Owner's Manual CRAFTSMAN SMART CONTROL = SMART GARAGE DOOR OPENER For Residential Use Only MODEL 139.54931 CERTIFIED Read and follow all safety rules and operating instructions before first use of this product. Fasten the manual near the garage door after installation. Periodic checks of the opener are required io ensure safe operation. DO NOT install on a one-piece door if using devices or features providing unattended close. Unattended devices and features are to be used ONLY with sectional doors.
TABLE OF CONTENTS introduction Safety symbol review and signal word review... LLL 3 Unattended Operation Preparing your garage door Test the Wi-Fi® Strength in Your Garage Tools needed Planning... coven Carton inventory. u. LL. Hardware inventory ce Assembly 10-13 Assemble the tall and install the trolley 10 Fasten the rail to the motor unit install the idler pulley install the belt... Tighten the belt. . install the sprocket cover... Lo...
INTRODUCTION Safety Symbol Review and Signal Word Review This garage door opener has been designed and tested to offer safe service provided it is installed, operated, maintained and tested in strict accordance with the instructions and wakings contained in this manual. When you see these Safety Symbols and Signal Words on the following pages. they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them.
Preparing your garage door Before you begin: 1. Disable Jocks and remove any ropes connected to the garage door, 2. Lift the door halfway up. Release the door. if balanced, it should stay in place, supported entirely by its springs. 3. Raise and lower the door to check for binding or sticking. if your door binds, sticks, or is out of balance, call a trained door systems technician, 4. Check the seal on the bottom of the door.
Test the Wi-Fi® Signal Strength in your garage You will need a router with WI-Fi and a smartphone or other motile device. Make sure your mobile device is connected to your WI-Fi network. Hold your mobile device in the place where your garage door opener will be installed and check the WI-Fi signal strength. Tools needed During assembly, installation and adjustment of the opener, instructions will call for hand tools as illustrated below. Check Signal Strength. If you ses: Py Ry WI-Fi signal is strong.
Planning Identify the type and height of your garage door. Survey your garage area to see if any of the conditions below apply to your installation. Additional materials may be required. You may find it helpful to refer back to this page and the accompanying illustrations as you proceed with the installation of your opener. Depending on your requirements, there are several installation steps which may call for materials or hardware not included in the carton.
Planning (Continued) ONE-PIECE DOOR INSTALLATIONS » Generally, a one-piece door does not require reinforcement. Hf your door is lightweight, refer to the information relating to sectional doors in Installation Step 8 Depending on your doors construction, you may need additional mounting hardware for the door bracket (Step 8). . Without a properly working safety reversal system, persons {particularly small children) could he SERIOUSLY INJURED or KILLED by a closing garage door.
Carlton inventory Your garage door opener is packaged in one carton which contains the motor unit and all parts illustrated below Accessories will depend on the model purchased. if anything is missing, carefully check the packing material.
Hardware Inventory Separate all hardware and group as shown below for the assembly and installation procedures.
ASSEMBLY STEP 1 Assemble the Rail and Install the Trolley To avoid installation difficulties, do not run the garage door opener until instructed prevent INJURY from pinching, keep hands and fingers away from the joints while assembling the mil. The front rail has a cut out “window” at the door end. The front rail has a rail tab. This tab MUST be on the top of the rail when assembled. 1.
ASSEMBLY STEP 3 Install the Idler Pulley 1. Lay the belt beside the rail, as shown. Grasp the end with the hooked trolley connector and pass approximately 127 (30 om} of belt through the window. Keep the ribbed side toward the rail, and allow it to hang until Assembly Step 4. 2. Remove the tape from the idler pulley. The inside center should be per-greased. if diy, re grease to ensure proper operation. 3. Place the idler pulley into the window as shown. 4.
ASSEMBLY STEP 4 Install the Belt 1. 2. Pull the belt around the idler pulley and toward the trolley. The ribbed side must contact the pulley. Hook the trolley connector into the retaining slot on the trolley as shown (Figure 1). With the trolley against the screwdriver, dispense the remainder of the helot along the rail length toward the motor unit and around the sprocket (Figure 2). The sprocket teeth must engage the belt. . Check to make sure the belt is not twisted.
ASSEMBLY STEP 6 Install the Sprocket Cover 1. Position the sprocket cover over the sprocket as shown and fasten to the mounting plate with 8x3/8" hex screws provided. You have now finished assembling your garage door opener. Please read the following wakings before proceeding to the installation section. HARDWARE SHOWN ACTUAL SIZE ‘sprocket cover) INSTALLATION To avoid possible SERIOUS INJURY to finger from moving garage door opener: « ALWAYS keep hand clear of sprocket while operating opener.
