Operator’s Manual 6.0 Horse Power YARD VACUUM Model No. 247.770550 CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. • Safety • ESAssembly • Operation • Maintenance • Parts • Español Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A. Visit our Sears website: www.sears.com/craftsman Printed in U.S.A. FORM NO. 769-00407.
TABLE OF CONTENTS Content Page Content Page Warranty 2 Service and Adjustments 14 Safety 3 Storage 16 Assembly 5 Troubleshooting 17 Operation 7 Parts List 18 Maintenance 12 WARRANTY Limited Warranty on Craftsman Yard Vacuum For one (1) year from the date of purchase, if this Craftsman Equipment is maintained, lubricated, and tuned up according to the instructions to the operator’s manual, Sears will repair or replace free of charge any parts found to be defective in material or workman
SAFETY WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol - heed its warning.
i. Never store the machine or fuel container inside where there is an open flame, spark, or pilot light (e.g. furnace, water heater, space heater, clothes dryer, etc.) j. To reduce a fire hazard, keep machine free of grass, leaves, or other debris build-up. Clean up oil fuel spillage and remove any fuel soaked debris. k. Allow machine to cool at least 5 minutes before storing. 9. Never operate without either the inlet nozzle or optional hose attachment properly attached to the machine.
ASSEMBLY NOTE: Reference to right and left hand side of the Yard Vacuum is observed from the operating position. See Figure 1. This Yard Vacuum has been completely assembled at the factory, except for the handle, bag, and blower chute. These parts are shipped loose in the carton. A pair of safety glasses and a 20-oz. bottle of engine oil are also included in the carton. See Figure 1. 20-oz.
• • • • Secure the two handles by tightening the upper wing nuts (carriage bolts must be seated properly into the handle). Remove the hairpin clips from the handle brackets and remove the carriage bolts and wing nuts from the lower handle. See Figure 3. Place the bottom holes in lower handle over the pins on handle brackets and secure with hairpin clips. Insert carriage bolts through upper hole in lower handle from the outside and secure with wing nuts.
• Raise the nozzle height to the highest setting when using the blower chute. Refer to nozzle height adjustment in the ADJUSTMENT section. NOTE: The bag/chute switch button attached to the mounting bracket must be fully depressed by the tip of front tab on the blower chute or engine will not start.
OPERATION Know Your Yard Vacuum Read this operator’s manual and safety rules before operating your Yard Vacuum. Compare the illustrations below with your equipment to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. The operation of any Yard Vacuum can result in foreign objects being thrown into the eyes, WEAR YOUR SAFETY GLASSES which can result in severe eye damage.
Hose Assembly • Used as an alternative to the nozzle to vacuum yard waste such as leaves or pine needles in hard to reach places. Hose Handle Used to guide hose assembly when vacuuming. • Nozzle/Hose Vac Handle The nozzle/hose vac handle is located on top of the nozzle and it is used to regulate the vacuum between the nozzle and the hose assembly. Fill fuel tank with clean, fresh, unleaded regular, unleaded premium or reformulated automotive gasoline only. DO NOT use Ethyl or high octane gasoline.
When temperature is below 32 degrees F: • Move throttle control / choke lever on engine to CHOKE position. (A warm engine may not require choking.) See Figure 8. • If not using choke to start engine, move throttle control / choke lever to START/RUN position. • Depress the primer bulb firmly with your thumb three times. Wait about two seconds between each push. Buttons Inner Flap Bag Clip Bag Handle NOTE: See air cleaner on side of engine for further starting instructions.
Nozzle Height Adjustment Nozzle/Hose Vac Handle (Top Position) The nozzle can be adjusted to any six positions, ranging from 5/8” to 4 1/8” ground clearance. The nozzle height has to be adjusted according to the conditions. Move the height adjustment levers forward or backward to adjust the nozzle upwards or downwards. See Figure 12. NOTE: In general, raise the nozzle height to vacuum a thick layer of leaves or to operate with the blower chute and lower the nozzle height for smoother surfaces.
