Operator’s Manual 10 IN. TABLE SAW WITH LEG SET Model No. 137.218073 C US CAUTION: ● ● ● ● ● Before using this Table Saw, read this manual and follow all its Safety Rules and Operating Instructions Customer Help Line For Technical Support 1-800-843-1682 Safety Instructions Assembly Operation Maintenance Parts List Sears Parts & Repair Center 1-888-331-4569 Sears Brands Management Corporation Hoffman Estates, IL 60179 USA See the full line of Craftsman® products at craftsman.
TABLE OF CONTENTS SECTION PAGE Warranty ................................................................................................................ 2 3 Product Specifications ........................................................................................... Symbols.................................................................................................................. 4 5 Power Tool Safety .................................................................................................
PRODUCT SPECIFICATIONS MOTOR Type............................................................................. Ampere........................................................................ Voltage........................................................................ Hz................................................................................ RPM (no load) ............................................................ Overload Protection....................................................
SYMBOLS WARNING ICONS Your power tool and its Operator’s Manual may contain “WARNING ICONS” (a picture symbol intended to alert you to, and/or instruct you how to avoid, a potentially hazardous condition). Understanding and heeding these symbols will help you operate your tool better and safer. Shown below are some of the symbols you may see. SAFETY ALERT: Precautions that involve your safety. PROHIBITION WEAR EYE PROTECTION: Always wear safety goggles or safety glasses with side shields.
POWER TOOL SAFETY 5. DO NOT USE IN DANGEROUS ENVIRONMENTS. Do not use power tools in damp locations, or expose them to rain or snow. Keep work area well lit. GENERAL SAFETY INSTRUCTIONS BEFORE USING THIS POWER TOOL Safety is a combination of common sense, staying alert and knowing how to use your power tool. ! WARNING 6. KEEP CHILDREN AWAY. All visitors and bystanders should be kept a safe distance from work area.
11. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets or other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair. 12. 13. 14. 16.REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in the OFF position before plugging the tool in. 17.USE RECOMMENDED ACCESSORIES. Consult this Operator’s Manual for recommended accessories.
21.DO NOT OVERREACH. Keep proper footing and balance at all times. NEVER reach across the path of the cutting blade while tool is in operation. 22.MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 23.DO NOT use power tool in presence of flammable liquids or gases. 24.DO NOT operate the tool if you are under the influence of any drugs, alcohol or medication that could affect your ability to use the tool properly.
TABLE SAW SAFETY 1. ALWAYS USE SAW BLADE GUARD, riving knife and antikickback pawls assembly for every through–sawing operation. Through –sawing operations are those in which the blade cuts completely through the workpiece when ripping or crosscutting. Always be sure blade guard is tightened securely. 6. NEVER REACH behind or over the cutting tool for any reason. 7. REMOVE the rip fence when crosscutting. 8. DO NOT USE a molding head with this saw. 9. DIRECTION OF FEED.
14.AVOID AWKWARD OPERATIONS and hand positions where a sudden slip could cause your hand to move into the saw blade. 20.For proper operation follow the instructions in this Instruction Manual entitled ASSEMBLY AND ADJUSTMENTS (Page 20). Failure to provide sawdust fall-through and removal hole will allow sawdust to build up in the motor area resulting in a fire hazard and potential motor damage. 15.NEVER USE SOLVENTS to clean plastic parts. Solvents could possibly dissolve or otherwise damage the material.
TABLE SAW SAFETY glasses, the means to avoid kickback and all other warnings contained in this manual and on the saw itself. Replace the guarding systems as soon as you return to thru-cutting operations. Keep the guard assembly in working order. SAW BLADE GUARD ASSEMBLY, ANTI-KICKBACK ASSEMBLY AND RIVING KNIFE Your table saw is equipped with a blade guard assembly, anti-kickback assembly and riving knife that covers the blade and reduces the possibility of accidental blade contact.
d. e. f. g. h. i. j. k. l. m. n. once it has started. Check their action before ripping by pushing the wood under the anti-kickback assembly. The teeth must prevent the wood from being pulled toward the front of the saw. Plastic and composite (like hardboard) materials may be cut on your saw. However, since these are usually quite hard and slippery, the anti-kickback pawls may not stop a kickback. Therefore, be especially attentive to following proper set up and cutting procedures for ripping.
