For Parts Call 606-678-9623 or 606-561-4983 Operator’s Manual ® 6.5 Horse Power LOG SPLITTER Model No. 247.77466.1 CAUTION: Before using this product, read this manual and follow all safety rules and operating instructions. • SAFETY • ASSEMBLY • OPERATION • MAINTENANCE • PARTS LIST Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A. Visit our web site: www.sears.com/craftsman www.mymowerparts.com FORM NO.
For Parts Call 606-678-9623 or 606-561-4983 TABLE OF CONTENTS Warranty Statement................................... Page 2 Repair Protection Agreement.................... Page 3 Safe Operation Practices.......................... Pages 4-5 Assembly................................................... Pages 6-7 Operation................................................... Pages 8-11 Service & Adjustments.............................. Pages 12-13 Maintenance..............................................
For Parts Call 606-678-9623 or 606-561-4983 REPAIR PROTECTION AGREEMENT Congratulations on making a smart purchase. Your new Craftsman® product is designed and manufactured for years of dependable operation. But like all products, it may require repair from time to time. That’s when having a Repair Protection Agreement can save you money and aggravation.
For Parts Call 606-678-9623 or 606-561-4983 SAFE OPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol - heed its warning.
For Parts Call 606-678-9623 or 606-561-4983 SAFE OPERATION PRACTICES 15. This machine should not be towed on any street, highway or public road without checking the existing federal, state, or local vehicle requirements. Any licensing or modifications such as taillights, etc., needed to comply, is the sole responsibility of the purchaser. If a “Statement of Origin” is required in your state, see your local dealer. f. Never overfill the fuel tank.
For Parts Call 606-678-9623 or 606-561-4983 ASSEMBLY IMPORTANT: Your log splitter is shipped with motor oil in the engine. However, you MUST check the oil level before operating. Be careful not to overfill. NOTE: All references in this manual to the left or right side of the log splitter is from the operating position only. Removing Unit From Carton 1. Pry the top, sides, and ends off crate. 2. Set panels aside to avoid tire punctures or personal injury. 3. Remove and discard plastic bag that covers unit.
For Parts Call 606-678-9623 or 606-561-4983 ASSEMBLY 2. Disconnect the dislodger from the beam weld bracket by removing the six hex screws. See Figure 3-4. 3. Disconnect the log cradle from the beam on the side of the control valve. See Figure 3-5. 4. Lift and slide the cylinder up to the top of beam and into the weld brackets. 5. Attach the dislodger over the wedge assembly and secure with hardware, previously removed, to the weld brackets.
For Parts Call 606-678-9623 or 606-561-4983 OPERATION Cylinder Control Handle Log Dislodger Wedge Beam Assembly Tongue Jack Stand Vertical Log Cradle Beam Lock Tail Light (If Equipped) Horizontal Beam Lock Vertical Beam Lock Figure 4-1 WARNING: Read this operator’s manual and safety WARNING: Be familiar with all controls and their rules before operating your log splitter. Compare proper operation. Know how to stop the machine the illustrations below with your equipment to and disengage them quickly.
For Parts Call 606-678-9623 or 606-561-4983 OPERATION Engine Controls Stop Switch Push button to ON prior to choking for engine start; push to OFF to shut engine down. Choke Control The choke control is used to choke off the carburetor and assist in starting the engine. To return wedge Starter Handle The starter handle is located on the engine. Pull the starter handle to start engine. Neutral To stop wedge Control Handle The control handle has three positions. See Figure 4-2.
For Parts Call 606-678-9623 or 606-561-4983 OPERATION WARNING: When starting a warm engine, the muffler and surrounding areas are hot and can cause a burn. Do not touch. Using the Log Splitter 1. Place the log splitter on level, dry ground. 2. Place the beam in either the horizontal or vertical position and lock in place with the appropriate locking rod. 3. Block the front and back of both wheels. 4. Place the log against the end plate and only split wood in the direction of the grain. 5.
For Parts Call 606-678-9623 or 606-561-4983 OPERATION Horizontal Position 1. Pull the vertical beam lock out and rotate it down. See Figure 4-1. Pivot beam to the horizontal position. The beam will lock automatically in horizontal position. 2. Stand behind the reservoir tank to operate control handle and to stabilize the log. Operating Tips Always: 1. Use clean fluid and check fluid level regularly. 2. Use an approved hydraulic fluid.