PRODUCT MAINTENANCE SCHEDULE Be for ee ac hu se Af te r ea ch us e Fir st 5h ou rs Ev er y2 5h ou rs Ev er y5 0h ou rs Be fo r es to r ag e MAINTENANCE Lubrication Clean equipment ENGINE Check engine oil Change engine oil Service air cleaner Service spark plug Service muffler Clean engine GENERAL RECOMMENDATIONS CLEAN EQUIPMENT • • • • • • Always observe safety rules when performing any maintenance.
TO DRAIN OIL SERVICE SPARK PLUG Drain oil while engine is warm. Follow the instructions given below. • • • • • • Drain the gas tank, start the engine and let it run until the fuel line and carburetor are empty. Remove oil fill dipstick. Tip unit on its side to drain through the oil fill tube. When engine is drained of all oil, refill with approximately 20 oz. of fresh oil. Refer to Gas And Oil Fill-up in OPERATION section. Replace dipstick. Clean the spark plug and reset the gap to .
SERVICE AND ADJUSTMENTS WARNING: Do not at any time make any adjustment to the unit without first stopping engine and disconnecting spark plug wire. WARNING: Do not attempt to alter the engine speed by tampering with the engine’s governor linkage. Doing so could result in serious personal injury and damage to the engine. The engine RPM has been set at the factory. Nozzle Height Adjustment The nozzle can be adjusted to any six positions, ranging from 5/8” to 4 1/8” ground clearance.
SHARPENING OR REPLACING CHIPPER BLADE • Because the engine on this unit has a tapered crankshaft, a special impeller removal tool (part number 753-0900) is required to remove the impeller assembly. For further assistance, contact your Sears Service Center. • NOTE: When tipping the unit, empty the fuel tank and keep engine spark plug side up. Chipper Blade • • • Remove lock nut that secures flail screen to the lower housing. The flail screen does not have to be removed. Refer to Figure 15.
STORAGE NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Prepare your Craftsman Yard Vacuum for storage at the end of the season or if the unit will not be used for 30 days or longer. A yearly check-up by your local Sears Service Center is a good way to ensure that the unit runs properly next season. • Add stabilizer to gasoline in fuel tank or storage container. • Always follow the mix ratio found on stabilizer container.
TROUBLESHOOTING Problem Possible Cause(s) Corrective Action Engine fails to start 1. Fuel tank empty or stale fuel. 1. Fill tank with clean, fresh gasoline. Fuel will not last over thirty days unless a fuel stabilizer is added. 2. Connect wire to spark plug. 3. Obstruction lodged in impeller. Disconnect spark plug wire and remove lodged object. 4. Move CHOKE to ON position. 5. Clean, adjust gap or replace. 6. Safety switch must be depressed by the front tab on the bag handle when securing the bag. 7.
PARTS LIST Sears Craftsman 6.0 H.P. Yard Vacuum Model 247.
Sears Craftsman 6.0 H.P. Yard Vacuum Model 247.770550 Ref. No. 1. 2. 3. 4. 5. 6. 7. 8. 9. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. Part No. 720-0295 749-1423 720-0279 712-3004A 710-1205 781-1056 710-0528 720-0314 710-1174 710-0604A 681-0174 749-0907B 711-1293 710-0703 712-0397 751B282454 725-1700 725-3166 731-1613 710-0224 629-0920 714-0104 736-0264 732-0962 781-0778A 747-1153 710-3195 710-3025 Ref. No.
Sears Craftsman 6.0 H.P. Yard Vacuum Model 247.
Sears Craftsman 6.0 H.P. Yard Vacuum Model 247.770550 Ref. No. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. Part No. 664-0094 681-0154 710-1054 781-0490 681-0152 781-0735 719-0329 715-0166 711-1401 736-0247 736-0217 710-0818 710-3038 781-0721A 712-3004A 712-3027 736-0142 714-0225 711-1560 731-2294 781-1064 732-1156 726-0106 711-1551 712-0161 736-0400 731-2485 710-1156 750-1294 732-3118 732-1151 Ref. No.