ELECTRICAL REQUIREMENTS AND SAFETY IMPROPER CONNECTION of the equipment grounding conductor can result in risk of electric shock. The conductor with the green insulation (with or without yellow stripes) is the equipment grounding conductor. If repair or replacement of the electrical cord or plug is necessary, do not connect the equipment grounding conductor to a live terminal.
overheating and burning out of the motor. The table below shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. The adapter (Fig. 2) has a grounding lug extending from it that MUST be connected to a permanent earth ground, such as a properly grounded receptacle box. ! CAUTION In all cases, make certain the receptacle is properly grounded.
TOOLS NEEDED FOR ASSEMBLY ACCESSORIES AND ATTACHMENTS SUPPLIED RECOMMENDED ACCESSORIES ! WARNING Box-end wrench Visit your Sears Hardware Department or see the Craftsman Power and Hand Tools Catalog to purchase recommended accessories for this power tool. NOT SUPPLIED Flat bladed screwdriver #2 Phillips screwdriver Open-end wrench 2YTV DADO INSERT PLATE ! WARNING To avoid the risk of personal injury: ● Do not use adjustable (wobble) type dadoes or carbide tipped dado blades.
CARTON CONTENTS ! WARNING Separate all parts from packing materials. Check each part with the illustration on the next page and the “Table of Loose Parts” to make certain all items are accounted for, before discarding any packing material. If any part is missing or damaged, do not attempt to assemble the table saw, plug in the power cord, or turn the switch ON until the missing or damaged part is obtained and is installed correctly. Call 1-800-843-1682 for missing or damaged parts.
UNPACKING YOUR TABLE SAW A G F K H O N R P J I M L E D C B S T Q U V W X Y Z 16 AA BB
KNOW YOUR TABLE SAW Miter gauge Left extension table Blade guard Rip fence Blade elevation/ tilting handwheel Overload reset switch Miter gauge and rip fence storage Push stick Locking lever Extension wing locking lever Dust bag ON/OFF switch with safety key Table insert Blade bevel lock knob ON/OFF laser switch Blade Riving knife Anti-kickback pawls assembly Hand hold Rear outfeed support Right extension table Power cord storage Blade storage Wheel Foot pad Blade wrench storage Stand 17
GLOSSARY OF TERMS FREEHAND – Performing a cut without using a rip fence, miter gauge, hold down or other proper device to prevent the workpiece from twisting during the cutting operation. ANTI-KICKBACK PAWLS ASSEMBLY – Prevents the workpiece from being kicked upward or back toward the front of the table saw by the spinning blade. ARBOR – The shaft on which the blade or dado is mounted. GUM – A sticky sap from wood products. BEVEL CUT – An angle cut made through the face of the workpiece.
OVERLOAD RESET SWITCH – Protects the motor if it overloads during operation, provides a way to restart the saw. SAW BLADE PATH – The area of the workpiece or table top directly in line with the travel of the blade or the part of the workpiece that will be cut. PUSH STICK – Used to push workpieces when performing ripping operations. SET – The distance between two saw blade tips, bent outward in opposite directions to each other. The further apart the tips are, the greater the set.
ASSEMBLY ASSEMBLING STAND (FIG. A, B, C) 1. Unpack all parts and group by type and size. Refer to the parts list for correct quantities. 2. Attach four hooks (10) to the top corner of the four legs (2) as shown. The hooks (10) are used to hold the dust bag. NOTE: Make sure the hook (10) is securely fastened to the corner of the leg (2). Fig. B 4 3 6 10 8 1 2 5. Assemble the other upper supports in exactly the same manner. 6.