For Parts Call 606-678-9623 or 606-561-4983 SERVICE & ADJUSTMENTS Gib Adjustment Periodically remove and replace the “gibs” (spacers) between the wedge assembly and the back plate. NOTE: The gibs may be rotated and/or turned over for even wear. Adjustment Bolt 1. Loosen the lock nuts under each back plate and slide the gibs out. See Figure 5-1. 2. Turn or replace the gibs. 3. Reassemble the back plate and secure with the lock nuts. 4. Readjust the bolts on the side of the wedge assembly.
For Parts Call 606-678-9623 or 606-561-4983 SERVICE & ADJUSTMENTS 1. Remove three nuts that secure the pump to the coupling shield. Two nuts are at the bottom corners and one is in the top center. See Figure 5-2. 2. Remove the pump. 3. Rotate the engine by slowly pulling starter handle until engine coupling half set screw is visible. Loosen set screw using allen wrench and slide coupling half off engine shaft. 4. Loosen set screw on pump coupling half and remove coupling half. 5.
For Parts Call 606-678-9623 or 606-561-4983 MAINTENANCE Maintenance Schedule TASKS Lubricate Beam & Wedge Before Each Use First 5 Hours Every 25 Hours Every 50 Hours Change Hydraulic Filter Clean Reservoir Screen Check Engine Oil Change Engine Oil Service Air Cleaner Service Spark Plug Clean Engine SERVICE DATES Change Hydraulic Fluid Check Reservoir Fluid Every 100 Hours Figure 5-1 WARNING: Do not at any time make any adjustments without first stopping engine, disc
For Parts Call 606-678-9623 or 606-561-4983 MAINTENANCE Hydraulic Fluid and Inlet Filter • Check the hydraulic fluid level in the log splitter reservoir tank before each use. Maintain fluid level within the range specified on the dipstick at all times. • Change the hydraulic fluid in the reservoir every 100 hours of operation. Follow the steps below: 1. Disconnect the suction hose from the bottom of the reservoir tank. 2. Carefully unthread the inlet filter and clean it with penetrating oil.
For Parts Call 606-678-9623 or 606-561-4983 MAINTENANCE Service cartridge every 25 operating hours or every season. Service cartridge more often under dusty conditions. 2 3 To Service Air Filter 1. Loosen air cleaner cover screw, but do not remove screw from cover. Swing cover down to remove from hinge. 2. Inspect filter for discoloration or dirt accumulation. If either is present, proceed as follows: a. Clean inside of body and cover thoroughly and remove cartridge. b.
For Parts Call 606-678-9623 or 606-561-4983 OFF-SEASON STORAGE Prepare your log splitter for storage at the end of the season or if the log splitter will not be used for 30 days or more. WARNING: Never store machine with fuel in the fuel tank inside of building where fumes may reach an open flame or spark or where ignition sources are present such as hot water and space heaters, furnaces, clothes dyers, stoves, electric motors, etc.
For Parts Call 606-678-9623 or 606-561-4983 TROUBLESHOOTING Problem Engine fails to start Cause 1. Spark plug wire disconnected. 1. Connect wire to spark plug. 2. Fuel tank empty or stale fuel. 2. Fill tank with clean, fresh gasoline. 3. Choke lever not in CHOKE position. 3. Move choke to CHOKE position. 4. Faulty spark plug. 4. Service spark plug following instructions in the maintenance section. 5. Blocked fuel line. 5. Clean fuel line. 6.
For Parts Call 606-678-9623 or 606-561-4983 TROUBLESHOOTING Problem Cause Slow cylinder shaft speed while extending and retracting. 1. Gear sections damaged. 1. Return unit to Sears service center. 2. Excessive pump inlet vacuum. 2. Make certain pump inlet hoses are clear and unblocked. Use short, large diameter inlet hoses. 3. Return unit to Sears service center. 3. Slow engine speed. 4. Damaged relief valve. 5. Incorrect oil level. 7. Directional valve leaking internally. 8.
For Parts Call 606-678-9623 or 606-561-4983 PARTS LIST 6 2 3 75 5 4 1 74 76 8 15 23 19 32 9 11 18 68 63 7 22 12 23 31 24 25 65 41 42 40 41 64 69 13 44 41 67 61 58 57 44 16 20 10 62 56 34 55 65 39 41 71 70 41 44 17 61 33 72 59 43 66 18 59 14 35 A 50 30 27 28 26 37 38 72 29 36 54 46 77 48 47 73 48 51 53 23 23 45 49 52 21 48 A 20 www.mymowerparts.
