_l, Ryobi !I I Operator's Manual I:RRFTSMRN'I 318 in. CORDLESS DRILL-DRIVER Variable Speed / Reversible Model Nos. 315.11452012 Volt 315.114530 - 14.4 Volt Save this manual for future reference WARNING: ToreducetheriskofInjury,the user must read and understand the operator's manual before using this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Visit the Craftsman web page: www.sears.
• Table of Contents ........................................................................................................................................................... 2 • Warranty ......................................................................................................................................................................... 2 • Introduction .................................................................................................................................
Your drill-driverhas many features for making yourdrilling operationsmore pleasant and enjoyable. Safety, performanceand dependabilityhave been given top priorityin the design of this drill-drivermaking it easy to maintain and operate. _kWARNING: Reed and understand all Inatructlons. Failure to follow all instructionslistedbelow, may resultin electric shock,fire and/or seriouspersonal Injury.
Tool Use and Care • • • • • • Use clamps or other practical way to secure and support the workplace to a stable platform. Holding the work by hand or against your body Is unstable and may [sadto loss of control. Do not fame tool. Use the correct tool for your application. The correcttool will do the job Petterand safer at the rate for which it is designed. no not use tool if switch does not turn it on or off. A tool that cannot be controfled with the switchis dangerousand must be repaired.
• Neverusea battery that has been dropped or received a sharp blow. A damaged battery Is subjectto explosion, Properlydispose of a dropped battery immediately.Failure to heed this warning can resultIn serious personal injury. • Do not operate charger I! It has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. FolioNIng this rule will reduce the risk of electric shock, fire, or sedous personal Injury.
Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME D ESIG NATION/F..
DRILL-DRIVER Chuck Motor Gear Train Switch No Load Speed Clutch Maximum Torque CHARGING ASSEMBLY Rating Charging Voltage Charge Rate BATTERY PACK • Craftsman 315.114520 3/8 In. Keyless DC Motor 12 Volt Two Speed Variable Speed 0-300 RPM (Low) O-1000 RPM (High) 24 Positions 225 In,lb. Item No. =11055 (1425004) 1 20 V, 60 Hz, AC only 12 Volt 3-6 Hours Item No. !11057 (1322549) 315.114530 3/8 in. Keyless DC Motor 14.4 Volt Two Speed Vadabls Speed 0-400 RPM (Low) 0-1400 RPM (High) 24 PoslUons 275 In,lb.
TWO-SPEED GEARTRAIN(HI&O) LEVEL TORQUE ADJUSTMENT RING KEYLESS CHUCK BATFERYPACKSHOWN IN CHARGING STAND CHARGER REARVIEW DIRECTION OF ROTATION SELECTOR (FORWARD/REVERSE) SWITCH TRGGER RED UGHT (LED) SCREWDRIVER BATTERYPACK SHOWN DIT STORAGE CHARGERSTAND 315,114520 BATTERY PACK SHOWN IN CHARGER WRIST STRAP CHARGER 315.114530 4-1/2In, ' CYCLE,INDICATESFULLYCHARGEDBA'n'ERY PACK ANDIN TRICKLE CHARGEMODEL YELLOWAND GREENLEDSON INDICATESDEEPLY DISCHARGEDOR DEFECTIVEBATTERYPACK. 8 Fig.
_ _ WARNING : Always wear safety gogglesor safety glasses with side shields when operatingtools. Failure to do so could result In objects being thrown intoyour eyes, resultingin possible sedousinjury, WARNING: 0o not allow famillahtywith yourdrilLdriver to make you careless, Remember thet a careless fraction of a second Is suffic[ertto inflict severe injury, BATTERY PACK (MODEL 315.114520) The battery pack for your tool has been shipped in alow charge condition to prevent possible problems.
A LED FUNCTIONS OF CHARGER LED WILL BE ON TO INDICATE STATUS OF CHARGER AND BATTERY PACK: (MODEL 315.114520) WARNING: Do not allow familiarity with your drilldriver to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. BATTERY PACK (MODEL 315.114520) The battery pack for your tool has been shipped In a low charge condition to prevent possible prebiems. Therefore, you should charge it until light on front of charger changes from red to green.
SWITCH See Figure 2. TO INSTALL BATI'ERY RI Lockswitchtflggeronyourdrlll by placing the direction of rotationselectorIn center position,See Figure 5. • Place battery peck In your drill. Align raised fib on battery pack with groove insideddll. See Figure 4. To turn your drillON, depress the switchtdgger. To turn It OFF, release the switch trigger, SWITCH TRIGGER VARIABLE PACK Fig.
SWITCH LOCK KEYLESS CHUCK See Figure 5, See Figure 6. The switch trigger can be locked In the OFF position. This feature can be used to prevent the possibilityof accidental starting when not In use. To lock switch tdgger, place the directionof rotation selector (Forward/Reverse Selector) in center position. Yourdrillhas a le_ylesschuck,As me name implies,you can hand tighten or releaseddl]bits in the chuckjaws. Graspand ho4dthe collarofthe chuckwith one hand.Rotate the chuck bodywithyourother hand.
INSTALLING See Figure 7. REMOVING BITS BITS See Figure Z • Lock the switch trigger by placing the direction of rotation selector in center position, See Figure 5, • Lock the switch trigger by placing the direction of rotation selector in center position. Sea Figure 5. • Open or close chuck jaws to a point where the opening Is slightly larger than the bit size you intend to use. Also, raise the front of your drill slightly to keep the bit from falling out of the chuck Jaws.
BITSTORAGE DRILLING See Figure 10. See Figure 12. When not in use, bits provided with your drill can be placed in the storege area located on the bottom of your drill as shown in Figure 10, BI1 STORAGE AREA Fig. 10 _k WARNING; Always wear salaty goggles or safety glasses with side shields when operating tools, Fig. 12 Fal]ureto do so could resultin objects being thrown Intoyour eyes, resultingIn possibleseriousInjury.
CHUCK REMOVAL • See Figures 13, 14, and 1.5. The chuck must be removed In order to use some aGcessories. To remove: • Lock the switch trigger by placing the direction ot rotation selector in center position. See Figure 5. • Insert a 5/16 in. or larger hax _ into the chuck of your ddll and tighten the chuck jaws securely. • Tap the hex key sharply with a mallet In a clockwise direction. See Figure 13. This will loosen the screw in the chuck for easy removal.
A Do not abuse power tools. Abusive practices can damage tool as well as wor_
CRAFTSMAN 3/8 In. CORDLESS DRILL=DRIVER MODEL NOS. 315.114520 AND 315.114530 I The model numberwill befound on a plateattachedto the motor houslng.Alwaysmention the model number In all correspondence regardingyour 3/8 In. CORDLESS DRILL-DRIVER arwhen orderlngrepalr parts. SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS 2 3 \ I 3 4 PARTS LIST Key No. 1 2 3 Part Number Description 616478-003 Screw (Special) ................................................................. 1 6903326 Quan.
Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME ® (1400-469-4663) Call anytime, day or night(U.S.A, www.sears.com and Canada) www.sears.
