Operator's Manual 1/2 in., 18 VOLT CORDLESS Variable Speed / Reversible DRILL-DRIVER Model No. 315.113340 Ryobi Save this manual for future reference • Safety • Features _k CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of *[his product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Visit the Craftsman web pago: www.sears.
• Table Of Contents ......................................................................................................................................................... 2 • - Warranty ......................................................................................................................................................................... 2 • Introduction ..................................................................................................................................
Your drill-driver has many features for making your drilling _IL CAUTION: Carefullyread through this entire operator'smanualbefore using your new drilL-driver. Pay close attention to the General Safety Rules, Spedllc Safety Rules and Symbols, Warnings end Cautions. if you use yourdrill-driverproperlyand only for it'sintended use, you willenjoy years of safe. reliable service. operations more pleasant and enjoyable.
Tool Use and Care • Use clamps or other practical way to secure and support the workplace to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control • Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cuttingedges are less likelyto bind and are easier to control. • Do not force tool. Use the correct tool for your application.
,_WARNING: Never use a battery that has been dropped or received a sharp blow. A damaged battery is subjectto explosion. Properly dispose of a dropped battery immediately. Failure to heed this warningcan result in serious personal injury. • Save these instructions. This manual €ontains Important safety and Operetlng Instructions for charger.
m m .Important: Some of the followingsymbolsmay be used on yourtool. Please studythem and learn their meaning.Proper interpretationof these symbolswill allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXP LANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) rain Minutes Time AlternatingCurrent Type or a characteristicof current m m Direct Current Type or a characteristicof current no NO Load Speed Rotationalspeed, at no load ..
DRILL-DRIVER Chuck Motor 315.113340 1/2in.Keytess DCMotor18Volt Gear Train Two Speed No Load Speed 0-350 RPM (Low) 0-1300 RPM (High) Clutch 24 Positions KNOW YOUR DRILL-DRIVER See Figure f. Before attempting to use yourdrill-driver,familiarize yourself with all operating features and safety requirements. KEYLESS CHUCK Maximum Torque 400 in./Ibs CHARGER Item No. 9 11041 (1425301) Rating 120 V, 60 Hz, AC only Charging Voltage 7.2 - 24 Volt Charge Rate 1 Hour BAI-rERY Item No.
TWO-SPEED GEAR TRAIN (HI-LO) KEYLESS CHUCK LEVEL TORQUE ADJUSTMENT RING REAR VIEW DIRECTION OF ROTATION SELECTOR (FORWARD/REVERSE) B_ STORAGE SCREWDRIVER BATTERYPACK SHOWNINTOOL BATTERY PACK SHOWNINCHARGER 4-1/2in. WRIST STRAP CHARGER RED LED ONIN_CATES MOD£ GREENLED ON AFTER FAST CHARGING CYCLE,INDICATESFULLYCHARGEDBATTERY PACK AND IN TRICKLECHARGE MODE. YELLOWAND GREENLEDSON INDICATESDEEPLY DISCHARGEDOR DEFECTIVEBATTERYPACK. Fig.
_ LED FUNCTIONS OF CHARGER LED WILL BE ON TO INDICATE STATUS OF CHARGER AND BATrERY PACK: WARNING: DOnot allow familiaritywith yourdrilldriver to make you careless. Remember that a careless fraction of a second is sufficientto inflict severe injury, BA'I'rERY PACK The battery packfor your tool has been shippedin a low charge conditionto prevent possibleproblems.Therefore, you shouldcharge it until light on front ofcharger changes from redto green.
SWITCH TO INSTALL BA'I-rERY PACK ,Fee Figure 2. To turn your drill ON, depress the switch trigger. To turn it OFF, release the switch trigger. • Lock switch triggeron your drillby placingthe direction of rotationselectorin center position. See F/#uFe5. • Place battery pack in yourdrill, Align raised rib on battery pack with groove inside drll{, See F3_'Ure4. FORWARD/REVERSE SELECTOR VARIABLESPEED SWITCHTRIGGER Fig.
SWITCHLOCK KEYLESS CHUCK See Figure S. See Fi#ure 6. The switch trigger can be locked in the OFF position.This feature can be used to prevent the possibilityof accidental starting when not in use. To lookswitch trigger, place the direction of rotation selector (ForWard/ReverseSelector) in center position.Note: When selector is in centar position,switch trigger is locked, SELECTOR WITH CENTER LOCK POSITION REVERSE DRILLsn" f FORWARD A Your drillh_ a keylesschuck.
INSTALLING BITS See Figure 7. REMOVING BITS B Lookthe switch trigger by placing the directionof rotationselector in center position.See F_um 5, • • Open or close chuck jaws to a point where the opening is slightlylarger than the bit size you intendto use. Also, raise the front of your drillslightlyto keep the bit from falling out of the chuck jaws. • • • See Fi#ure 7. • Insert drillbit straight into chuck the full length of the jaws as shown in Figure 7. Tighten the chuck jaws on drillbit.
BIT STORAGE Bee Figure 10. When not in use, bits provided with your drillcan be placed in the storage area located on the bottomof your drill as shown in Figure 10. LEVEL SCREWDRIVER BIT B! STORAGEAREA ,_, Fig. I0 WARNING: Always wear safety gogglesor safety glasses with side shieldswhen operating t_ols. Failureto do Socould resultin objectsbeing thrown intoyour eyes, resultingin possibleserious injury. Fig. 12 LEVEL See Figure77. A convenient feature provided with your drillis a level.
CHUCK • REMOVAL See Figures 13, 1#, and 15. The chuck must be removed in order to use some accessories. To remove: • Lock the switch trigger by placing the direction of rotation seJector in center position. See FTgure ..5.. • Insert a 5/16 in. or larger hex key into the chuck of your dnn and tighten the chuck jaws securely. • Tap the hex key sharply with a mallet in a clockwise direction. See Figure 13. This wgl loosen the screw in the chuck for easy removal.
Do not abuse power tools. Abusive prances damage tool as well as workplace. WARNING: When servicing, use only Identical Craftsman replacement parts. Use of any other part may create a hazard or cause productdamage. Only the parts shown on parts list. page 17, are intended to be repaired or replaced by the customer. All other parts should be replaced at a Sears Service Center, Avoid using solvents when cleaning pJastic parts.
i I I I I II 16 .
CRAFTSMAN 1/2 In., 18 VOLT CORDLESS DRILL-DRIVER - MODEL NO. 315.113340 in all correspondence regarding your 1/2 in., 18 VOLT CORDLESS DRILL-DRIVER or when ordering repair The parts.model number will be found on a plate attached to the motor housing. Always mention the model number SEE BACK PAGE FOR PARTS ORDERING I | INSTRUCTIONS 2 4 3 PARTS LIST Key No. Pert Number 1 975379-000 Screw (Special) ......................................................................
G:et it at, ur , ,,, For repair of major brand appliarlces in your own home... no matter who made it, no matter who sold it! 1-800-4-MY-HOM E sMAnytime, dayornight (1-800469.-4663) WW_N.seRrs.COITI To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Sears Parts & Repair Center. 1-800-488-1222 Anytime, dayor night www.sears.