For Parts Call 606-678-9623 or 606-561-4983 Craftsman 6.5 H.P. Log Splitter Model 247.77466.1 Ref. No. Part No. Description Ref. No. Part No. Description 1. 718-0769A Hydraulic Cylinder 40. 710-0650 TT Screw, 5/16-18 x.875 2. 727-04166 Hydraulic Tube 41. 712-04065 Flange Lock Nut, 3/8-16 3. 710-1018 Hex Cap Screw 1/2-20 x 2.75 42. 781-04129 Log Tray 4. 737-0192 90 Degree Solid Adapter 43. 681-04040 Frame Assembly 5. 718-0481A Control Valve 44.
For Parts Call 606-678-9623 or 606-561-4983 PARTS LIST 101 LABEL KIT 0 1 1 0 1 1 1 0 1 11 10 0 1 0 REPAIR MANUAL 10 OWNER’S MANUAL 1 1 0 A 0 1 1 0 0 22 www.mymowerparts.
For Parts Call 606-678-9623 or 606-561-4983 Sears Craftsman 6.5 H.P. Engine Model No. 123K02 For Log Splitter Model 247.77466.1 1 1 1 0 0 00 1 1 1 1 10 1 A CARBURETOR GASKET SET 1 1 1 1 10 1 A 1 1 1 1 1 1 1 CARBURETOR OVERHAUL KIT 1 10 1 0 11 A 1 10 1 1 0 0 23 www.mymowerparts.
For Parts Call 606-678-9623 or 606-561-4983 PARTS LIST ENGINE GASKET SET 0 1 1 1 1 1 REPLACEMENT ENGINE 0 0 0 100 10 0 1 0 0 1 11 1 10 1 01 10 EMISSIONS LABEL 24 www.mymowerparts.
For Parts Call 606-678-9623 or 606-561-4983 Sears Craftsman 6.5 H.P. Engine Model No. 123K02 For Log Splitter Model 247.77466.1 Ref. No. Part No. Description 1. 697322 Cylinder Assembly 2. 399269 Kit-Bushing/Seal 3. 299819† 4. 5. Ref. No. Part No. Description 58. 697316 Rope-Starter (Cut to Required Length) Seal-Oil (Magneto Side) 60. 281434 Grip-Starter Rope 493279 Sump-Engine 65. 690837 Screw (Rewind Starter) 691160 Head-Cylinder 78.
For Parts Call 606-678-9623 or 606-561-4983 PARTS LIST Ref. No. Part No. Description Ref. No. Part No. Description 347. 691396 Switch-Rocker 684. 690345 Screw (Breather Passage Cover) 356. 693010 Wire-Stop 689. 691855 Spring-Friction 358. 497316 Engine Gasket Set 692. 690579 Spring-Detent 363. 19069 Flywheel Puller 718. 690959 Pin-Locating 365. 692524 Screw (Carburetor) 741. 691830 Gear-Timing 383. 89838 Wrench-Spark Plug 832. 499034 Guard-Muffler 404.
For Parts Call 606-678-9623 or 606-561-4983 LABELS 3 $ 3 ) 7!2.).' 0%23/. 34!"),):).' ,/' /. 30,)44%2 -534 "% 3!-% 0%23/. 7(/ /0%2!4%3 #/.42/, 6!,6% +%%0 (!.$3 !7!9 &2/- 7%$'% !.$ -/6).' 0!243 +%%0 (!.$3 AND &%%4 !7!9 #/.42/, 6!,6% 2%6%23% .%542!, &/27!2$ ,/' $)3,/$'%2 3 !# 2ETRACT WEDGE LODGED WOOD WILL BE AUTOMATICALLY REMOVED 3 6%24)#!, 6ERTICAL 0OSITION ,OCK (/2):/.4!, $!.'%2 /0%2!4/2g3 ).3425#4)/.
For Parts Call 606-678-9623 or 606-561-4983 (This page applicable in the U.S.A. and Canada only.) Sears, Roebuck and Co., U.S.A. (Sears), the California Air Resources Board (CARB) and the United States Environmental Protection Agency (U.S.
For Parts Call 606-678-9623 or 606-561-4983 INDICE Garantía .................................................... Page 29 Protección................................................. Page 30 Ensamble .................................................. Page 32 Funcionamiento ........................................ Page 34 Servicio y ajustes...................................... Page 38 Mantenimiento .......................................... Page 40 Almacenamiento .......................................
For Parts Call 606-678-9623 or 606-561-4983 PROTECCION ADVERTENCIA: Este símbolo indica importantes instrucciones de seguridad la cuales, si no se observan, pueden poner en peligro la seguridad personal y/o la propiedad suya y de terceros. Lea y siga todas las instrucciones en este manual antes de intentar operar esta máquina. El no cumplir con estas instrucciones puede resultar en lesiones personales. Cuando vea este símbolo obedezca a su advertencia.
