's m 8} 1-1/2 Horsepower (continuous duty) 2.1 Horsepower (maximum developed) 1200 C.FoM° 3450 R.PoM. (no _oad R.PoM.) ST COLL Model No. 152.213371 c_uS CAUTION: FOR YOUR OWN SAFETY; Read and follow all of the Safety and Operating Instructions before Operating this Dust CoUlector. Customer Helpline 1-800-897-7709 PRease have your Model No. and SedaR No. avaHabUe. Sears, Roebuck Part No. 0R93765 and Co., Hoffman Estates, JL 60179 U.S.A. Espa_olpg.
SECTmON PAGE Warranty ..................................................................................... 2 Product 2 Specifications Safety mnstructions Grounding Specific ......................................................................... ............................................................................ mnstructions .........................................................................
GENERAL SAFETY iNSTRUCTiONS Operating a Dust Collector can be dangerous if safety and common sense are ignored, The operator must be familiar with the operation of the took Read this manual to understand this Dust Collector, DO NOT operate this Dust Collector if you do not fully understand the limitations of this tool, DO NOT modify this Dust Collector in any way, REMEMBER: Your personal safety is your responsibility, BEFORE READ the entire Owner's Manual, LEARN how to use the tool for its intended app
21, EACHANDEVERYTmME,CHECK FOR DAMAGED PARTS PRmOR TO USmNGTHE TOOL, Carefully check all guards to see that they operate properly, are not damaged, and perform their intended functions, Check for alignment, binding or breaMng of moving parts, A guard or other part that is damaged should be immediately repaired or replaced, 22, CHILDPROOF THE WORKSHOP AREA by removing switch keys, unplugging tools from the electrical receptacles, and using padlocks, 23, DO NOT OPERATE TOOL IF UNDER THE INFLUENCE OF DRUGS O
Fig. GROUNDED OUTLET BOX-- THIS TOOL MUST BE GROUNDED WHILE iN USE TO PROTECT THE OPERATOR FROM ELECTRIC SHOCK.
SPECiFiC SAFETY iNSTRUCTiONS FOR DUST COLLECTORS The operation of any Dust Colbctor can result in debris being thrown into your eyes, which can result in severe eye damage, ALWAYS Wear Safety Goggbs (that comply with ANSi standard Z87,1) when operating the Dust Collector, Safety Goggbs are availabb at Sears Retail Stores, Keep your thumbs and fingers away from intake ports, Basic precautions should always be followed when using your dust collector, To reduce the risk of injury, electrical shock or fire, com
AVAILABLE ACCESSORIES Visit your Sears Hardware Department or see the Sears Power and Hand Tool CataUog for the following accessories, ITEM STOCK NUMBER 30 micron filter bag (top) 21379 5 micron filter bag (top) 21380 PUastic collection bag (bottom) 21381 4" Diameter x 10' fiexiMe hose 21372 4" Diameter x 25' fiexiMe hose 21373 Various accessory fittings See cataUog or store Sears may recommend other accessories not Hsted in this manual See your nearest Sears Hardware Department or Sears Pow
UNPACKING AN{) CHECKING CONTENTS (Figure 4 and Figure 5) if any parts are missing, do not attempt to plug in the power cord and turn "ON" the Dust Collector, The Dust Collector can only be turned "ON" after all the parts have been obtained and installed correctly, This Dust Collector will require a minimal amount of assembly, Remove all of the parts from the shipping box and lay them on a dean work surface, Compare the items to Figure 4 and Figure 5, verify that all items are account° ed for before discar
Fig.
Fig.
BLOWER AND MOTOR ASSEMBLY TO BASE ASSEMBLY DO NOT assemble the Dust Collector until you are sure the tool IS NOT plugged in, 2, DO NOT assemble the Dust Collector until you are sure the power switch is in the "OFF" position, 2, For your own safety, DO NOT connect the machine to the power source until the machine is completely assembled and you read and understand the entire Owner's Manual, MAKE CERTAIN THE DUST COLLECTOR iS DISCONNECTED FROM THE POWER SOURCE. A CASTER TO BASE B ASSEMBLY Fig.