INSTALLATION STEP 1 on Determine the Header Bracket Location on — Tam FRONT : ” =) vor es ioe To prevent possible SERIOUS INJURY or DEATH: Header Wall » Header bracket MUST be RIGIDLY fastened to structural \ Vertical Tormenting support on header wall or ceiling, otherwise garage door of vicarage Door might NOT reverse when required. DO NOT install header Structural bracket over drywall Supports « Concrete anchors MUST be used if mounting header bracket ~ or 2x4 into masonry.
INSTALLATION STEP 2 Install the Header Bracket You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header racket over drywall. If installing into masonry, use concrete anchors (not provided). WALL HEADER BRACKET INSTALLATION 1.
INSTALLATION STEP 3 Attach the Rail to the Header Bracket Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way, you will need help. Have someone hold the opener securely on a temporary support to slow the rail to clear the spring. Position the rail bracket against the header bracket. Align the bracket holes and join with a clevis pin as shown. 1 © Insert a ring fastener to secure.
INSTALLATION STEP 4 Position the Opener Follow instructions which apply to your door type as illustrated. To prevent damage to garage door, rest garage door opener rail on 2x4 placed on top section of door, SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK A 2x4 laid flat is convenient for setting an ideal door to-rail Figure 1 distance. 1. Raise the opener onto a stepladder. You will need help at this point if the ladder is not tall enough. or 2.
INSTALLATION STEP 5 Hang the Opener Three representative installations are shown. Yours may be different. Hanging brackets should be angled (Figure 1) to provide rigid support. On finished ceilings (Figures 2 and 3), attach a sturdy metal bracket to structural supports before installing the opener. This racket and fastening hardware are not provided. 1. Measure the distance from each side of the motor unit to the structural support. 2. Cut both pieces of the hanging bracket to required lengths. 3.
INSTALLATION STEP 6 Install the Lights 1. Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens. 2. Insert an A19 incandescent (100 watt maximum) or compact fluorescent (26W, 100W equivalent) light bulb into the light socket. The lights will tum ON and remain lit for approximately 4-1/2 minutes when power is connected Then the lights will tum OFF. 3. Reverse the procedure to close the lens.
INSTALLATION STEP 8 Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or an the following page. A horizontal reinforcement brace should be {ong enough to be secured to two or three vertical supports. A vertical reinforcement brace should cover the height of the top panel. Figure 1 shows one piece of angle iron as the horizontal brace, For the vertical brace. 2 pieces of angle iron are used to create a Shaped support.
Fasten the Door Bracket (Continued) ONE-PIECE DOORS Please read and comply with the wakings and reinforcement instructions on the previous page. They apply to one-piece doors also. + Center the door bracket on the top of the door, in line with the header bracket as shown. Mark either the left and right, or the top and bottom holes. + Metal Doors: Dill 3/18" pilot holes and fasten the bracket with the self-threading screws provided. « Wood Doors: Dill 5/18" holes and use carriage bolts.
INSTALLATION STEP 9 Connect Door Arm to Trolley Follow instructions which apply to your door type as illustrated helot and on the following page IMPORTANT: The groove on the straight door arm MUST face away from the curved door arm (Figure 4). SECTIONAL DOORS ONLY 1. Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley. Slide the outer trolley back {away from the pulley) about shown in Figures 1, 2 and 3.
Connect Door Arm to Trolley (Continued) ALL ONE-PIECE DOORS IMPORTANT: The groove on the straight door arm MUST face away from the curved door arm (Figure 5). 1. Close the door. Disconnect the trolley by pulling the emergency release handle. Fasten the straight door arm and the curved door arm together fo the longest possible length (with hole overlap). . Attach the straight door arm to the door bracket using the clevis pin. Secure with the ring fastener.
INSTALLATION STEP 11 Install the Door Control INTRODUCTION NOTE: Older Craftsman door controls and third party products are not compatible Your garage door opener is compatible with up to 2 Smart Garage Door Opener door controls. install the door control within sight of the door at a minimum height of 5 feet {1.5 m) where small children cannot reach, and away from the moving parts of the door. NOTE: For gang box installations jt is not necessary to dill holes or install the drywall anchors.
INSTALLATION STEP 12 Install The Protector Stent IMPORTANT INFORMATION ABOUT THE SAFETY REVERSING Be sure power is NOT connected to the garage door opener SENSORS BEFORE installing the safety reversing sensor. The safety reversing sensors must be connected and aligned To prevent SERIOUS INJURY or DEATH from closing garage correctly before the garage door opener will move in the door: down direction.
Install The Protector System® (Continued) INSTALLING THE BRACKETS Be sure power io the opener is disconnected. Install and align the brackets so the sensors will face sate other across the garage road, with the beam ne higher than 6" {15 crm) above the floor. They may be installed in one of three ways, as follows. Garage door track installation (preferred); 1. Slip the curved arms over the rounded edge of each door track, with the curved arms facing the door. Snap into place against the side of the track.
Install The Protector System® (Continued) MOUNTING AND WIRING THE SAFETY REVERSING SENSORS Mounting: 1. Slide a carriage bolt head into the slot on each sensor. Use wing nuts fo fasten sensors to brackets, with lenses pointing toward each other across the door. Be sure the lens is not obstructed by a bracket extension (Figure 5). 2. Finger tighten the wing nuts. Option A Installation Without Pr-Witing: 1. Run the bell wire from both sensors to the garage door opener.
INSTALLATION STEP 13 Electrical Requirements To avoid installation difficulties, do not run the opener at To prevent possible SERIOUS INJURY or DEATH from this time. electrocution or fire: To reduce the risk of electric shock, your garage door opener has « Be sure power is NOT connected to the opener, and a grounding type plug with a third grounding pin. This plug will disconnect power to circuit BEFORE removing cover to ably fit into a grounding type outlet.
INSTALLATION STEP 14 a Aligning the Safely Reversing Sensors The door will not close if the sensors have not been installed Figure 1 and aligned correctly. When the light beam is obstructed or misaligned while the door is closing, the door will reverse and the garage door opener lights will flash ten times. If the door is already open, it will not close 1. Check to make sure the LED in both sensors are glowing steadily. The LED in both sensors will glow steadily if they are aligned and wired correctly.
ADJUSTMENT Introduction Your garage door opener is designed with electronic controls to make setup and adjustments easy. The adjustments allow you to program where the door will stop in the open (UP) and close (DOWN) position. The electronic controls sense the amount of force required to open and close the door. The force Is adjusted automatically when you program the travel. NOTE: if anything interferes with the door's upward travel it will stop.
ADJUSTMENT STEP 1 Program the Travel 1. Press and hold the Adjustment Button until the UP Button begins to flash and/or a beep is heard. 2. Press and hold the UP Button until the door sin the desired UP position. NOTE: The UP and DOWN Buttons can be used to move the door up and down as needed. 3. Once the doorstepping desired UP position press and release the Adjustment Button. The garage door opener lights will flash twice and the DOWN Button will begin to flash.
ADJUSTMENT STEP 2 Test the Safety Reversal System TEST 1. With the door fully open, place a 1-1/2 inch (3.8 cm) board {or a 2x4 laid flat) on the floor, centered under the garage door. 2. Operate the door in the down direction. The door MUST reverse on striking the obstruction. ADJUST + If the door steps and does not reverse on the obstruction, the down travel needs to be increased (refer to Adjustment Step 1).
BATTERY BACKUP Install the Battery 1. 2. Unplug the garage door opener. Open the light lens on the right side panel of the garage door opener. Use a Phillips head screwdriver to remove the battery cover on the garage door opener. Partially insert the battery into the battery compartment with the terminals facing out. Connect red and black wires from the garage door opener to the corresponding terminals on the battery. Replace the battery cover. Plug in the garage door opener.
SMARTPHONE CONTROL Get Connected ...and control your garage door opener with the Craftsman Garage Door app. You will need: + Smartphone or tablet + Broadband interment connection » Strong WI-Fi signal in the garage, see page 5 + Password for your home network « Craftsman serial number located on the garage door opener 1. ACTIVATE "WI-Fi LEARN" MODE Press and release the yellow LEARN button on the garage door opener 3 times. The garage door opener will beep once and a blue light will flash.
OPERATION IMPORTANT SAFETY INSTRUCTIONS ZA WARNING To reduce the risk of SEVERE INJURY or DEATH: 1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS. 9. After ANY adjustments are made, the safety reversal system 2. ALWAYS keep remote controls out of reach of children. MUST he tested. NEVER permit children to operate or play with garage door 10. Safety reversal system MUST be tested every month. Garage control push buttons or remote controls. door MUST reverse on contact with (3.8 cm) high 3.