Fig. E ASSEMBLING THE ROLLER WHEEL TO STAND (FIG. D, E) 1. Place stand upside down on level surface or floor. 2. Place bottom support bracket for roller wheel (18) inner of the front leg (2). 3. Insert the bolt (12) through the roller wheel bracket (11), front leg (2), bottom support bracket (18) and nut (13) as shown. Fully Tighten the nut. 4. Attach the roller wheel (14) to roller wheel bracket (11), bolt (15) and lock nut (16) using square neck bolt (15) and lock nut (16) as shown.
MOUNTING BASE TO STAND USING BOLTS (FIG. H) You can also attach the saw base to the stand using standard bolts. ASSEMBLING TABLE SAW TO STAND USING LOCK LEVER (FIG. G) 1. Attach the locking lever assembly (18) to the top of the leg (2). 2. Lift up the locking lever (19). 3. Thread the two screws (20) into the holes (21) of the locking bracket (24) and stand. NOTE: You may need to loosen the two short support brackets if the two mounting holes are not lined up correctly.
3. Square the saw on the mounting surface and mark the location of the four 3/8 in. mounting holes (1). 4. Drill a 3/8 in. hole into the mounting surface. 5. Mark an 11 in. square (2) centered between the four mounting holes (1). 6. Cut out and remove the square. 7. This opening will allow sawdust to fall through the saw base. 8. Place the saw on the work surface, and align the mounting holes of the saw with those drilled through the surface. 9. Fasten the saw to the work surface. ! 1.
ASSEMBLING THE HANDWHEEL HANDLE (FIG. N) Thread the handwheel handle (1) into the handwheel hole, and then tighten the nut against the handwheel with a 14 mm or adjustable wrench. STORAGE (FIG. K, L, M) Rip fence, miter gauge (Fig. K) Storage brackets for the rip fence (2) and miter gauge (3) are located on the left side of the saw housing. NOTE: Adjust the miter gauge to 45º~60º before putting away in storage. Fig. N Blade Wrench (Fig.
pin in the black plastic stops fits into the matching hole in the support tube. This will “lock” the tube into the support. (Fig. P) 4. Slide the table extension toward the table until it rests against the saw table. 5. Lock both cam locking levers by pushing them in toward the cam locking lever assemblies. 6. If the extension is not level to the table, adjust by inserting the spacers (Carton Contents R) between the extension and the tube it mounts onto. See page 42. 7.
INSTALLING THE BLADE (FIG. R, S, T) ! NOTE: Leave the plastic strip around the saw blade at this time. Remove before using the saw for the first time. Make sure the blade fits flush against the inner flange (6). (Fig. S) Clean the outer blade flange (4) and install it onto the arbor (5) and against the blade (7). (Fig. T) Thread the arbor nut (3) onto the arbor, making sure the flat side of the nut is against the blade, then hand-tighten.
REMOVING THE BLADE (FIG. R, T) 1. Remove the table insert. 2. Raise the blade to the maximum height position by turning the blade elevation/tilting handwheel (1) clockwise. (Fig. U) 3. Loosen the blade bevel lock knob (2). Turn and move the handwheel (1) to 45° on the bevel scale. 4. Tighten the blade bevel lock knob (2). ! WARNING To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is not connected to the power source outlet. 1.
! BLADE GUARD ASSEMBLY (FIG. X, Y, Z, AA) WARNING ● To avoid the lock lever (8) interfering with the table insert, after tightening the riving knife, position the lock lever pointing downward before using saw. Failure to maintain a level insert can result in serious injury to the operator. ● The lever can be pulled out to allow it to be turned to a new position downward. (Fig. W) Fig.