For Parts Call 606-678-9623 or 606-561-4983 PROTECCION 9. Para evitar lesiones personales o daños a la propiedad se debe ser muy precavido al manejar la gasolina. La gasolina es extremadamente inflamable y los vapores son explosivos.. Pueden ocurrir lesiones personales graves cuando se derrama gasolina sobre el operador o sus ropas ya que puede encenderse. Lavarse la piel y cambiarse de ropas inmediatamente. a. Usar un recipiente aprobado de gasolina solamente. b.
For Parts Call 606-678-9623 or 606-561-4983 ENSAMBLE IMPORTANTE: Esta unidad se envía sin gasolina o aceite en el motor. Antes de operar la máquina, asegurarse de cargar gasolina y aceite según indicado en el manual separado del motor. NOTA: La referencia a la derecha o izquierda de la cortadora de troncos se observa desde la posición de operación. Extracción de la unidad de la caja 1. Separar el tope, lados y extremos del cajón. 2.
For Parts Call 606-678-9623 or 606-561-4983 ENSAMBLE 4. Levantar y correr el cilindro hasta el tope de la viga y dentro de los soportes soldados. Ver la Figura 3-5. 5. Fijar el impulsor sobre el conjunto de la cuña y fijar a los soportes soldados con la ferretería previamente extraída. NOTA: Una vez que los seis tornillos de maleficio son se aprietan, puede haber un hueco leve entre el dislodger y los anaqueles soldarás. Este hueco es aceptable. 6.
For Parts Call 606-678-9623 or 606-561-4983 FUNCIONAMIENTO Manija de control Liberador de la madera Avance Cuña de Corte Bloqueo de la viga horizontal Bloqueo de la viga vertical Bloqueo de la viga horizontal Bloqueo de la viga vertical Figura 4-1 ADVERTENCIA: Lea este manual del operador y las ADVERTENCIA: Familiarícese con todos los conreglas de seguridad antes de poner en funcionatroles y su operación apropiada. Sepa cómo detener miento la máquina cortadora de madera.
For Parts Call 606-678-9623 or 606-561-4983 FUNCIONAMIENTO Controles del motor Interruptor de detención Oprima el botón para ponerlo en ON (encendido) antes del cebado para el arranque del motor, ponga el botón en OFF (apagado) para apagar el motor. Retroceso Control de obturación El control de obturación se utiliza para cebar el carburador y ayudar a que el motor arranque. Neutral Manija del arrancador La manija del arrancador está ubicada sobre el motor.
For Parts Call 606-678-9623 or 606-561-4983 FUNCIONAMIENTO 7. Si falla el motor, coloque la palanca de control en la posición CHOKE (obturación), luego lentamente de nuevo hasta la posición RUN (funcionamiento). 8. Si el clima es frío, mueva la cuña hacia arriba o hacia abajo entre 6 y 8 veces para hacer circular el fluido hidráulico. ADVERTENCIA: Al arrancar un motor caliente, el silenciador y las áreas circundantes están calientes y pueden causar quemaduras. Uso de la cortadora de troncos 1.
For Parts Call 606-678-9623 or 606-561-4983 FUNCIONAMIENTO Posición vertical 1. Colocar la traba horizontal de la viga para soltar la viga y pivotear la viga a la posición vertical. 2. Para trabar la viga en la posición vertical, tirar hacia afuera de la traba vertical de la viga y pivotear para asegurar la viga. Ver la Figura 4-1. 3. Pararse frente a la viga vertical para operar la manija de control y estabilizar el tronco. Ver la Figura 4-3. Posición horizontal 1.
For Parts Call 606-678-9623 or 606-561-4983 SERVICIO Y ADJUSTES Ajuste de la placa de chavetas Extraer y reemplazar periódicamente las chavetas (separadores) entre la placa de la cuña y la placa posterior. NOTA: Las chavetas pueden girarse y/o darse vuelta para un desgaste uniforme. Perno de ajuste 1. Aflojar las contratuercas debajo de cada placa posterior y deslizar hacia afuera las chavetas. Ver la Figura 5-1. 2. Girar o reemplazar las chavetas. 3.