12H800 1019 LABEL KIT 1 2 1058 OWNER’S MANUAL 3 584 718 684 11 585 50 847 54 523 51 306 842 287 7 307 13 525 869 870 871 5 14 6 8 374 9 524 337 46A 46 635 383 10 25 27 40 43 45 36 374 868 16 40 33 45 35 24 34 26 28 715 1095 VALVE GASKET SET 9 721 27 146 7 29 101 741 32A 743 357 32 357A 883 358 ENGINE GASKET KIT 83 4 4A 20 3 20A 7 12 12 51 163 524 9 585 15A 617 12 668 842 883 15 15 20 20 20A 1102 22 Illustrations cover a range of engines
12H800 125 97 134 365 633 163 133 104 130A 975 137 127 98 130 95 617 94 276 118 276 117 276 PRIMER SYSTEM 125A 692 109 109A 217 633A 633 134 97 365 163 133 633 108 217 104 127 975 137 130A 127A 98 130 95 617 94 276 118A 276 117A 276 CHOKE SYSTEM 121 CARBURETOR OVERHAUL KIT 94 134 276 617 104 137 127 127A 633 977 CARBURETOR GASKET SET 137 633A 163 163 276 633 633A 617 Illustrations cover a range of engines.
12H800 968 425A 425 968B 966A 967A 425 159 445A 443A 970 968A 976 529 163 967 445 966 976 443 11A 259 163 300 300A 300B 883 81 81 81 613A 613 613B 836A 832 832A 832B 836 836 836B 832C 832D 836 836 994 836 994A 836B 346 676 676A 677 677 676B 676C 677 677 676D 677 676E 677 Illustrations cover a range of engines. Parts shown without corresponding text may not be used on your specific engine. 0990–4 Assemblies include all parts shown in frames.
12H800 972 972A 957 957 930 1040 972D 1059 930C 957A 190 670 957 972B 972C 957 957A 187 187A 187B 187C 601 601 601 601A 601 240 958 209 209A 209B 843A 843 222 601A 188 222A 222B 222C 621 621 621 227 562 98A 668 668 668 222D 222E 668 505 222F 202 615 410 404 624 624A 489 668 668 616 668 268 267 271 270 269 267 265 265A 267A 265B Illustrations cover a range of engines. Parts shown without corresponding text may not be used on your specific engine.
12H800 564A 986 604 604A 969A 564 921 921C 930 921A 969 969A 930A 921D 930C 563 949 997 921B 703 921E 921F 37 78 304A 304 305 925 1229 1036 EMISSION LABEL Illustrations cover a range of engines. Parts shown without corresponding text may not be used on your specific engine. 0990–6 Assemblies include all parts shown in frames.
12H800 608 608A 65 55A 55 65 455 592 592 455A 58 144 1211 678 60A 59 60 776 73 57 946 1210 58 946 60B 459A 459 689 456 59A 597 276A 456A 689A 1134 101A 332 455 73 73A 363 23 23A Illustrations cover a range of engines. Parts shown without corresponding text may not be used on your specific engine. 0990–7 Assemblies include all parts shown in frames.
12H800 333 356 892 500 664 334 356A 851 356B 1119 356C 474 990 259 356D 990A 940 910 356E 627 356F 507 520 347 359 578 373 497 789 789A 1160 789B 745 236 923 309 510 935 922 621 742 923A 937 922A 783 784 1208 651 942 785 513 783A 801 545 1236 544 1009 697 803 853 310 802 Illustrations cover a range of engines. Parts shown without corresponding text may not be used on your specific engine. 0990–8 Assemblies include all parts shown in frames.
12H800 REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION REF. NO. 2678, 2679, 3120, 3123, 3167, 3176. 493282 Crankshaft (Used Before Code Date 97011300). Used on Type No(s). 0823, 1520, 1530, 1531, 1532, 1533, 1567, 2630, 2631. 1 2 493260 Cylinder Assembly 399269 Kit–Bushing/Seal (Magneto Side) 3 K299819 Seal–Oil (Magneto Side) 4 493279 Sump–Engine ––––––– Note ––––– 498983 Sump–Engine Used on Type No(s). 1167, 1715, 1955, 2320, 2324, 2331, 2367, 2673, 2681, 3182.