Fig. Z Fig. X 2 Loosen 4 5 5 Press down 3 1 Fig. Y 8 1 2 Tighten 6 7 Fig. AA 5 4. Take the blade guard (4) and press down on the red spring button (5) located on the top of assembly. (Fig. Z) 5. Position blade guard over the riving knife (1) and align the slot (6) to the riving knife (1) as shown in Fig. Z. 6. Lower the guard assembly (4) onto riving knife (1). Release the red spring button (5) so that two latches (7) engage into two locking hooks (8) completely. (Fig. Z, AA) 7.
INSTALLING THE BATTERIES FOR THE LASER GUIDE (FIG. CC) 2. Loosen the blade bevel lock knob and turn the handwheel to 90° on the bevel scale. 3. Tighten the blade bevel lock knob. 4. Remove the anti-kickback pawls assembly by lifting the locking lever (2). (Fig. X) 5. Remove the blade guard assembly by pressing down the red spring button (5) and lifting up the assembly. (Fig. AA) ! Failure to unplug your saw could result in accidental starting causing possible serious personal injury. 1.
INSTALLING THE RIP FENCE (FIG. DD) 1. Lift upward on the rip fence handle (1) so the rear holding clamp (2) is fully extended. 2. Place the rip fence on the saw table, and attach the set plate (3) under the fence handle (1) to the rail first. 3. Push down on the fence handle (1) to lock. Fig. DD 1 3 2 ! WARNING Never use a rip fence and miter gauge together.
ADJUSTMENTS MOVE THE TABLE SAW (FIG. EE) 1. Slide the table extension toward the table until it rests against the saw table and tighten the two cam locking levers. 2. Hold the table saw firmly, pull the table saw toward you until the saw is balanced on the wheels. 3. Move the saw to the desired location for operation or store the saw in a dry environment. 4. If adjustment is needed to make the fence parallel to the groove, do the following: ● Loosen the two bolts (3) and lift up on the handle (2).
RIP FENCE INDICATOR ADJUSTMENT (FIG. GG) 1. The rip fence indicator (1) points to the measurement scale. The scale shows the distance from the side of the fence to nearest side of the blade. 2. Measure the actual distance with a rule. If there is a difference between the measurement and the indicator, adjust the indicator (1). 3. Loosen the screw (2) and slide the indicator to the correct measurement on the scale. Tighten the screw and remeasure with the rule. 2.
Fig. II 7. Check again to see if the blade is 90° to the table. If not, repeat step 5. 8. Lastly, check the bevel angle scale. If the pointer does not read 90°, loosen the screw holding the pointer and move the pointer so it is accurate at 0° and retighten the pointer screw. 2 2 1 Fig. JJ 90º ADJUSTING THE 90° AND 45° POSITIVE STOPS (FIG. JJ, KK) Your saw has positive stops that will quickly position the saw blade at 90° and 45° to the table. Make adjustments only if necessary. 45º 1 2 45° Stop 1.
Fig. KK ! 3 To prevent personal injury: ● Always disconnect plug from the power source when making any adjustments. ● Inaccurate adjustment can result in kickback and serious personal injury. This adjustment must be correct or accurate cuts cannot be made. 4 BLADE TILT POINTER (FIG. LL) 1. When the blade is positioned at 90°, adjust the blade tilt pointer (1) to read 0° on the scale. 2. Loosen the holding screw (2), position the pointer over 0° and tighten the screw.
If the blade is partial to left side: 1. Turn the right adjustment screw (2) counterclockwise and adjust the left side adjustment screw (1) clockwise. 2. Remeasure, as described in steps 4 to 9 in the prior section. 3. When alignment is achieved, turn the right adjustment screw (2) until it touches the pivot rod (3). 9. If the ruler touches the marked tooth at the front and rear position, no adjustment is needed at this time.
