98 .A.uA, I1:RR ........... FTS ........................... MR"N'i ii 3/8 in., 19.2 VOLT RIGHT ANGLE DRILL-DRIVER VARIABLE SPEED/REVERSIBLE Model No. 315.101541 _1_ WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, II. 60179 USA Visit the Craftsman web page: www.sears.
• Warranty ........................................................................................................................................................................... 2 • Introduction 2 • General Safety Rules .................................................................................................................................................... • Specific Safety Rules .........................................................................................................
WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed [] below, may result in electric shock, fire and/or seri= ous personal injury. [] SAVE THESE INSTRUCTIONS [] WORK AREA [] Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents, [] Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
SERVICE • When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of shock or injury. !1 Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury.
_lk could result in a risk of fire and electric shock. If extension cord must be used, make sure: WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions a. That pins on plug of extension cord are the same number, size and shape as those of plug on charger. listed below, may result in electric shock, fire and/or serious personal injury.
Someofthefollowing symbols maybeusedonthistool.Please studythemandlearntheirmeaning. Proper interpretationofthesesymbols willallowyoutooperatethetoolbetterandsafer. NAME SYMBOL • ,, ,,,,,, ,,, DESIGNATIO i V i .i . N/EXPLANATION . | | Volts VoLtage Amperes Current m in. | .,,i. ,H A ill . i,i, i,, Hertz Hz Frequency n u ,.
Thefollowing stgnal wordsandmeanings areintended toexplain thelevelsofriskassociated withthisproduct. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently hazardous result in death or serious injury. _I_ WARNING: Indicates a potentially hazardous situation, which, rf not avoided, could result in death or serious injury. _IL CAUTION: Indicates a potentially hazardous situation, which, if not avoided, result in minor or moderate injury.
PRODUCT SPECIFICATIONS Chuck ...................... "................................... 3/8 in, Keyless Motor .............................................................. 19.2 Volt DC Switch ........................................................ No Load Speed .............................................. Variable Speed Charger Input .................................. 120 V, 60 Hz, AC only Charge Rate ............................................................ Max. Torque ..................
KEYLESS KNOW YOUR DRILL-DRIVER See Figure 1. Before attempting to use this product, familiarize yourself with all operating features and safety rules. BIT STORAGE When not in use, bits provided with the drill-driver placed in the storage area located on the base. can be CHARGER The charger has a key-hole hanging feature for convenient, space-saving storage. Screws should be installed so that the center distance is 4-1/4 in.
A CHARGING WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious tf battery pack is below normal temperature range, the green LED on charger will come on. Allow battery pack to reach normal temperature, then the red LED will come on. injury.
CHARGING A HOT BATTERY PACK CAUTION: When placing the battery pack in the drill, be sure the raised rib on the battery pack aligns with the groove inside the drill and latches snap into place properly, improper assembly of the battery pack can cause damage to internal components. When using the toot continuously, the batteries in the battery pack will become hot, You shou]d let a hot battery pack cool down for approximately 30 minutes before attempting to recharge.
APPLICATIONS You may use this tool for the following To stop the drill, release the switch trigger and allow the chuck to come to a complete stop. purposes: II Drilling in wood • Drilling in ceramics, • Drilling in metals • Mixing paint plastics, fiberglass, NOTE: The drill will not run unless the direction selector is pushed fully to the left or right. and laminates Avoid running the drill at low speeds for extended periods of time.
INSTALLING BITS See Figures 6 - 7. • Lock the switch trigger by placing the direction rotation selector in the center position. • Open or close the chuck opening is slightly larger use. Also, raise the front bit from falling out of the • Insert the drilt bit. • Tighten the chuck jaws on the drill bit. DRILLBIT of jaws to a point where the than the bit size you intend to of the drill sfightly to keep the chuck jaws. UNLOCK (RELEASE) CHUCK COLLAR WRONG REMOVING Fig.
DRILLING m Depress the switch trigger to start the dritl. See Figure 9, III Move the drill bit into the workpiece, applying only enough pressure to keep the bit cutting. Do not force the drill or apply side pressure to elongate a hole. Let the tool do the work. • Check the direction of rotation selector for the correct setting (forward or reverse). ,_ WARNING: Be prepared for binding at bit break- through.
A _1_WARNING: MALLET When servicing, use only identical Craftsman replacement parts, Use of any other part may create a hazard or cause product damage. ,_ WARNING: Always wear safety goggles or safety glasses with side shields when using compressed air to clean tools, tf the operation is dusty, also wear a dust mask. _ WARNING: To avoid serious personal CHUCKJAWS KEYLESS CHUCK injury, always remove the battery pack from the tool when cleaning or performing any maintenance.
TO RETIGHTEN A LOOSE CHUCK BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING The chuck may become loose on the spindle and develop a wobble. Also, the chuck screw may become loose, causing the chuck jaws to bind and prevent them from closing. To tighten: •I Lock the switch trigger by placing the direction of rotation selector in the center position. • Open the chuck jaws. To preserve natural resources, ptease recycle or dispose of batteries property. This product contains nickel-cadmium batteries.
,------ CRAFTSMAN 19.2 VOLT RIGHT ANGLE DRILL-DRIVER- MODEL NUMBER 315.101541 i i,i, ll,lll The model number will be found on a plate attached to the motor housing, Always mention the model [,number in all correspondence regarding your DRILL-DRIVER or when ordering repair parts. SEE BACK i i iJ_-iJl ii PAGE FOR PARTS ORDERING ,,J INSTRUCTIONS ,i, lll 5 i / PARTS LIST Key No. Pad Number Description 1 6612003 Chuck Screw ...........................................................
Get it fixed, at your home or ours! Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME ® (1-800-469-4663) Call anytime,day or night(US.A. and Canada) www.sears.com www.