Owner's Manual CRAFTSMAN+ ALL-IN-ONE CUTTING TOOL Model No. 183.172530 Important Safety Notice IA WARNING I Always have one hand firmly placed on the tool body while operating_ Never operate the tool by holding ® only the tool handle. CAUTION: Before using this Cutting Tool, read this manual and follow all its Safety and Operating Instructions. Rules • . Safety Instructions • Accessories • • • • Assembly Operation Maintenance Parts List • Espanol Sears, Roebuck and Co.
SECTION Warranty ........................................ Product Specifications ...................... Power Tool Safety ............................ Cuffing Too_Safety ........................... Electrical Requirements & Safety ........ Accessories .................................... PAGE 2 2 3 4 5 6 SECTION Carton Contents .............................. Know Your Cuffing Too/ .................... Assembty & Operation ...................... Maintenance ...................................
IA WARNING] Before using your cutting tool, it is critical that you read and understand these safety rules. Failure to follow these rules could result in serious injury to you or damage to the cutting tool, Good safety practices are a combination of common sense, staying alert and understanding how to use your power tool. To avoid mistakes that could cause serious injury, do not plug in your cutting tool until you have read and understood the following safety rules: 15. REMOVE ADJUSTING KEYS ANDWRENCHES.
IA WARNING) For your safety, do not plug in your cutting tool or try to use any accessory until it is completely assembled and installed according to these instructions, and until you have read and understood this Owner's Manual. 11. NEVER HOLD THE WORKPIECE IN ONE HAND while operating the tool with the other hand. Failure to follow these safety rules will result in risk of serious Injury. 13. NEVER START THE TOOL WHEN THE BIT IS TOUCHING THE WORKPIECE.
Ie]|J =_lil= II_l-_|l W±lil[o]_ This cutting tool is double insulated to protect you from electrical shock. IA WAJ NING I Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug will fit into a polarized outlet only one way. ffthe plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified eis_dcisn to install a polarized outlet. [3o not alter the plug in any way.
;f-'1£.4I[o]_EaZo]_ III _ _| I_ AVAILABLE ACCESSORIES UNPACKING IA WARNINGI [A Use only accessories recommended for this cutting tool. Follow instructions that accompany accessories. Use of improper accessories may cause injury to the operator or damage to the cutting tool. ff any pert is missing or dameged, do not plug the cutting tool into the power source until the missing or damaged part is replaced end assembly is complete.
Cutting Tool Box Accessory Box I J 7
Rate
IA WARNING] Remove the plug from the power source before assembly, changing accessories or cutters and making adjustments. This safety action will help prevent accidental starting of the tool which could result in serious injury. INSTALLING 4. CUTRNG BITS - Cont'd Insed new cutting bit (4) into the collet.
CHANGING COLLET INSERT INSTALLING Thecutting 1. Slide freehand sole plate mounting bracket (1) onto the bottom of motor housing (2) until the slot in the bracket (3) lines up with the shaft locking button (4) in the motor housing. NOTE: The mounting bracket must be pushed onto the motor housing as far as it will go. 2. Lock the sole plate to the motor housing by snapping the quick locking lever (5) firmly against the motor housing.
PRACTICE CUTS USING FREEHAND SOLE PLATE ,_k WARNING J Have you read "pOWER TOOL SAFETY", "CUI-rING TOOL SAFETY" and "ELECTRICAL SAFETY" on pages 3, 4 and 5 of this Manual? If not, please do it now before you operate this cutting tool. Your safety depends on ttl Every time you use the cutting tool you should verify the following: 1. Cutting tool cord is not damaged. 2. Bit is correct type for the material being cut. 3. Bit is sharp, in good condition, properly installed and securely tightened. 4.
CUTTING OUTLET OPENINGS IN DRYWALL CUTI'ING OUTLET OPENINGS IN DRYWALL - cont'd IAOANGER I Do not attempt to use this tool to make cut-outs around any fixture or opening which has live electrical wires or on any wall which may have electrical wiring behind iL If a live wire is contacted, the bit could conduct the electric current to the tool, creating an electrocution hazard for the operator. Turn OFF breakers or remove fuses to disconnect the electric circuit in the area of work.
i-|:[l_l._][a] _1 -"r:1_isis INSTALLING vtF-'II _/III LIF_,I _[_ I PRECISION HANDLE I,_. DANGER For your own safety, turn the switch OFF and remove the plug from the power source before maintaining your cutting tool. The precision handle is designed for use when precision control over the tool movement is desired. The comfodabie handle can be used with either the dght or left hand. 1. 2. When servicing, use only identical Craftsman ports.
Main Unit 14
IA w ,J.6 I When servicing use only CRAFTSMAN replacement damage to your Cutting Tool. parts. Use of any other parts may create a HAZARD or cause Any attempt to repair or replace electrical parts on this Cutting Tool may create a hazard unless repair is performed by s qualified technician, Repair service is available by contacting your nearest Sears Service Center. Always order by PART NUMBER, not by key number. Main Unit Key # Part # 1 01AR-O00032-0O 2 ! 01AR.
Freehand Soleplate Assembly 212 2O2 2°, 208 215 214 203 216 \ 213 Key# 201 202 203 208 2tl 212 213 214 215 216 part# 02AF-000041-10 02AF-000076-00 02AS-000287-00 2213-MA0010-00 22t3-PA0010-00 2213-PA0011-00 2213-PA0012-00 2213-PA0013-00 2213-PA0014-00 2213-PA0015-00 Part Name Fodngshaft Releaselock pin Screw Freecutmetalround guide Lock F_base plasticguidebase Adjus_nentGear 151" Sleeve Screwlock F 16 oty 1 1 1 1 1 1 1 1 1 1
Handle Assembly ,11301 321 Part# 02AF-000041-10 02AF-000076-00 02AH-000106-00 02AS-000148-00 02AS-000199-A0 02AS-000287-00 02AS-000288-00 02AW-000067-00 2213-MA(X)13-00 2213-PA0010-00 2213-PA0012-00 2213-PA0013-00 2213-PA0014-00 2213-P/_0015-00 2213-PA0016-00 2213-PA0017-00 2213-PA00t8-00 2213-PA0019-00 2213-PA00LT0-00 221_-PA0021-00 Part Name Fixingshaft Releaselock pin Compressivespdng Screw Screw Screw Screw Washer S-roundguideholder Lock Ple._c guidebase Ad.
For repair of major brand appliancesin your own home... no matter who made it, no matter who sold it! 1-800-4-MY-HOME ® Any_me, dayornight (1-300-469-4663) (U.SJ_andCanada) WWW.sears.collt wlNw,sears.cEi For repair of curry-inproductslike vacuums, lawn equipment, and electronics,call for the locationof your nearest Sears Parts and Repair Center. 1-800-488-1222 Any_me, dayorn_ht(U.SAonly) www.sean;.