NOTE: ● This table saw is provided with a 10 inch diameter blade with a body thickness of 0.07 in. thick with a kerf of 0.10 in. The riving knife is 0.09 in. thick. The blade diameter and the blade body and kerf dimensions must be properly matched with the riving knife thickness. ● The maximum radial distance between the riving knife and the toothed rim of the saw blade is 0.12 in ~ 0.31 in. ● The tip of the riving knife shall not be lower than 0.04 in. ~ 0.2 in. from the tooth peak.
! ● CAUTION - Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. ● CAUTION - The use of optical instruments with this product will increase eye hazard. ● Do not attempt to repair or disassemble the laser. If unqualified persons attempt to repair this laser product, serious injury may result. Any repair required on this laser product should be performed by authorized service center personnel.
Fig. PP 4. Use the 5 mm hex wrench that is not provided, adjust the laser unit (2) until the laser line is parallel with the blade. NOTE: Be careful not to overrotate the laser unit. Do not rotate the laser more than 1/8 of a turn in either direction. 5. Adjust the set screws (1) on the left or right side in order to shift the laser line until it is flush with the right side of the blade.
ADJUSTING THE REAR OUTFEED SUPPORT (FIG. RR) 1. The rear outfeed support (1) should be positioned as close as possible to the rear of the table when ripping short material. 2. The rear outfeed support (1) should be fully extended when ripping longer materials that require extra support. Fig. RR 1 ADJUSTING CAM LOCKING LEVER (FIG. SS) If the extension table moves when it is open and locked, then the cam locking lever (1) may be loose and need adjustment.
OPERATION 1. To turn the saw ON, insert the safety switch key (1) into the slot in the switch (2). Move the switch upward to the ON position. 2. To turn the saw OFF, move the switch downward. 3. To lock the switch in the OFF position, grasp the end (or yellow part) of the safety switch key (1), and pull it out. 4. With the safety removal key removed, the switch will not operate. 5.
! Fig. WW WARNING To avoid injury, the ON / OFF switch should be in the OFF position and the plug removed from the power source while the cool down takes place, to prevent accidental starting when the reset button is pushed. Overheating may be caused by misaligned parts or a dull blade or undersized extensing cord. Inspect your saw for proper setup before using it again. 3 4 CUTTING OPERATIONS There are two basic types of cuts: ripping and crosscutting.
RIPPING (FIG. XX, YY) ! To make an additional push stick, use the pattern on page 56. (Fig. ZZ) WARNING To prevent serious injury: ● Never use a miter gauge when ripping. ● Never use more than one rip fence during a single cut. ● Do not allow familiarity or frequent use of your table saw to cause careless mistakes. Remember that even a careless fraction of a second is enough to cause a severe injury. ● Keep both hands away from the blade and clear from the path of the blade.
FEATHERBOARD (FIG. ZZ, aa) A featherboard is a device used to help control the workpiece by guiding it securely against the table or fence. Featherboards are especially useful when ripping small workpieces and for completing non-through cuts. The end is angled with a number of short kerfs to give a friction hold on the workpiece and locked in place on the table with C-clamps. Test that it can resist kickback. 9. Never pull the piece back when the blade is turning. Turn the switch Off.
USE A FEATHERBOARD (FIG. aa) 1. Lower the saw blade (1). 2. Position the rip fence (2) to the desired position and lock the rip fence. 3. Place the workpiece (3) against the fence and over the saw blade area. 4. Adjust the featherboard (4) to resist the workpiece forward of the blade. 5. Attached the C-clamps (5) to secure the featherboard to the edge of the table. 1 3 Make sure the screw heads do not stick out from the bottom of the base; they must be flush or recessed.
● Keep both hands away from the blade and the path of the blade. ● Never attempt to pull the workpiece backwards during a cutting operation. This will cause kickback and serious injury to the user can occur. Making the bracket: ● Start with 3/8 in. wood at least 3/8 in. wide or wider and 2-1/2 in. long or longer. ● Cut the piece to shape and size as shown. Putting it together: ● Fasten the base and handle together with glue and woodscrews. ! 1.