For Parts Call 606-678-9623 or 606-561-4983 SERVICIO Y ADJUSTES IMPORTANTE: No golpear nunca de ninguna manera el eje del motor, ya que un golpe causa un daño permanente al motor. Al reemplazar el acople flexible de la bomba, proceder como sigue: 1. Extraer las tres tuercas y que aseguran la bomba al protector del acople. Dos tuercas están en las esquinas del fondo y una está en el centro del tope. Ver la Figura 5-2. 2. Extraer la bomba. 3.
For Parts Call 606-678-9623 or 606-561-4983 MANTENIMIENTO PROGRAMA DE MANTENIMIENTO TAREAS Lubricar viga y cuña Antes de cada uso Primeras 5 horas Cada 25 horas Cada 50 horas FECHAS DE SERVICIO Cambiar el líquido hidràulico Cambiar el filtro hidràulico Limpiar screen del reservorio Inspeccionar el liquido del reservorio Inspeccionar el aceite del motor Cambiar el aceite del motor Limpiar el filtro de aire Limpiar la bujía Limpiar el motor Cada 100 horas Figura 5-1 A
For Parts Call 606-678-9623 or 606-561-4983 MANTENIMIENTO Líquido hidráulico • Compruebe el nivel hidráulico fluido en el tanque de depósito de hendedor de tronco antes de cada empleo. Mantenga el nivel fluido dentro de la gama especificada sobre la varilla de aceite en cualquier momento. • Cambiar el líquido hidráulico en el reservorio cada 100 horas de operación: 1. Desconectar la manguera de succión del fondo del tanque reservorio y drenar el líquido dentro de un recipiente apropiado. Ver la Figura 5-2.
For Parts Call 606-678-9623 or 606-561-4983 MANTENIMIENTO 2 3 Hágale un servicio al cartucho cada 25 horas de funcionamiento o todas las temporadas. Realice el servicio del cartucho con más frecuencia si está expuesto a mucho polvo. Servicio del filtro de aire 1. Afloje el tornillo de la cubierta del filtro de aire pero no saque dicho tornilla de la cubierta. Gire la cubierta hacia abajo para sacarla de la bisagra. 2. Revise el filtro para detectar la presencia de decoloración o de acumulación de suciedad.
For Parts Call 606-678-9623 or 606-561-4983 ALMACENAMIENTO Al final de la temporada o si la cortadora de troncos no se va a usar por 30 días o más, prepararla para almacenamiento. ADVERTENCIA: Nunca almacenar la máquina con combustible en el tanque de combustible dentro de un edificio donde los humos pueden alcanzar una llama expuesta o chispa o donde estén presentes fuentes de encendido tales como calentadores de agua caliente y espacio, calderas, secadoras de ropa, cocinas, motores eléctricos, etc.
For Parts Call 606-678-9623 or 606-561-4983 GUI DE LOCALIZACION DE FALLAS Problema Causa posible El motor no arranca 1. Filtro de aire sucio. 2. Tanque de combustible vacío, o combustible rancio. 3. El regulador no está en la posición OFF. 4. Tubería de combustible bloqueada. 5. Cable de bujía desconectado. 6. Bujía defectuosa. El motor funciona erráticamente. 1. Unidad funcionando con el regulador. 2. Llenar el tanque con combustible fresco. 3. Mover el regulador a ON. 4.
For Parts Call 606-678-9623 or 606-561-4983 GUI DE LOCALIZACION DE FALLAS Problema Es lenta la velocidad del eje del cilindro mientras se extiende y retrae Causa posible 1. Secciones dañadas del engranaje. 1. Devolver la unidad al Centro de Servicio Sears. 2. Vacío excesivo de entrada a la bomba. 2. Asegurarse que las mangueras de entrada de la bomba estén limpias y desbloqueadas. Usar mangueras de entradas cortas y de gran diámetro. 3. Velocidad lenta del motor. 3.
For Parts Call 606-678-9623 or 606-561-4983 (Esta página se aplica sólo en EE.UU. y Canadá). Sears, Roebuck and Co., U.S.A.
For Parts Call 606-678-9623 or 606-561-4983 ACUERDO DE PROTECCIÓN PARA REPARACIONES Felicitaciones por haber realizado una adquisición inteligente. El producto Craftsman® que ha adquirido está diseñado y fabricado para brindar muchos años de funcionamiento confiable. Pero como todos los productos a veces puede requerir de reparaciones. Es en ese momento cuando el disponer de un Acuerdo de protección para reparaciones le puede ahorrar dinero y problemas.
For Parts Call 606-678-9623 or 606-561-4983 Get it fixed, at your home or ours! Your Home For repair – in your home – of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner’s manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters.