2905A56 owner's manual _/___/__ / CRAFTSMAN WET SHARP MACHINE CAT. NO. 146,669950 CAUTION: Read Safe and Rules for Operation Instructions Carefully • Introduction • Operation Sold by SEARS, 2905A56 ROEBUCK AND CO., Chicago, IL 60684 US.A.
FULL ONE YEAR WARRANTY ON CRAFTSMAN WET If this Craftsman Wet Sharp Machine fails to give complete purchase, RETURN IT TO THE NEAREST SEARS STORE Sears will repair it, free of charge. If the Wet Sharp Machine is used for commercial from the date of purchase. This warranty to state. SEARS, gives you specific ROEBUCK legal AND CO. rights, DEPT.
RULES FOR SAFE OPERA TION (Continued) 12. DON'T ABUSE ceptacle. Keep 13. SECURE and CORD. Never carry tool by cord or yank cord from heat, oil and sharp edges. WORK. it frees Use clamps both hands 14. DON'T 15. MAINTAIN OVERREACH. TOOLS and safest sories. performance. or avise to operate Keep WITH proper CARE. and tools instructions for DISCONNECT REMOVE that keys 18. AVOID ACClDENTALSTARTING. Be sure switch is off when plugging Don't in. 19. NEVER ATMOSPHERE.
FEATURES AND ADJUSTMENTS HOUSING STC SCISSOR ON/OFF GUIDE _WER CORD GRINDING WHEEL HOUSING SCREWS ADJUSTABLE TOOL REST WATER RESE FELT BOTTOM HOUSING WIPER SCISSOR BLADE RELIEF ANGLE SELECTOR GUIDE tOOL RETAINING REST KNOB Fig. 1 LEG This unique design of the Wet Sharp Machine incorporates the features most desired in a wet grinding and sharpening machine. HOLLOW GROUND Fig. EDGE: A sharp tool makes any cutting job easier.
i FILLING THE m COOLING . , SYSTEM: Loosen tool rest knobs and allow tool rest to hang down as shown in Fig. 4. Remove wiper as shown in Fig. 3, and soak with water. Replace wiper. Take some water in a container and pour it "SLOWLY," directly on the wheel with a back and forth motion as shown in Fig. 4. IT IS IMPORTANT TO SOAK THE WHEEL: continue pouring water on the wheel until water level in the reservoir is about 3/4 full. Reservoir capacity is approximately 1/2 oz. Do not overfill. See Fig. 5.
1/16" CLEARANCE GENERAL ,...jL..,__(__ • • ..,,.,.,,,.. SHARPENING Refer to Fig.8. Make sure machine is turned "OFF" while making adjustments. Loosen both tool rest knobs (1). Slide tool rest (2) along the slot (3) until tip of angle selector arrow (4) is just touching the dot (5) of the angle selector guide for the desired angle. ,.,, Be sure you maintain 1/16" clearance between grinding wheel (6) and tool rest (2) for safety. IMPORTANT! ALWAYS TIGHTEN RIGHT KNOB FIRST TO MAINTAIN RECT SETTING.
HINTS 1. Check: While in "OFF" proper sharpening angle. 2. Practice: structions. While still position, in "OFF" use the "visual position check" practice procedure procedures as described as described on page 6 for in the following in- 3. Deburr: After you are finished sharpening there may be a fine burr on the cutting edge. This may be removed by drawing the blade across the HONE STONE at approximately the same angle it was sharpened at. Hone both sides of the blade.
If blade is curved at the end, rotate knife handle toward you when approaching knife's tip as shown in Fig. 14. Sharpen the other side of the blade the same way as described above except hold knife as shown in Fig. 15 & 16. Deburr as described . on page 7. Fig. 1 4 PULL TO LEFT Fig. 1 5 SHARPENING Fig. 1 6 TOOLS Micro-Bevel--some tools such as chisels and plane blades require what Is called a "micro-bevel" edge to improve tool performance and cutting edge strength.
Fig. 20 You will only need to grind in both angles if cutting edge becomes badly damaged. (Fig. 20) BADLY DAMAGED CUTTING EDGE REQUIRING BOTH PRIMARY AND SECONDARY ANGLES TO BE GROUND. Move the tool back and forth across If this occurs "Care "dress" of Grinding the wheel grinding as described wheel to avoid wearing in the maintenance down the wheel section unevenly. of this manual under Wheels." MAINTENANCE CARE OF WIPER Clean wiper after each use to remove grinding residue or "swarf.
NOTES lo
EXPLODED VIEW PARTS LIST Model NO. DESCRIPTION PART NO. 1 Screw 2 Housing 3 Switch 4 Bearing - Intermediate 5 Washer (2) 6 Intermediate (8) 953A17-1 - Top 2905E2 2905A12 Cap (2) 2901A14 500A18 Gear & Shaft 2905A9 Ass'y 96A63 7 Spring 8 Grommet (4) 2901A52 9 Spherical Bearing 2901A36 10 Washer Grinding Wheel Shaft 11 Filter 12 Right Tool 2905B8 2905A15 (Wiper) Rest Left Tool 2905A37 Ass'y Rest Bracket 14 & Ass'y Bracket 13 146.
owner's _/AVR8 manual _q°'__/PJR_ / CR RFT$ M RN OWNER'S MANUAL WET SHARP MACHINE SERVICE MODEL NO. Now that you have purchased your Wet Sharp Machine should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co. stores. Be sure to provide all pertinent facts when you call or visit. 146. 669950 The model number of your Wet be found on the plate attached Sharp Machine will to the top housing.
