Operator's Manual 318 in., 15.6 VOLT CORDLESS DRILL-DRIVER Variable Speed / Reversible Model No. 315.114630 Save this manual future reference for • Safety • Features --A_WARNING: Toreduce the risk of injury, the user must read and understand the operator's manual before using this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Visit the Craftsman web page: www.sears.
• Warranty ......................................................................................................................................................................... 2 • Introduction ..................................................................................................................................................................... 2 • General Safety Rules ....................................................................................................................
_1_ WARNING: Read and understand all instructions. Failure to fellow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE WORK AREA • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
SERVICE • • Tool service must be performed only by qualified repair personnel. Service or maintenance performed ment parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of shock or injury.
c. That wire size is large enough for AC ampere rating of charger as specified below: _ILWARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. • Never use a battery that has been dropped or received a sharp blow. A damaged battery is subject to explosion. Properly dispose of a dropped battery immediately. Failure to heed this warning can result in serious personal injury.
Important:Someofthefollowingsymbolsmaybeusedonyourtool.Pleasestudythemandlearntheirmeaning.Proper interpretation of thesesymbolswillallowyoutooperatethetoolbetterandsafer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) min Minutes Time Alternating Current Type or a characteristic of current -'='= Direct Current Type or a characteristic of current no No Load Speed Rotational speed, at no load ...
24 Positions Chuck.......................................................... 3/8in. Keyless Clutch............................................................. Motor.............................................................. 15.6VoltDC ChargerInput................................. 120V, 60Hz,AConly 3-6Hours Switch....................................................... VariableSpeed ChargeRate....................................................... Torque....................................................
LEVEL TORQUE ADJUSTMENT RING KEYLESS CHUCK REARVIEW DIRECTIONOF ROTATIONSELECTOR (FORWARD/REVERSE) BIT STORAGE SWITCH TRIGGER SCREWDRIVER BITS BATTERYPACKSHOWN IN CHARGINGSTAND CHARGER BATTERYPACK SHOWNINTOOL WRISTSTRAP RED LIGHT (LED) CHARGERSTAND Fig.
,_ light indicates the charger is operating properly. It will remain on until battery pack is removed from charging stand or charger is disconnected from power supply. WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury.
SWITCH TO INSTALL See Figure 2. • To turn your drill ON, depress the switch trigger. To turn it OFF, release the switch trigger. Lock switch trigger on your drill by placing the direction of rotation selector in center position. See Figure 4. • Place battery pack in your drill. Align raised rib on battery pack with groove inside drill. See Figure 3. SWITCH TRIGGER VARIABLE Fig.
SWITCH LOCK KEYLESS CHUCK See Figure 4. See Figure 5. The switch trigger can be locked in the OFF position. This feature can be used to prevent the possibility of accidental starting when not in use. To lock switch trigger, place the direction of rotation selector (Forward/Reverse Selector) in center position. Your drill has a keyless chuck. As the name implies, you can hand tighten or release drill bits in the chuck jaws. Grasp and hold the collar of the chuck with one hand.
INSTALLINGBITS REMOVING See Figure 6. See Figure 6. • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 4. • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 4. • Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use. Also, raise the front of your drill slightly to keep the bit from falling out of the chuck jaws.
BIT STORAGE DRILLING See Figure 9. See Figure11. When not in use, bits provided with your drill can be placed in the storage area located on the bottom of your drill as shown in Figure 9. SCREWDRIVER BITS BIT STORAGEAREA Fig. 9 d_k WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. Fig.
CHUCK REMOVAL • See Figures 12, 13, and 14. The chuck must be removed in order to use some accessories. To remove: • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 4. • Insert a 5/16 in. or larger hex key into the chuck of your drill and tighten the chuck jaws securely. Insert hex key in chuck and tighten chuck jaws securely. Tap sharply with a mallet in a counterclockwise direction. This will loosen chuck on the spindle.
,1_ Do not abuse power tools. Abusive practices can damage toot as well as workpiece. WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. Only the parts shown on parts list, page 17, are intended to be repaired or replaced by the customer. All other parts should be replaced at a Sears Service Center. Avoid using solvents when cleaning plastic parts.
i i r M i r r i 16
CRAFTSMAN 318 in., 15.6 VOLT CORDLESS MODEL NO. 315.114630 DRILL-DRIVER -- The model number will be found on a plate attached to the motor housing. Always mention the model number __ in all correspondence regarding your 3/8 in. CORDLESS SEE BACK PAGE FOR PARTS DRILL-DRIVER ORDERING or when orde_ INSTRUCTIONS 2 1 4 3 PARTS LIST Key No. Part Number Description 1 660120002 Screw (Special) ................................................................. 1 2 690033002 Chuck (Item No.
Get it fixed, at your home or ours! Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME ® (1-800-469-4663) Call anytime, day or night (U.S.A. and Canada) www.sears.com www.
