owners manual MODELNO. 149.236321 SERIAL OR CODE NUMBER: Model and code number may found on the back of the base. be You should record both model and code number and retain in a safe place for future use. SEA IRS / r.RRFT$ MRN_._ CALIFORNIA OWNERS: a unique serial code number is stamped on the underside of the machine, 5%-INCH JOINTER-PLANER CAUTION: Read All Instructions Carefully Before Starting Assembly and Use. • assembly • operating Save This Manual For Future Reference.
FULL ONE-YEAR WARRANTY ON I:RFIFTSMRNoJOINTER If within one year from the date of purchase, this Craftsman Jointer in material or workmanship, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE CENTER IN THE UNITED STATES. This warranty gives you specific state to state. Sears, Roebuck BY CONTACTING -- PLANER -- Planer falls due to a defect THE NEAREST SEARS STORE OR SERVICE legal rights and you may also have other rights which vary from and Co., Dept.
7.KEEP CHILDREN AWAY Atlvisitors should bekeptasafedistance fromworkarea. 8.MAKE WORKSHOP KIDPROOF withpadlocks, master switches, orbyremoving starter keys. 9.DON'T FORCE TOOL It willdothejobbetterandbesaferattherateforwhichit wasdesigned. 10.USERIGHTTOOL Don'tforcetoolorattachment todoajobforwhichitwasnot designed. 11.WEAR PROPER APPAREL Nolooseclothing,gloves,neckties, rings,bracelets, or jewelrytogetcaughtinmoving parts.Nonslip footwear is recommended. Wearprotective haircovering tocontain long hair. 12.
UNPACKING Model 149.236321 carton. Jointer-Planer is shipped AND CHECKING complete in one TABLE OF LOOSE PARTS LU. tm_ z. LL, Separate all parts from packing materials and check each one with the illustration and the list of loose parts to make certain all items material.
SAFETY RULES FOR JOINTER--PLANER Safety is a combination of operator common sense and alertness at all times when the Jointer--Pianer used. Study these rules and general safety rules before operating and retain them for future use. 1. WEAR EYE PROTECTION. 2. NEVER MAKE JOINTING 1/8 INCH -- PER PASS. OR PLANING CUT DEEPER 9. ALWAYS narrower inches. THAN - Use hold downlpush blocks for jointing material than 3 inches, or planing material thinner than 3 10. ALWAYS 3. FEED WORKPIECE 4.
FENCE LOCK NOTE; LESS MAY 1. 1.
A= 11/16 Thickx2"Widex 10"Long The11/16 thickness canbeobtained byplaning theboard onthejointer-planer. B= 112"to3t4"Thickx 3-112" Wide x 10" Long This piece ,.C= ' may also OPTIONAL -- For Extra Stability D= 11116" Thick x 2" Wide x 2" Long, 2 Pieces E= be made out of plywood. 3/4" Thick x 2.112" Wide x 19-1/2" Long The 2-112" width may be increased if desired. __/ C 112" to 314" Thick x 3-1/2" Wide x 2" + Long, 2 Pcs.
INSTALLING If the Jointer-Planer should be fastened THE JOINTER--PLANER _- 3/8 is to be used in a permanent location, it securely to a firm supporting surface such DIA as a workbench. Holes should be drilled through supporting surface of the workbench as illustrated. Each foot of the JointerPlaner should be bolted securely using 5/16" diameter machine bolts, 5116" hex nuts, and lock washers.
TO CHECK DEPTH OUTFEED TABLE OF CUT a. Place a straight table. edge on the outfeed table extending b. Measure from the surface of the infeed table straight edge. This will be the depth of cut. over the infeed to the bottom MAX. DEPTH .OF CUT 1/8" of the NOTE: This Jointer-Planer will make a maximum 118" deep cut. To reduce THE DANGER of kickback and possible injury, the depth of cut should not exceed 1/16" when cutting wood wider than 1.1t2".
BASIC JOINTER--PLANER OPERATION For your safety do not exceed a 1t16" deep cut on a planing operation for work pieces wider than 1-112'". For work pieces less than 1.1/2", a 118" cut can be taken at a slow feed rate. For your own safety, ALWAYS use hold downlpush blocks when JOINTING wood that is NARROWER than 3 in. or when PLANING WOOD THAT IS THINNER than 3 in. This Jointer-Planer is designed with a special cutter head and internal baffle that blows the sawdust and chips from the rear of the machine.
WARNING: NEVER PLACE THE HEEL OF YOUR HAND AT THE END OF THE WORK PIECE WHEN FINISHING A CUT. THIS COULD RESULT IN YOUR HAND COMING IN CONTACT WITH THE CUTTER CAUSING SERIOUS INJURY, _ At the end of the cut, position your hand on TOP NEAR THE END of the work piece and continue feeding the work piece until the cutter guard has returned to its closed position, RIGHT / USING HOLD DOWN/PUSH ALWAYS use the hold downlpush blocks that is NARROWER than 3 in. or PLANING than 3 in.
Forbevelingandchamfering operations, followthe same procedure asforjointing andplaning described onpages 10and 11.Before performing these operations make surethesurface of theworkpiecethatcontacts thefenceisflatandsmooth, Main. lainfirmcontroloftheworkpieceatalttimesholding it firmly against fence surface andtablesurfaces. Useholddowntpush blocksforwoodunder3in.wide.Position themsoyouhavecontrol oftheworkpieceatalltimesandso theydonotcontact theguard orthecullerhead.
BLADE REPLACEMENT AND ADJUSTMENT NOTE: To rotate the cutterhead or to hold it steady, use a screwdriver in the slot in the cutter shaft through the small hole the rear of the machine just above the vacuum port. BLADE 2. Block the cutter 3. Using WOOD BLOCK CUTTER HEAD 1. Unplug your Jointer-Ptaner and put switch in off position. DANGER: Failure to unplug your Jointer-Planer could result in accidental starting causing serious injury. CLAMP SCREW guard open.
CRAFTSMAN 5-1/8 INCH JOINTER-PLANER MODEL No. 149.236321 m 46 FOR Read YOUR OWN SAFETY and Understand instruction operating 47 76 manual before tool • Wear eye p_olection • Newer guards operate io_nt er wilh cutter or dd_e guards remoVeL_ • Never exceed oper,li_on a 118 _ deep cut • Aiway,s use hold-downfpuP*h lot joh_t_ng m_er_a_ n_rrowe_ 3 _n, or 3 _n. , " planing material head m an,/ 62 b_ocks than thinner 63 _64 _han 49 77 61 6O 69-_ 53 21 71 ._ \ 41 , 2 \ 40
CRAFTSMAN 5-1/8 INCH JOINTL._-PLANER MODEL No. 149.236321 PARTS LIST REF. NO. PART NO. DESCRIPTION QTY. REF. NO. PART NO.
TROUBLE SHOOTING TROUBLE CHART REMEDY PROBABLECAUSE Woodstrikes outfeed table after passing over cutterhead Ripples on planed surface, Planed surface not straight. t. Bladesimproperly adjusted below surfaceof outfeed table, 1. Re-adjust blades, 2. Infeed table out of adjustmenl 2. Contact your nearest Searsstore or service center. 1. Oneblade set higher than other, 1. Re-adjust blades 2. Dult blades. 2. Re-sharpen or replace, 3, Board not held firmly against fence or outfeed table 3.