Features Your garage door opener is equipped with features to provide you with greater control over your garage door operation. TIMER-TO-CLOSE (DO NOT enable on one-piece doors) The Timer-to-Close feature automatically closes the door afters specified time period that can be adjusted using the door control. Prior to the door closing teeth will be an audible and visual alert.
Door Control SYNCHRONIZE THE Dion control: To Synchronize a on the Garage Go a ple the push bar unt the game door opener activates may ae untold please et the dor control by pressing the push Sachs prose of the pus ba wll delegate te gee dost opener. USING THE DOOR CONTROL Navigation Screen GHT Button r= Notion Sensor Push Bar Press the push bar to open or close the door. Light Button Press the LIGHT button to turn the garage door opener lights on or off.
Smart Control Panel Setup SCREEN AND MENU NAVIGATION The main screen displays the time, temperature, and current battery charge {if applicable). The features on the door control can be programmed through a series of menus on the screen and the navigation buttons. Refer to the descriptions below. FEATURES Press the navigation button below “MENU” to view the Features menu. Clock Se tap: Sst the time, choose 12 or 24 hour clock and showy hide clock.
Programming Your garage door opener has been programmed at the factory to operate with your remote contra. Older Craftsman accessories are not compatible, see page 46 for compatible accessories. Programming can be done through the door control or the meal button on the garage door opener. To program additional remote controls refer to the instructions provided with the additional remote controls.
To Erase the Memory ERASE ALL REMOTE CONTROLS AND KEY LESS ENTRIES 1. Press and hold the learn button on garage door opener until the learn LED goes out {approximately 6 seconds), All remote control and key less entry codes are now erased. Reprogram any accessory you wish to use. ERASE ALL REMOTE CONTROLS, KEY LESS ENTRIES AND SMART CONTROL DEVICES FROM GARAGE DOOR OPENER 1. Press and hold the learn button on garage door opener until the learn LED goes out {approximately 6 seconds). 2.
To Open the Door Manually DISCONNECT THE TROLLEY Trolls 1. The door should be fully closed if possible. Tray 2. Pull down on the emergency release fleas srr handle so the trolley release arm Oo Mani) snaps to the vertical position. The position) door can now be raised and lowered as offend as necessary. TO RE-CONNECT THE TROLLEY Logout position 1. Pull the emergency release handle {Manual disconnect) toward the garage door opener so Toh the trolley release arm snaps to the horizontal position.
TROUBLESHOOTING DIAGNOSTIC CHART Your garage door opener is programmed with self-diagnostic capabilities. The UP and DOWN arrows on the garage door opener flash the diagnostic codes. UP ARROW ~~ DOWN ARROW SYMPTOM SOLUTION FLASHES) FLASHES) 1 1 The garage door opener will not Safety sensors are not installed, connected, or wires may be close and the light bulbs flash. cut.
TROUBLESHOOTING UP ARROW DOWN ARROW SYMPTOM SOLUTION FLASHES) FLASHES) 4 5 Opener runs approximately 6-8" Communication error to travel module. Check travel module {15-20 om), stops and reverses. connections, replace travel module if necessary. 4 6 The garage door opener will not Safety sensors are misaligned or were momentarily close and the light bulbs flash. obstructed. Realign both sensors to ensure both LED are steady and not flickering.
REPAIR PARTS 041A7920-2 11474765 Rail Assembly Parks KEY PART NO. NO. DESCRIPTION 1 4A1008 Master link kit 2 41051412 Complete trolley assembly 3 41A5865 Complete rail 4 4184103 Spring trolley nut 5 144054 Play kit 8 41AB250 Full belt assembly 7 1205081 “U” bracket NOT SHOWN 183A163 Wear pads KEY PRAY NO. HNO. DESCRIPTION 1 41A7563 Smart Control Panel® 2 138.20498 3-Button remote control 3 10A20 3Y CR2032 Lithium battery 4 208137 Visor clip 5 139.
Motor Unit Assembly Parts KEY PART KEY PRAY NO. NO. DESCRIPTION NG. HO.
ACCESSORIES 139.53702 Emergency Key Release: 139.30498 Remote Control: Required for a garage with NO access door. 2 Works with all Craftsman openers 1983rd Enables homeowner to open garage door Present. includes visor clip. & manually from outside by disengaging trolley. 139.53728 8 Foot (2.4 m} Rail Extension: © Tallow an 8 foot (2.4 m) door to open fully. Wireless Keypad: For use outside of the home to enable access to the garage using a 4-digit PIN.