OWNERS MANUAL MODEL NO. 315.111450 CAUTION: Read Rules for Safe Operation and instructions 3/8 INCH CORDLESS DRILL SINGLE-SPEEDREVERSIBLE Carefully Introduction SAVE THIS MANUAL FUTLIRE REFERENCE SEARS, ROEBUCK _QXj9 Operation FOR Designed exc_usive}y for arid sold only by AND CO, Dept 698/73tA, Sears Tower. Chicago.
FULL ONE YEAR WARRANTY ON CRAFTSMAN CORDLESS DRILL If this Craftsman Cordless Drill falls to give complete satisfaction within one year from the date of put.chase, RETURN IT TO THE NEAREST SEARS STORE THROUGHOUT THE UNITED STATES and Sears wilt replaceit, freeof charge. isused for the dateof purchase.
RULES FOR SAFE OPERATION (CONTINUED) !4,. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see thdt keys and adjusting wrenches are removed from tool before turning it on, 15. NEVER USE IN AN EXPLOSIVE ATMOSPHERE_ Normat sparking of the motor could ignite flammable liquids, gases or fumes, t6 KEEP HANDLES DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning.. Never use brake fluids, gasoline, petroleum_based products, or any strong solvents to clean your tool, 17.
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER 1. SAVE THESE INSTRUCTIONS° This manual contains important safety and operating instructions for battery charger Part Number 999555-007. 2. Before using battery charger, read atl instructions and cautionary markings in this manual, on battery charger, and product using battery charger. 3. __To reduce risk of injury, charge only nickel-cadmium type rechargeable batteries.
OPERATION KNOW YOUR DRILL See Figure 1_ Before attempting to use your drill, familiarize yourself with el! operating features and safety requirements, If any pads are missing do not operate your drill untie the missing parts are replaced. TO CHARGE 1, Connect charger to your drill by inserting charger plug Into input jack, NOTE: As shown In Figure 1, input Jack is located at the rear of toot 2 Charger can be used with normal house voltage of 110.120 volts, 60 Hz. AC only.
OPERATION (Cont.) BATTERIES Your ddtl is equipped with 5 nickel-cadmium rechargeabte batteries Length of service from each charging will depend on the type of work you are doing '[he nickel,.cadmium batteries in this tool have been designed to last for the life of the unit under normal operating conditions.
OPERATION INSTALLING BITS 1 Lock switch trigger on your direction of rotation selector (Cont.) ---- .... ddtt by placing the in center position. 2 Close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use, 3 insert your drilJ bit into chuck the full length of the jaws as shown in Figure 4, 4" Remove chuck key from chuck key storage See Figure 3 5 Tighten chuck jaws by placing chuck key tn each o! the three holes, and tighten in a clockwise direction.
OPERATION (Cont.
MAINTENANCE GENERAL Avoid using solvents when cleaning plastic parts Most plastics are susceptible to various types of oommeP cial solvents and may be damaged by their use, Use clean cloths to remove dirt, dust, oil, grease, etc, ACCESSORIES ...... THE FOLLOWING RECOMMENDED ACCESSORIES ARE CURRENT AND WERE ............. AVAILABLE AT THE TIME THIS MANUAL WAS PRINTED, 5,,Pc, Power Screwdriver Cat, No 9 25602 No, 2 Phillips/8.,10 Cat No 9 25603 Bit Set Slotted.
NOTES Page 10
NOTES Page 11
1" OWNERS MANUAL SERVICE MODEL NO. 315.111450 HOW TO ORDER REPAIR 3/8 INCH CORDLESS DRILL SINGLE-SPEED REVERSIBLE Now that you have purchased your Drill, shoutd a need ever exist for tepai[ parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co, stores Be sure to provide all pertinent facts when you call or visit. The model number of your Drill wiil be found on the plate attached to the motor housing.