5, Align the hobs in the drum support with the hobs in the drum (M), Place a 5/16" lock washer on a 5/1618 x 5/8" hex head screw, then 5/16" fiat washer onto the hex head screw, insert the hex head screw thru the hob in drum support and drum, Thread a 5/16" hex nut onto the hex head screw and tighten securely, See figure 11, Fasten the remaining drum supports to the drum in the same manner, Fig.
Fig. 13 1, / / Align the four hobs in intake port (A) with the mounting hobs in flange (B) of blower and motor assembly and fasten with four M4,2 sheet metal screws (C), See figure 14, Fig.
4, Fig. 16 5, \ Place the second locking band through all the loops of the collection bag, similar to the filter bag, Place the collection bag over the lower lip of the drum, Pull up on the retaining clips and insert cop lection bag underneath each retaining clip, Make certain the locking band is positioned in the lower recessed channel of the drum and fasten clamp securely to drum, FLEXIBLE HOSE TO iNTAKE PORT ASSEMBLY D 2, MAKE CERTAIN THE DUST COLLECTOR DISCONNECTED FROM THE POWER SOURCE.
START/STOP FOROPERATOR SAFETY,keepfingersandaHH foreign objectsoutoftheintakeports.Therotatingfaninside theMowerhousingis accessibHe throughthe intake portsandis hazardous. DonotwearHoose cHothing or jeweHry. Makecertainthateachintakeportwhichis not beingusedor attachedto a dustcoHHection systemis coveredwithan intakeportcap. SWITCH Fig. 18 \ CONNECTING TOOL TO POWER SOURCE A separate eHectricaHcircuit shouHd be used for your tooHs.This circuit shouHd not be Hessthan #14 A. W. G.
CHANGING MOTOR VOLTAGE 1, MAKE CERTAIN THE DUST COLLECTOR mS DBCONNECTED FROM THE POWER SOURCE.
HELPFULHINTS: , Alwaysrunthelargestappropriate diameterhose as faras possible,Runninga smallerdiameterhose wiiigreatlyreducetheC,F,M,at thetool,yielding marginaldustcollection, Theuseof a lowratedmicronfilterandcollection bagcanincreasethe effectiveness ofyourdust collectorin removing fineparticlesofdust, Determine if youaretouseyourDustCollectorin a DustCollectionSystemor asa directhook-uptoan individualtookif usedin a DustCollectionSystem, reviewStaticPressureRequirements below, Belowaresometermsthatwiii
C.F.M.REQUIREMENTS FORTOOLS Machine Band Saw (12 to 16qnch) BeWDbc Sander DrHUPress Drum Sander (12 to 24qnch) Fbor Sweep Jointer (up to 8qnch) Jointer (over 8qnch) RadiaU Arm Saw Miter Saw Router TaMe Scroll Saw Minimum 350 450 350 550 350 350 450 450 450 200 200 Spindb Sander TaMe Saw (lOqnch) Thickness Haner (10 to 15qnch) Thickness Planer (16 to 20qnch) STATIC PRESSURE 400 350 400 600 FIEQUJF{EMENTS Using STEPS 1 thru 4 and the "Static for your Dust Collector, Step #1: Pressure C.F._,_.
Topurchaseanyofthe DustCollection Accessories listedbelow,visityournearestSearsStore, VariousFittings: 21340 3=inchHoseCoupling 21363 3=inch90=degree Elbow 21365 3=inchY=Fitting 21367 3=inchT=Fitting 21341 4-inchHoseCoupling 21364 4-inch90-degreeElbow 21366 4-inchYoFitting 21368 4-inchToFitting HOSe: 21370 3-inch x lO-foot Flexible Hose 21371 3-inch x 25-foot Flexible Hose 21372 4-inch x lO-foot Flexible Hose 21373 4-inch x 25-foot Flexible Hose Blast Gates 21359 3-inch Blast Gate - Plastic 213
Turnthepowerswitch"OFF"andunplugthepower cordfromitspowersourcepriortoanymaintenance, Alwaysmakesurethatthe intakeportcapscoversthe intakeportwhena hoseis notconnectedtothedust collector. airmaydamageinsulation.Theoperatorshouldalways weareyeprotectionwhenusingcompressed air. Donotallowchipsanddusttoaccumulate underdust collector.Keepareacleanandin safeorder. CAUTION:DONOTUSEFLAMMABLE MATERIALS tocleanDustCollector.
