Operator's Manual 3/8 in. CORDLESS DRILL-DRIVER Variable Speed / Reversible Model Nos. 315.113320 - 12 Volt 315.113330 - 14.4 Volt Save this manual future reference for • Safety • Features CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Visit the Craftsman web page: www.sears.
• Tablte Of Contents .......................................................................................................................................................... 2 • Warranty ........................................................................................................................................................................ 2 • Introduction ........................................................................................................................
Yourdrill-driverhasmanyfeaturesformakingyourdrilling operations morepleasantandenjoyable. Safety, performance anddependability havebeengiventop priorityinthedesignofthisdrill-drivermakingit easyto maintainandoperate. _L CAUTION:Carefullyreadthroughthisentire operator'smanualbeforeusingyournewdrill-driver. Paycloseattention to theGeneralSafetyRules, SpecificSafetyRules/ Symbols, Warnings and Cautions.
Tool Use and Care • Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. • Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control. • Do not force tool. Use the correct tool for your application.
,_llb WARNING: Never use a battery that has been dropped or received a sharp blow. A damaged battery is subject to explosion. Properly dispose of a dropped battery immediately. Failure to heed this warning can result in serious personal injury. Save these instructions. This manual contains • Do not operate charger with a damaged cord or plug. If damaged, have replaced immediately by a qualified serviceman. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.
-- m Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION Volts Voltage Amperes Current Hz Hertz Frequency (cycles per second) min Minutes Time '_ Alternating Current Type or a characteristic of current Direct Current Type or a characteristic of current no No Load Speed Rotational speed, at no load ...
DRILL-DRIVER 315.113320 315.113330 Chuck 3/8 in. Keyless 3/8 in. Keyless Motor DC Motor 12 Volt DC Motor 14.4 Volt Gear Train Two Speed Two Speed Switch Variable Speed Variable Speed No Load Speed 0-300 RPM (Low) 0-1000 RPM (High) 0-400 RPM (Low) 0-1400 RPM (High) Clutch 24 Positions 24 Positions Maximum Torque 210 in./Ibs 290 in./Ibs CHARGING Item No. 9 11055 Item No.
LEVEL TWO-SPEED GEARTRAIN(HI-LO) TORQUE ADJUSTMENT RING KEYLESS CHUCK REARVIEW BATTERYPACKSHOWN IN CHARGINGSTAND CHARGER DIRECTIONOF ROTATIONSELECTOR (FORWARD/REVERSE) BIT STORAGE SWITCH TRIGGER SCREWDRIVER BITS RED LIGHT (LED) BATTERYPACK SHOWNINTOOL WRISTSTRAP CHARGERSTAND 8 Fig.
,_ _ light indicates the charger is operating properly. It will remain on until battery pack is removed from charging stand or charger is disconnected from power supply. WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury.
SWITCH TO INSTALL Gee Figure2. • To turn your drill ON, depress the switch trigger. To turn it OFF, release the switch trigger. Lock switch trigger on your drill by placing the direction of rotation selector in center position. ,_ee Figure 5. • Place battery pack in your drill. Align raised rib on battery pack with groove inside drill. See Figure 4:. SWITCH TRIGGER VARIABLE Fig.
SWITCH LOCK KEYLESS CHUCK Gee Figure5. Gee Figure6. The switch trigger can be locked inthe OFF position. This feature can be used to prevent the possibility of accidental starting when not in use. To lock switch trigger, place the direction of rotation selector (Forward/Reverse Selector) in center position. Your drill has a keyless chuck. As the name implies, you can hand tighten or release drill bits in the chuck jaws. Grasp and hold the collar of the chuck with one hand.
INSTALLING BITS REMOVING BITS See Figure7. See FigureZ • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 5. • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 5. • Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use. Also, raise the front of your drill slightly to keep the bit from falling out of the chuck jaws.
BIT STORAGE DRILLING See FigureI0. See Figure12. When not in use, bits provided with your drill can be placed in the storage area located on the bottom of your drill as shown in Figure 10. SCREWDRIVER BITS BIT STORAGEAREA _IL Fig. 10 WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. Fig.
CHUCK • REMOVAL Gee Figures13,14,and 15. The chuck must be removed in order to use some accessories. To remove: • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 5. • Insert a 5/16 in. or larger hex key into the chuck of your drill and tighten the chuck jaws securely. • Tap the hex key sharply with a mallet in a clockwise direction. See Figure 13. This will loosen the screw in the chuck for easy removal.
_1 Do not abuse power tools. Abusive practices can damage tool as well as workpiece. WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. Only the parts shown on parts list, page 17, are intended to be repaired or replaced by the customer. All other parts should be replaced at a Sears Service Center. Avoid using solvents when cleaning plastic parts.
-- CRAFTSMAN 3/8 in. CORDLESS DRILL-DRIVER MODEL NOS. 315,113320 AND 315,113330 -- The model number will be found on a plate attached to the motor housing. Always mention the model number L in all correspondence regarding your 3/8 in. CORDLESS SEE BACK PAGE FOR PARTS DRILL-DRIVER ORDERING or when ordering repair parts. INSTRUCTIONS 2 1 4 PARTS LIST Part Number Description 1 616478-003 Screw (Special) .................................................................
Get it fixed, at your home or ours! For repair of major brand appliances in your own home... no matter who made it, no matter who sold ifl 1-800-4-MY-HOM EsMAnyt,me, day or night (1-800-469-4663) www.sears.com To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Sears Parts & Repair Center. 1-800-488-1222 Anyt,me, day or n,ght www.sears.