12H800 REF. NO. 20 20A 22 23 23A 24 PART NO. DESCRIPTION K399781 Seal–Oil (PTO Side) K691952 Seal–Oil (PTO Side) (Auxilliary PTO) 691092 Screw (Crankcase Cover/ Sump) 692315 Flywheel (Rewind Start) 691987 Flywheel (Electric Start) ––––––– Note ––––– 691992 Flywheel (Electric Start) Used on Type No(s). 0667, 1149, 1167, 1369, 1548, 1559, 1569, 1714, 1715, 1919, 1932, 1941, 1942, 1955, 2320, 2324, 2331, 2349, 2367, 2383, 2391, 2635, 2669, 2673, 2681, 3133, 3178, 3179, 3183.
12H800 REF. NO. 28 29 32 32A 33 34 35 36 37 40 PART NO. DESCRIPTION 499423 Pin–Piston (Standard) (Used After Code Date 97011200). ––––––– Note ––––– 298909 Pin–Piston (Standard) (Used Before Code Date 97011300). 298908 Pin–Piston (.005” Oversize) (Used Before Code Date 97011300). 499424 Rod–Connecting (Standard) (Used After Code Date 97011200). ––––––– Note ––––– 490566 Rod– Connecting (Standard) (Used Before Code Date 97011300). 490743 Rod– Connecting (.
12H800 REF. NO. 117 117A 118 118A 121 PART NO. DESCRIPTION 494870 Jet–Main (Standard) ––––––– Note ––––– 497466 Jet–Main (Standard) Used on Type No(s). 1538. 498977 Jet–Main (Standard) Used on Type No(s). 0664, 0665, 0666, 0667, 0671, 0672, 1149, 1167, 1170, 1368, 1369, 1370, 1373, 1548. 498978 Jet–Main (Standard) 497315 Jet–Main (High Altitude) 496495 Jet–Main (High Altitude) Used on Type No(s). 1538. 498978 Jet–Main (High Altitude) Used on Type No(s).
12H800 REF. NO. 209 209A PART NO. DESCRIPTION 691864 Spring–Governor (Light Blue) Used on Type No(s). 2329, 2349. ––––––– Note ––––– 690242 Spring– Governor (Orange) Used on Type No(s). 1932. 690241 Spring– Governor Used on Type No(s). 3183. 690567 Spring–Governor (Platinum) Used on Type No(s). 1167. ––––––– Note ––––– 690568 Spring– Governor (Navajo White) Used on Type No(s). 1149, 1548. 691835 Spring– Governor (Meadow Green, 365 Load) Used on Type No(s).
12H800 REF. NO. 217 222 222A 222B 222C 222D 222E 227 236 240 259 265 267 268 269 270 271 PART NO. DESCRIPTION 690354 Spring–Choke Return 692031 Bracket–Control (Remote/Manual Friction)(Primer) 692021 Bracket–Control (Remote, Choke A Matic, Non Compliance) ––––––– Note ––––– 690839 Bracket– Control (Manual Friction) (Choke A Matic) Used on Type No(s). 1149, 1167, 1548.
12H800 REF. NO. 445A 455 456 459 474 497 500 505 507 510 513 520 523 524 525 529 544 545 562 564 564A 584 585 592 597 PART NO.
12H800 REF. NO. 801 802 803 832 832A 832B 836 836A 836B 842 843 843A 847 851 853 869 PART NO. DESCRIPTION 690782 Cap–Drive 695267 Cap–End (Used After Code Date 00040600). ––––––– Note ––––– 695975 Cap–End (Used Before Code Date 00040700). 695266 Housing–Starter (Used After Code Date 00040600). ––––––– Note ––––– 695975 Housing– Starter (Used Before Code Date 00040700).