DUSTCOLLECTOR PARTSUST MODELNO.152.213371 Whenservicing,useonlyCRAFTSMAN replacement parts,Useof anyotherpartsmaycreatea HAZARDor cause productdamage, Anyattemptto repairor replaceelectricalpartsonthisDustCollectormaycreatea HAZARDunlessrepairis doneby a qualifiedservicetechnician, Repairserviceis availableat yournearestSearsServiceCenter, Alwaysorderby PARTNUMBER, notbykeynumber, Key No. PART No. Description Qty. Key No. PARTNo. Description Qty.
ON/OFF S_,'[Sii _RCUN BR C 60 ,,H AKEB_ o O i r"F m !l_i vOLT DONN£U1,Or4 OF 50 850 DUST CO o ECTOR ,,d O 9 "\\ ! ,,d 0_ 2}0 VOLT CONI/EDTION OF 50-850 DUST COLLECTOR f 85 _/ !! 29 28 37 38 27 $9 58 47 4s/! 49 52 _$3 63 _54 _4 0 m 65 "\\ z P N 57 67
NOTES 23
NOTES 24
anuai Propietario 0 1-1/2 cabaHos de fuerza (servicio continuo) 2.1 cabaHos de fuerza (ma×imo desarroHado) 1200 C.F.M. (pies c_bicos pot minuto) 3450 R.PoM. (R.PoM. sin carga) No. de Mode_o 152.213371 c uS PARA SU SEGURIDAD PERSONAL: Lea y obedezca todas Ras tnstrucciones de Seguddad y Funcionamiento antes de accionar este CoUector de PoUvo. I J ,I Linea de Ayuda al Cliente li 1-800-897-7709 I Sirvase tenet listo su No. de Modelo y No. de Serie Sears, Roebuck No. de Pieza OR93765 and Co.
SECCION PAGINA Garant_a ............................................................................................................................................................... 2 Especificacionesde1Producto............................................................................................................................... 2 lnstrucciones de Seguddad ..........................................................................................................................................
INSTRUCCIONES GENERALES DE g. E! funcionamiento de un Colector de Polvo puede resultar peligroso si se hace caso omiso de Ia seguridad y del sentido com0n. El operario debe estar familiarizado con el funcionamiento de Ia herramienta. Lea este manual para entender su Colector de Polvo. NO OPERE este Colector de Polvo si no entiende cabalmente Ias limitaciones de dicha herramienta. NO reaIice modificaciones de cualquier tipo a este Colector de Polvo. RECUERDE; Usted es responsable de su propia seguridad.
21. REVISE SI HAY PIEZAS DANADAS ANTES DE CADA Mientras menor sea eI n0mero de calibre, mayor sera el diAmetro de la extensi6n electrica. Si tiene dudas sobre las USO DE LA HERRAMIENTA. Revise todos los protectores cuidadosamente para comprobar que funcionan correctamente y que no estan daffados, y que realizan sus funciones diseffadas correctamente. Revise el alineamiento, la fijaci6n o la ruptura de Ias piezas en movimiento.
TOMACORRBENTES CONECTADO A TmERRA-- ESTA HERRAMIENTA DEBE ESTAR CONECTADA A TIERRA DURANTE EL USO PARA PROTEGER AL OPERAR_O DE LOS CHOQUES ELECTR_COS.
JNSTRUCCJONES DE SEGURJDAD ESPECJNCAS PARA LOS COLECTORES DE POLVO 12. UTlUCELO s61o como se describe en este manual SOLO utilice los accesofios recomendados per Sears. 13. NO tire de[ colector de polvo mediante el cord6n de energia. JAMAS permita que el cord6n de potencia entre en contacto con bordes filosos, superficies calientes, aceite o grasa.
ACCESOFHOS DJSPONJBLES Sears podra recomendar manual. Visite su Departamento de Ferreteffa de Sears o consulte el Catalogo de Herramientas EI6ctricas y de Mane de Sears para los siguientes accesorios: ARTiCULO otros accesorios no listados en este CensuRe su Departamento de Ferreterfa de Sears mas cercano o el Catalogo de Herramientas Ebetricas y de Mano de Sears para otros accesorios.
