coded signal in Sears Trinary RadioControls can be changed easily without the aid of aserviceman.The only tool needed Is a flat blade screwdriver Choose your own code by changing position of switches numbered 1 through 9 on the receiver code switch block. Changing the position of only one switch makes an entirely different code.
Having a Problem? OPENER DOESN’T ACTIVATE DOOR OPENS AND CLOSES BY ITSELF T Have you removed all door locks and bolts? 2 Does the opener have electric power? Check wall switch, fuse, etc. 3. Is there a broken wire between Wall Control and opener? Check under staples (A positive check can be made by temporarily installing another wire) 4. Are wiring connections correct? Refer to Step 7, Page 14. 5. Repeated operation may have tripped the over load protector in the motor. Wait 15 minutes.
Wiring Diagram and Receiver Schematic 25
INSTALLATION PARTS LIST KEY NO 1 2 3 4 5 6 7 8 9 10 11 PART NO.
Repair Parts Chassis Assembly Parts List KEY PART NO. NO. 1 2 31C290 41A2827 3 41A2817 4 5 41B2S91 41C2725 41A3063 6 7 41A3073 KEY PART NO. NO.
Owners Manual V -r 3)-r’-y i/ éü u\x ltJ Li ^ Al JMJ tJlJ ii VJ® HOW TO ORDER REPAIR PARTS Garage Door Opener Model 139.535006 Now that you have purchased your Sears Garage Door Opener, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co, stores. Be sure to provide all pertinent facts when you call or visit The MODEL NUMBER of your garage door opener is printed on a label located on the right side panel of the opener chassis.