Operator's Manual I:RRFTSMRN'I 3/8 in. CORDLESS DRILL-DRIVER Reversible Model Nos. 315.114500 7.2 Volt / Two Speed 315.114510 9.6 Volt / Variable Speed 315.114500 - 7.2 VOLT Save this manual for future reference 315.114510 - 9.6 VOLT ,_ WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Visit the Craftsman web page: www.sears.
• Table Of Contents .......................................................................................................................................................... 2 • Warranty ......................................................................................................................................................................... 2 • Introduction ..................................................................................................................................
Yourdrill-driverhasmanyfeaturesformakingyourdrilling operations morepleasantandenjoyable. Safety, performance anddependability havebeengiventop priorityinthedesignofthisdrill-drivermakingiteasyto maintainandoperate. ,_ _i, Personal WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE Stay alert, watch what you are doing and use common sense when operating a power tool.
Tool Use and Care • • • • • • Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with the switch is dangerous and must be repaired.
• Never use a battery that has been dropped or received a sharp blow. A damaged battery is subject to explosion. Properly dispose of a dropped battery immediately. Failure to heed this warning can result in serious personal injury. • Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.
Important:Someof the interpretation following symbols may be used on your tool. Please study them and learn their meaning. Proper of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) min Minutes Time Alternating Current Type or a characteristic of current Direct Current Type or a characteristic of current No Load Speed Rotational speed, at no load V no ...
DRILL-DRIVER 315.114500 315.114510 Chuck Motor Switch No Load Speed Clutch 3/8 in. Keyless DC Motor 7.2 Volt 3/8 in. Keyless DC Motor 9.6 Volt Two Speed 250 / 550 RPM 24 Positions 70 in.lb. Item No. =11050 Variable Speed 0-600 RPM 24 Positions (981496-001) 120 V, 60 Hz, AC only 7.2 Volt 3-6 Hours (1425003) 120 V, 60 Hz, AC only 9.6 Volt Maximum Torque CHARGER Rating Charging Voltage Charge Rate BATTERY PACK "Craftsman 90 in.lb. Item No. 311053 Item No. _11051 3-6 Hours Item No.
LEVEL MODEL 315.114500 CHARGER TORQUE 7,2 VOLT KEYLESS CHUCK SWITCH TRIGGER DIRECTIONOF ROTATIONSELECTOR (FORWARD/REVERSE) SCREWDRIVER BIT BIT STORAGE BATTERYPACK SHOWNINTOOL CHARGER PLUG INPUTJACK KEYLESS CHUCK TORQUE ADJUSTMENT RING WRIST STRAP Fig. 1 (a) MODEL 315.114510 9.6 VOLT LEVEL BATTERY PACKSHOWN IN CHARGINGSTAND CHARGER SWITCH TRIGGER DIRECTIONOF ROTATIONSELECTOR (FORWARD/REVERSE) \ BIT STORAGE SCREWDRIVER BITS RED LIGHT (LED) BATTERY PACK WRIST STRAP CHARGING STAND 8 F
_k CHARGING BATTERY MODEL 315.114510 WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. PACK FOR See Figure 1 (b). • Charge battery pack only with the charging assembly provided. • Make sure power supply is normal household voltage, 120 volts, 60 Hz, AC only. • Connect charger to power supply.
SWITCH TO INSTALL BAI-rERY See Figure 2. • To turn your drill ON, depress the switch trigger. To turn it OFF, release the switch trigger. Lock switch trigger on your drill by placing the direction of rotation selector in center position. See Figure 4. • Place battery pack in your drill. Align raised rib on battery pack with groove inside drill. See Figure 3. SWITCH TRIGGER TWO SPEED (MODEL PACK BATTERY PACK Fig. 2 315.114500) LATCHES Drill model 315.
SWITCH LOCK KEYLESS CHUCK See Figure 4. See Figure 5. The switch trigger can be locked in the OFF position. This feature can be used to prevent the possibility of accidental starting when not in use. To lock switch trigger, push the direction of rotation selector (Forward/Reverse Selector) to the center position. Your drill has a keyless chuck. As the name implies, you can hand tighten or release drill bits in the chuck jaws. Grasp and hold the collar of the chuck with one hand.
INSTALLINGBITS REMOVING BITS See Figure 6. See Figure 6. • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 4. • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 4. • Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use. Also, raise the front of your drill slightly to keep the bit from falling out of the chuck jaws.
BIT STORAGE DRILLING See Figure 9. See Figure 11. When not in use, bit(s) provided with your drill can be placed in the storage area located on the bottom of your drill. As shown in Figure 9, model 315.114500 has one bit storage slot and model 315.114510 has two bit storage slots. SCREWDRIVER 315.114500 315.114510 _J_ SCREWDRIVER BIT BIT STORAGEAREA ,_ Fig. 11 Fig. 9 When drilling hard smooth surfaces use a center punch to mark desired hole location.
• CHUCKREMOVAL Insert hex key in chuck and tighten chuck jaws securely. Tap sharply with a mallet in a counterclockwise direction. This will loosen chuck on the spindle. It can now be unscrewed by hand. See Figure 14. See Figures 12, 13, and 14. The chuck must be removed in order to use some accessories. To remove: • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 4. • Insert a 5/16 in.
_L Do not abuse power tools. Abusive practices can damage tool as well as workpiece. WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. Only the parts shown on parts list, pages16 and !7, are intended to be repaired or replaced by the customer. All other parts should be replaced at a Sears Service Center. Avoid using solvents when cleaning plastic parts.
CRAFTSMAN 3/8 in. CORDLESS MODEL I DRILL-DRIVER NO, 315.114500 The in allmodel correspondence numberwill regarding be found on your a plate 3/8 in, attached CORDLESS to the motor DRILL-DRIVER housing. Always or when mention ordering the model repair number parts. SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS MODEL 315.114500 2 PARTS LIST Key No. Part Number Description 1 616478-003 Screw (Special) .................................................................
CRAFTSMAN I 3/8 in. CORDLESS DRILL-DRIVER MODEL NO. 315.114510 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your 3/8 in. CORDLESS DRILL-DRIVER or when ordering repair parts. SEE BACK PAGE FOR PARTS ORDERING I I INSTRUCTIONS MODEL 315.114510 2 4 PARTS LIST Key No. Part Number Description 1 616478-003 Screw (Special) .................................................................
Get it fixed,lat VoUEl omeer ours! Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold itt For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME Call anyttme, ® (1-800-4694663) day or night(U.S.A www.sears.com and Canada) www.
