Operator's Manual 3/8 in., 18 VOLT CORDLESS DRILL-DRIVER Variable Speed / Reversible Model No. 315.114610 Save this manual future reference for • • • • • _, CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Visit the Craftsman web page: www.sears.
• Warranty ......................................................................................................................................................................... 2 • Introduction ..................................................................................................................................................................... 3 • General Safety Rules ....................................................................................................................
• w Your drill-driver has many features for making your drilling operations more pleasant and enjoyable. Safety, performance and dependability have been given top priority in the design of this drill-driver making it easy to maintain and operate. _, _k • Dress properly. DO not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. • Avoid accidental starting.
• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to bind and are easier to control. • Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool's operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. Use only accessories that are recommended by the manufacturer for your model.
_. WARNING: Read and understand all instructions. c. That wire size is large enough for AC ampere rating of charger as specified below: Failure to follow all instructionslisted below, may result in electric shock, fire and/or serious personal injury. Cord Length (Feet) 25' 50' 100' Cord Size (AWG) 16 16 16 Note: AWG = American Wire Gage • Never usea battery that has been dropped or received a sharp blow. A damaged battery is subject to explosion.
Important:Someofthefollowingsymbolsmaybeusedonyourtool.Pleasestudythemandlearntheirmeaning.Proper interpretation of thesesymbolswillallowyoutooperatethetoolbetterandsafer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) min Minutes Time Alternating Current Type or a characteristic of current Direct Current Type or a characteristic of current no No Load Speed Rotational speed, at no load ...
DRILL-DRIVER 315.114610 Maximum Torque Chuck 3/8 in. Keyiess CHARGER Motor DC Motor 18 Volt Gear Train Two Speed Rating 120 V, 60 Hz, AC only No Load Speed 0-350/min. (Low) Charging Voltage 18 Volt 0-1300/min (High) Charge Rate 3-6 Hours 24 Positions BATTERY Item No. 9 11378 Clutch 337 in.lb. Item No. 9 11379 (1426161 ) PACK (1323620) KNOW YOUR DRILL-DRIVER FORWARD/REVERSE SELECTOR See Figure 1.
TWO-SPEED GEARTRAIN(HI-LO) LEVEL TORQUE ADJUSTMENT RING KEYLESS CHUCK REARVIEW DIRECTIONOF ROTATIONSELECTOR (FORWARD/REVERSE) SWITCH TRIGGER BATTERYPACKSHOWN IN CHARGINGSTAND BIT STORAGE CHARGER SCREWDRIVER BITS BATTERYPAq SHOWNINTOOL WRIST STRAP Fig.
,_ remain on until battery pack is removed from charging stand or the charger is disconnected from power supply. WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. • Note: If charger does not charge battery pack, return battery pack and charger to your nearest Sears Repair Center for electrical check.
SWITCH TO INSTALL See Figure 2. • To turn your drill ON, depress the switch trigger. To turn it OFF, release the switch trigger. Lock switch trigger on your drill by placing the direction of rotation selector in center position. See Figure 5. • Place battery pack in your drill. Align raised rib on battery pack with groove inside drill. See Figure 4. FORWARD/REVERSE SELECTOR VARIABLESPEED SWITCHTRIGGER VARIABLE BATTERY PACK BATTERY Fig.
SWITCH LOCK KEYLESS CHUCK See Figure 5. See Figure 6. The switch trigger can be locked in the OFF position. This feature can be used to prevent the possibility of accidental starting when not in use. To lock switch trigger, place the direction of rotation selector (Forward/Reverse Selector) in center position. Note: When selector is in center position, switch trigger is locked. Your drill has a keyless chuck. As the name implies, you can hand tighten or release drill bits in the chuck jaws.
INSTALLINGBITS SeeFigure7. See Figure 7. • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 5. • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 5. • Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use. Also, raise the front of your drill slightly to keep the bit from falling out of the chuck jaws. • Loosen the chuck jaws from drill bit.
BIT STORAGE DRILLING See Figure 10. See Figure 12. When not in use, bits provided with your drill can be placed in the storage area located on the bottom of your drill as shown in Figure 10. LEVEL SCREWDRIVER BIT I ILr_ i f=,...,...=...=.-= STORAGEAREA _IL Fig. 10 WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. Fig. 12 LEVEL See Figure 11.
CHUCK REMOVAL • See Figures 13, 14, and 15. The chuck must be removed in order to use some accessories. To remove: • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 5. • Insert a 5/16 in. or larger hex key into the chuck of your drill and tighten the chuck jaws securely. Insert hex key in chuck and tighten chuck jaws securely. Tap sharply with a mallet in a counterclockwise direction. This will loosen chuck on the spindle.
_ Do not abuse power tools. Abusive practices can damage toot as well as workpiece. WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. Only the parts shown on parts list, page 17, are intended to be repaired or replaced by the customer. All other parts should be replaced at a Sears Service Center. Avoid using solvents when cleaning plastic parts.
CRAFTSMAN 3/8 in., 18 VOLT CORDLESS DRILL-DRIVER - MODEL NO. 315.114610 l SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS 2 4 3 PARTS LIST Key No. Part Number Description Quan. 1 6613401 Screw (Special) ...................................................................... 1 2 6903330 Chuck ..................................................................................... 1 3 *Item No. 9 11378 Battery Pack (1323520) .........................................................
Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME Call anytime, ® (1-800-469-4663) day or night (U.S.A. and Canada) www.sears.com www.sears.