12H800 REF. NO. 970 972B 975 976 977 986 990 990A 994 1009 PART NO. DESCRIPTION 691669 Screw (Air Cleaner Primer Bracket) 495224 Tank–Fuel (Plastic) ––––––– Note ––––– 499618 Tank–Fuel (Plastic) Used on Type No(s). 1720, 2384. 695960 Tank–Fuel (Plastic) Used on Type No(s). 1717, 1718, 1719, 1754, 2326, 3181. 493640 Bowl–Float 694395 Primer–Carburetor (Used After Code Date 99051200). ––––––– Note ––––– 496115 Primer– Carburetor (Used Before Code Date 99051300).
CONTENIDO Contenido Página Contenido Página Garantía 38 Servicio y ajustes 50 Seguridad 39 Almacenamiento 52 Montaje 41 Localización de averías 53 Operación 44 Lista de repuestos 18 Mantenimiento 48 GARANTIA Garantía de un año sobre la aspiradora para jardines Craftsman Por un período de un año a partir de la fecha de compra, Sears reparará gratis cualquier defecto en el material o fabricación de esta aspiradora para jardines Craftsman, siempre y cuando haya sido mantenida, lubricada y
SEGURIDAD ADVERTENCIA: Este símbolo indica instrucciones de seguridad muy importantes las que, si no se siguen, podrían poner en peligro la seguridad personal y/o causar daños físicos. Antes de intentar manejar esta aspiradora para jardines, se debe leer y seguir todas las instrucciones que aparecen en este manual. Si no se cumplen estas instrucciones se corre el riesgo de sufrir lesiones. Cuando en el manual aparece este símbolo, respetar su advertencia.
• • • • • • • • SERVICIO piedras, pedazos de vidrio o de metal) y sean lanzados por la boca de descarga. Al elevar la boquilla a la posición más alta también incrementa la admisión de aire para lograr mejor funcionamiento del soplador. No intentar nunca retirar o vaciar el recolector mientras el motor está funcionando. Apagar el motor y esperar hasta que el rotor esté detenido antes de retirar el recolector (bolsa). El rotor continúa girando por algunos segundos después de apagar el motor.
MONTAJE NOTE: Para determinar los lados derecho e izquierdo de la aspiradora para jardines, situarse detrás de la máquina, en posición de manejarla. Ver la figura 1. Botella de 20 oz. aceite para motor La aspiradora para jardines fue armada en la fábrica, con la excepción del manillar, recolector y tubo de soplado. Estos componentes se envían sueltos en la caja de cartón. En la caja también se incluyen anteojos de seguridad y una botella de 20 onzas de aceite para motor. Ver la figura 1.
• • Retirar las chavetas de las escuadras del manillar y los tornillos de carruaje (cabeza de hongo y cuello cuadrado) y tuercas de mariposa del manillar inferior. Ver la figura 3. Colocar el manillar inferior sobre los pasadores en las escuadras y fijarlos con las chavetas, tornillos de carruaje y tuercas de mariposa.
• • • Asir el tubo de soplado con una mano y, con la otra mano, tirar de la varilla de fijación en la escuadra de montaje hacia el motor. Use el final de soporte de montaje como el apalancamiento deslizando la barra que se cierra. Ver la Figura 6. Deslizar el tubo de soplado por encima del borde de la boca de descarga y soltar la varilla de fijación para sujetar el tubo en su lugar. Cuando se va a usar el tubo de soplado, elevar la boquilla a la posición más alta.
OPERACION Conozca su aspiradora para jardines Lea este manual del operador y las reglas de seguridad antes de manejar su aspiradora para jardines. Compare las ilustraciones presentadas más abajo con su equipo para que conozca bien la ubicación de los distintos controles y ajustes. Guarde este manual para consultarlo en el futuro. USE SUS El manejo de cualquier aspiradora para jardines sopladora puede causar el lanzamiento de ANTEOJOS DE objetos extraños contra los ojos y lesionarlos gravemente.