DESEMPAQUE Y DEL CONTENJDO (Figura 4 y Figura 5) Si faltan piezas, no intente enchufar el cord6n de potencia y encender e! Colector de Polvo. El Colector de Polvo s6Io podr_i encenderse despues de que se hayan obtenido todas las piezas y estas hayan sido instaladas de manera correcta. El Colector de Polvo requerira una cantidad mfnima de ensamblaje. Quite todas Ias piezas de la caja de env[o y coI6quelas sobre una superficie de trabaio Iimpia. Compare Ios art[culos con Ia Figura 4 y Ia Figura 5.
Fig. 5 K O R H. Banda de cierre I. Bolsa de filtro J. Bolsa de recolecci6n K. Vara de soporte superior * Arandelas de cierre 5/16 putg. (24) h Vara de soporte inferior * Tuercas hexagonales M. Abrazadera de manguera de 6 pulg. (2) * Arandelas planas 5/16 pulg. con diametro externo de 7/8 pulg. (6) N. Manguera flexible con diametro de 6 pulg. * Tornillos de cabeza hexagonal O. Soporte del tambor R Ruedas pivotantes (4) Q. Soporte en U R.
Fig. 6 A A. Bolsa de filtro B. Bolsa de recolecci6n C. Puerto de admisi6n de 4 pulg. D. Tapa del puerto de admisi6n E. Manguera flexible de 6 pulg. F. Base G. Vara de soporte H. Rueda pivotante I.
MONTAJE DEL ENSAMBLADO BEL SOPLADOR Y EL MOTOR A LA BASE 1. NO inicie ei ensamblaje hasta que este seguro de que la herramienta NO ESTA enchufada. 2. NO ensamble eI Colector de Polvo hasta que este seguro de que el interrupter de energfa se encuentre en la posici6n de "APAGADO'. 3. Para su propia seguridad, NO CONECTE Ia m_.quina a la fuente de energfa hasta que la maquina se encuentre completamente ensamblada y usted haya Ie[do y entendido cabalmente el Manuel del Propietario.
5. Alinee los agujeros en el soporte de tambor con los agujeros en el tambor (M). Coloque una arandela de cierre de 5/16 pulg. sobre un tornilIo de cabeza hexagonal de 5/16-18 x 5/8 pulg, y Iuego una arandela plana de 5/16 pulg sobre el tornilIo de cabeza hexagonal. Inserte el tornillo de cabeza hexagonal a traves deI agujero en el soporte deI tambor y el tambor. Enrosque una tuerca hexagonal de 5/16 pulg sobre el tornilIo de cabeza hexagonal y aprietelo de manera segura. Consulte la figura 11.
Fig. 13 1. Alinee Ios cuatro agujeros en eI puerto de admisi6n (A) con los agujeros de montaie en la pesta_a (B) del ensamblado dei sopIador y el motor, y afiancelos con cuatro torniJios de chapa de metal M4.2 (C). Consulte Ja figura 14. Fig. 15 0 0 V 8. Conecte la presilIa de reten de Ia bolsa guardapoivo inferior (V) al tambor coJector de poIvo. AIinee ambos agujeros (W) a la presilIa de reten con los dos agujeros en el tambon Inserte un tornillo de cabeza hexagonal de 1/420 x 5/8 pulg.
4. Fig. 16 5. Co!oque la segunda banda de suieci6n a traves de todos los o]ales de la bolsa de recolecci6n, que es parecida a la bolsa de filtro. Conecte la bolsa de recolecci6n sobre el borde inferior del tambor. Tire las presillas de reten hacia arriba e [nserte Ia bolsa de recolecci6n per debajo de cada presilla de reten. Asegurese de que Ia banda de sujeci6n este colocada en el canal recesado inferior del tambor, y apriete la abrazadera al tambor de manera segura.
JNTERRUPTOR DE ENCENDJDO/APAGADO PARA LA SEGURIDAD DEL OPERARIO, mantenga los dedos y todos los cuerpos extrahos fuera de los puertos de admisi6n. Et acceso al ventilador girante dentro de la caia deI sopJador es posible a traves de Ios puertos de admisi6n y es peligroso. No utilice vestimenta holgada ni artfcuJos de joyerfa. Asegurese de que cada puerto de admisi6n que no este en uso, o conectado a un sistema de recolecci6n de polvo, se encuentre cubierto por una tapa de puerto de admisi6n.