Fig. dd ! WARNING Always work to the right side of the blade during this type of cut. The miter gauge must be in the right side groove because the bevel angle may cause the blade guard to interfere with the cut if used on the left side groove. 1 2 USING THE WOOD FACING ON THE MITER GAUGE (FIG. ee) Slots are provided in the miter gauge for attaching an auxiliary facing (1) to make it easier to cut very long or short pieces.
! Fig. hh WARNING 1 Always work to the right side of the blade during this type of cut. The miter gauge must be in the right side groove because the bevel angle may cause the blade guard to interfere with the cut if used on the left side groove. 3 2 1. Set the miter gauge (1) to the desired angle. 2. Place the miter gauge in the right side groove of the table. 3. Set the blade (2) bevel to the desired bevel angle. 4.
NON-THROUGH CUT (FIG. jj) A non-through cut is used to cut grooves and rabbets in the workpiece without exposed the blade. ! Fig. jj Non-through Cut WARNING ● Only this type cut is made without installing the blade guard assembly and anti-kickback pawls assembly. ● To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is disconnected from the power source outlet. ● To avoid the risk of personal injury.
2. Install the dado table insert making sure that the rear of the insert is flush with the table. If the dado insert is not flush with the table, adjust the two bolts on the insert with a 4 mm hex wrench until it is parallel with the table. 3. Instruction for operating the dado is packed with the separately purchased dado set (not included with unit). 4. The arbor (1) on this saw restricts the maximum width of the cut to 1/2 in. (Fig. kk) 5.
MAINTENANCE BLADE RAISING AND TILTING MECHANISM (FIG. mm, nn) After every five hours of operation, the blade raising mechanism and tilting mechanism should be checked for looseness, binding, or any other abnormalities. 1. With the saw disconnected from the power source, turn the saw upside down and pull up and push down on the motor unit. 2. Observe any movement of the motor mounting mechanism. 3. Loosen or tighten the four hex screws (1) by hex wrench for smooth operation. Adjust only 1/8 turn at a time.
Fig. nn The carbon brushes included with the unit will last approximately 50 hours of running time, or 10,000 ON/OFF cycles. Replace both carbon brushes when either has less than 1/4 in. length of carbon remaining, or if the spring or wire is damaged or burned. 2 3 1. Remove the blade guard, blade, rip fence, miter gauge and stand assembly from the table saw. 2. Lower the blade height to its minimum setting. This will make the brush locations easier to access. 3.
7. Carefully remove the spring-loaded cap, and then pull out the brush (4) and replace. (Fig. pp) 8. Repeat step 6 and 7 for the other side of motor. 9. Place the new brush into the opening of motor, making sure the ears on the metal end of the assembly go in the same hole the carbon part fits into. Do not overtighten the plastic cap. 10.Carefully set the saw in a upright position on a clean level surface. 11. Replace the blade guard, blade, rip fence, miter gauge and stand assembly to the table saw.
TROUBLESHOOTING GUIDE ! WARNING To avoid injury from accidental starting, always turn switch OFF and unplug the tool before moving, replacing the blade or making adjustments. PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION Saw will not start. 1. Saw is not plugged in. 2. Fuse blown or circuit breaker tripped. 3. Cord is damaged. 4. Debris in on/off switch 1. Plug in saw. 2. Replace fuse or reset circuit breaker. 3. Replace power cord. 4. Remove switch from saw and separate in half.
! WARNING To avoid injury from accidental starting, always turn switch OFF and unplug the tool before moving, replacing the blade or making adjustments. PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION Material kicked 1. Rip fence out of adjustment. 1. back from blade. 2. Riving knife not aligned with 2. blade. 3. 3. Feeding stock without rip 4. fence. 4. Riving knife not in place. 5. 5. Dull blade. 6. 6. The operator letting go of material before it is past saw blade. 7. Miter angle lock knob is not 7.