Montaje de la manguera Se usa como alternativa del uso del pico para aspirar los desechos que se acumulan en los patios como por ejemplo las hojas o las agujas de los pinos que se encuentran en lugares de difícil acceso. • Manija de la manguera Se utiliza para guiar el montaje de la manguera mientras se aspira.
arranque accidental mientras la máquina está sola. 6. Estando parado detrás de la unidad, agarre la manija del arrancador y saque la cuerda hasta que usted siente una fricción. ADVERTENCIA: Al mover la palanca de mando de válvula reguladora, tenga cuidado de superficies calentadas y de bordes sostenidos del silenciador guarde. 7. Tire de la cuerda con un movimiento rápido, continuo, completo del brazo. Guarde un apretón firme en la manija del arrancador. Deje la cuerda rebobinar lentamente. 8.
• • • IMPORTANTE: La pantalla de desgranado está ubicada dentro de la caja en la zona de descarga. Si se tapa la pantalla de desgranado, sáquela y límpiela como se indica en SECCIÓN 5: MANTENIMIENTO DE LA ASPIRADORA PARA PATIOS. Para obtener el mejor resultado es importante también mantener afilada la hoja de la cortadora. Comprima la abertura de la bolsa y doble la aleta interior sobre la abertura.
PRODUCTO PROGRAMA DE MANTENIMIENTO An te al m s d ac el en am De ien sp to c a ué da s d us e o Pr im er as 5h or Ca as da 25 ho ra s Ca da 50 ho ra s An tes na d m i el en alm to a ce - MANTENIMIENTO Lubricación Limpiar el equipo Revisar nivel aceite MOTOR Campiar aceite motor Limpiar filtro de aire Limpiar la bujía Limpiar el silenciador Limpiar el motor RECOMENDACIONES GENERALES LIMPIEZA DEL EQUIPO • • • • • • Siempre respetar las reglas de seguridad durante los trabajos de mantenimiento.
PARA VACIAR EL ACEITE SERVICIO DE LA BUJIA Vaciar el aceite mientras el motor está caliente. Seguir las instrucciones siguientes. • • • • • • Vaciar el tanque de gasolina, arrancar el motor y dejarlo funcionando hasta que la tubería de combustible y el carburador estén vacíos. Retirar la varilla de medición de llenado de aceite. Inclinar la máquina sobre su costado para vaciar el aceite por el tubo de llenado.
SERVICIO Y AJUSTES máquina a un centro de servicio Sears para reparación y ajuste. ADVERTENCIA: Nunca hacer ningún ajuste a la máquina sin primero apagar el motor y desconectar el cable de la bujía. WARNING: No intentar alterar la velocidad del motor moviendo el varillaje del gobernador del motor. El hacerlo podría resultar en graves lesiones personales y daño al motor. La velocidad (rpm) del motor fue ajustada en la fábrica.
• • Retirar el tornillo hexagonal y la arandela plana ubicados encima de la carcasa trasera cerca de la escuadra de montaje y la contratuerca que sujeta la rejilla de flagelos. Ver las Figura 14. Retirar y limpiar la rejilla con una rasqueta o lavarla con agua. Volver a instalar la rejilla. Caja Tornillos AFILADO O REEMPLAZO DE LA CUCHILLA ASTILLADORA Debido a que el motor de esta máquina tiene el cigüeñal cónico, se necesita un extractor especial (número de pieza 753-0900) para retirar el impulsor.
• Apretar los tornillos de la cuchilla a 210 - 250 pulg-lbs. • Apretar el perno del rotor a 375-425 pulg-lbs. NOTE: Asegurar de instalar la cuchilla astilladora con el filo hacia arriba. Ver la Figura 19. Cuchilla astilladora Cuchilla de flagelos Rotor Figura 19 ALMACENAMIENTO Preparar la aspiradora para jardines Crafstman para su almacenamiento al final de la temporada o si la máquina va a estar sin usar durante 30 días o más.
LOCALIZACION DE AVERIAS Problema Causas posibles Solución El motor no arranca 1. El tanque de combustible está vacío o combustible está viejo. 1. Llenar el tanque con gasolina limpia y fresca. El combustible no durará más de treinta días a menos que se le añada un estabilizador. 2. Conectar el cable de la bujía. 2. El cable de la bujía está desconectado. 3. No se puede tirar de la cuerda de arranque. 4. El estrangulador está en la posición ON (conectado). 5. La bujía está mala. 6.