CAMBJANDO DEL MOTOR EL VOLTAJE ASEGURESE DE QUE EL COLECTOR DE POLVO ESTE DESCONECTADO DE LA FUENTE DE ENERGIA. E! motor suministrado con su Colector de Polvo es un motor monofasico de doble voltaje, 120/240 vokios. Se env[a cableado de fabrica para su servicio de 120 voltios. Si elige hacer uso de 240 voltios para accionar su maquina, debe seguir las siguientes instrucciones: Si no esta seguro de las conexiones ni de los c6digos etectricos, comunfquese con un electricista certificado.
A continuaci6n se presentan atgunos t@minos que le ayudaran a entender y montar su Colector de Poivo y a dise_ar su propio sistema de recoIecci6n de polvo. manguera de diametro menor reducir_, considerabiemente el C.RM. en la herramienta, resultando en una recolecci6n de polvo limitada. ¢oBeotor de Polvo - Maquina utiJizada para recolectar poJvo fine y astillas de madera.
REQUJSITOS DE C.FoMoA LAS HERRAMIENTAS _uina C.RM. M{nimo Requerido Sierra de cinta (12 a 16 puig,) Lijadora de correa/disco Taladradora 350 450 350 550 350 350 450 450 450 200 200 400 350 400 600 Lijadora de tambor (12 a 24 putg,) Terraja de piso Machimbradora (hasta 8 pulg,) Machimbradora (mas de 8 pulg,) Sierra de brazo radiat Sierra de ingletes Mesa de recortadora Sierra de calar Lijadora de huso Sierra de mesa (10 pulg,) Cepilladora de grosor (10 a 15 pulg.
Para comprar cualquiera de los Accesorios de Recolecci6n de Polvo listados a continuaci6n, Conectores varios: 21340 AcopIamiento para manguera de 3 puIg. 21363 Pieza acodada de 90 grades de 3 pulg. 21365 Conector en Y de 3 puIg. 21367 Conector en T de 3 puIg. Manguera: 21370 Manguera 21371 Manguera 21372 Manguera 21373 Manguera Flexible Flexible Flexible Flexible de de de de 3 3 4 4 pulg. pulg. pulg. pulg. x x x x 10 25 10 25 visite su tienda Sears mas cercana.
No permita que Ias astiiIas y el polvo se acumulen bajo el coIector de polvo. Mantenga la zona limpia yen seguro estado. Apague el interruptor de energfa y desenchufe el cord6n de potencia de su fuente de energfa antes de realizar cualquier mantenimiento. Asegurese siempre de que Ias tapas de puerto de admisi6n cubran los puertos de admisi6n cuando una manguera no se encuentre conectada al cobctor de polvo. PRECAUC_ON: NO UT_UCE MATER_ALES 8NFLAMABLES para limpiar el cobctor de polvo.
MSTADO DE PIEZAS DEL COLECTOR DE POLVO SCIo utilice piezas de repuesto CRAFTSMAN _,'IODELO NO. 152.213371 durante e! servicio. E! use de cualquier otra pieza podr& crear un PEUGRO o daSo al producto.
E O4/OFF SWITCH CIRCU{] BREAKER ] O m 5 { ON/OFF ',/C_T C:CNNE}IlON SWITCfl CRCU]T QF £085!) DiS7 COLLECTOR m N m BREA14ER O o r m 4 i $ 230 VOL] CONNECTION o o OF 50-850 BUS] COLLECTOR m o o 18 !7 19 37 /38 2O Ob p 3_s 73 59 \ 48 \ / 49 / / 68 / o m o z [ i _ j/55 P / ,j 56 P \\ 67
,_ NOTAS ,_ 47
iiiiiiiiiiiiiiiiii iiiiiiiiiiii iiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiii HHHHHHHHHH For repair -in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories ownersmanualsthatyouneedtodoqt°yourselfi For Sears professional installation and of home appliances and items lime garage door openers and water heaters.