PUSH STICK CONSTRUCTION ● Use good quality plywood or solid wood ● Use 1/2 in. or 3/4 in. material ● Push stick MUST be thinner than the width of material being cut 0m m) Drill Hole For Hanging 15 -3/ 4i n. (40 Notch To Prevent Hand From Slipping Cut Here To Push 1/2 in. Wood Cut Here To Push 3/4 in.
PARTS LIST 10 IN. TABLE SAW WITH LEG SET ! MODEL NO. 137.218073 WARNING When servicing use only CRAFTSMAN replacement parts. Use of any other parts many create a HAZARD or cause product damage. Any attempt to repair or replace electrical parts on this Table Saw may create a HAZARD unless repair is done by a qualified service technician. Repair service is available at your nearest Sears Service Center. PARTS LIST FOR TABLE SAW (A) I.D.
10 IN. TABLE SAW WITH LEG SET PARTS LIST FOR TABLE SAW (B) I.D. 25AP 26E8 26LU 275F 275R 27JR 28N2 290M 29Z5 2A47 2A48 2BUY 2DUB 2ESS 2FSV 2FTB 2GYV 2JHQ 2NE3 2NE4 2NRD 2NRE 2NRF 2NRG 2NSC 2RV8 2RVH 2RVJ 2RVK 2RVM 2RVP 2RVR 2RVW 2RW3 2RW4 2RW6 2RWA 2RWG 2SE0 2SE9 2SJU 2SUS 2SV1 2SV2 2T6E 2TD0 Description HEX. SOC. HD. CAP BOLT FLAT WASHER WARNING LABEL LOCATION SEAT LOCATION SEAT HEX. SOC. SET SCREW BATTERY CAUTION LABEL BLADE ASS’Y HEX. HD. SCREW AND WASHER HEX. HD. SCREW AND WASHER BODY SHELL CR. RE.
10 IN. TABLE SAW WITH LEG SET SCHEMATIC MODEL NO. 137.
10 IN. TABLE SAW WITH LEG SET PARTS LIST FOR MOTOR MODEL NO. 137.218073 I.D. Description 0HX9 NEEDLE BEARING Size Q’ty 0JX3 HEX. SOC. SET SCREW M5*0.8-8 2 0KCP CR. RE. PAN HEAD TAPPING & WASHER SCREW M5*12-60 2 0KTK STRAIN RELIEF 0QM2 BRUSH HOLDER ASS’Y 0QQT BRUSH ASS’Y 2 0QR0 BRUSH COVER 2 2DW9 WAVE WASHER 1 2RPP FLOW GUIDE 2RPS MOTOR COVER 2RRD CUTTER SHAFT ASS’Y 1 2RT8 ARMATURE ASS’Y 1 2RWF BRACKET 2RWS CR. RE. COUNTER-SUNK HEAD SCREW 2RXC LABEL 3235 CR. RE.
10 IN. TABLE SAW WITH LEG SET PARTS LIST FOR STAND MODEL NO. 137.218073 I.D. Description Size 0J4F FLAT WASHER φ8*16-2.5 4 2SB2 PLUNGER HOUSING 0JPS HEX. HD. BOLT M8*1.25-45 4 2SB3 CLAMP HANDLE CG# 1 0KHX CAP HD. SQ. NECK BOLT M5*0.8-10 2 2SBX HANDLE KR# 1 0KJ7 CAP HD. SQ. NECK BOLT Q’ty I.D. Description Size Q’ty 1 M8*1.25-16 1 2SE1 ROLLING WHEEL 1 0KQW LOCK NUT M5*0.8 T=5 2 2SE2 DUST BAG 1 0KQY LOCK NUT M8*1.
REPAIR PROTECTION AGREEMENTS Congratulations on making a smart purchase. Your new Craftsman® product is designed and manufactured for years of dependable operation. But like all products, it may require repair from time to time. That’s when having a Repair Protection Agreement can save your money and aggravation.
