PERATOR'S MAN AL ® 1/2 in. 19.2 VOLT CORDLESS DRILL-DRIVER VARIABLE SPEED/REVERSIBLE Model Nos. 315.114852 315.114853 A WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Craftsman Consumer Sears, Roebuck Helpline: 1-800-932-3188 and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: www.sears.
[] Warranty .......................................................................................................................................................................... 2 [] Introduction ..................................................................................................................................................................... 2 [] General Safety Rules ...................................................................................................................
_ WARNING!READANDUNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. SAVE THESE WORK [] Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. iNSTRUCTiONS AREA [] Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
[] [] Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may create a risk of injury when used on another tool. Keep the tool and its handle dry, clean and free from oil and grease. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products, or any strong solvents to clean your tool. Following this rule will reduce the risk of loss of control and deterioration of the enclosure plastic.
A WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. [] Before using battery charger, read all instructions and cautionary markings in this manual, on battery charger, battery, and product using battery to prevent misuse of the products and possible injury or damage.
Someof the followingsymbolsmaybe usedon this product.Pleasestudythemandlearntheir meaning.Proper interpretation ofthesesymbolswill allowyouto operatetheproductbetterandsafer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current mz Hertz Frequency (cycles per second) W Watt Power Minutes Time Alternating Current Type of current Direct Current Type or a characteristic no No Load Speed Rotational speed, at no load [] Class II Construction Double-insulated ...
Thefollowingsignalwordsandmeanings areintendedto explainthe levelsof riskassociatedwiththis product. SYMBOL _lk SIGNAL MEANING DANGER: Indicates imminently in death oranserious injury.hazardous situation, which, if not avoided, will result WARNING: CAUTION: CAUTION: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
PRODUCT SPECIFiCATiONS Chuck .......................................................... 1/2 in. Keyless Motor ............................................................... 19.2 Volt DC Clutch ................................................................ 24 Position Torque ................................................................... 410 in.lb. Switch .............................. VSR (Variable Speed Reversible) Charger Input .................................... Gear Train ...........
KNOW YOUR DRILL DRIVER See Figure 1. The safe use of this product requires an understanding of the information on the product and in this operator's manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features and safety rules. KEYLESS CHUCK The keyless chuck allows you to hand-tighten the drill bit in the chuck jaws.
UNPACKING This product has been shipped completely assembled. WARNING: If any parts are damaged or missing do not operate this product until the parts are replaced. Failure to heed this warning could result in serious personal injury. [] Carefully remove the product and any accessories from the box. Make sure that all items listed in the packing list are included. A [] Inspect the product carefully to make sure no breakage or damage occurred during shipping.
BATTERY PROTECTION FEATURES [] Press down on the battery pack to be sure contacts on the battery pack engage properly with contacts in the charger. DieHardo 19.2 V lithium-ion battery packs are designed with features that protect the lithium-ion cells and maximize battery life. [] Normally the red LED on charger will come on. This indicates the charger is in fast charging mode. If the tool stops during use, release the trigger to reset and resume operation.
CHARGING A HOT BATTERY PACK TO iNSTALL BATTERY PACK See Figure 3. When using the product continuously, the batteries in the battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge. When the battery pack becomes discharged and is hot, this will cause the green LED to come on instead of the red LED. After 30 minutes, reinsert the battery pack in the charger.
A To stop the drill, release the switch trigger and allow the chuck to come to a complete stop. NOTE: The drill will not run unless the direction of rotation WARNING: Battery tools are always in operating condition. Therefore, switch should always be locked when not in use or carrying at your side. selector is pushed fully to the left or right. DiRECTiONOF ROTATIONSELECTOR (FORWARD/REVERSE/CENTER LOCK) Avoid running the drill at low speeds for extended periods of time.
TWO=SPEED GEAR TRAIN ADJUSTABLE See Figure 6. CLUTCH This product is equipped with an adjustable torque clutch for driving different types of screws into different materials. The proper setting depends on the type of material and the size of screw you are using. The drill has a two-speed gear train designed for drilling or driving at LO (1) or HI (2) speeds. A slide switch is located on top of the drill to select either LO (1) or HI (2) speed.
INSTALLINGBITS REMOVING See Figure 8. See Figure 8. [] Lock the switch trigger by placing the direction of rotation selector in the center position. [] Lock the switch trigger by placing the direction of rotation selector in the center position. [] Open or close the chuck opening is slightly larger use. Also, raise the front bit from falling out of the [] Open the chuck jaws. jaws to a point where the than the bit size you intend to of the drill slightly to keep the chuck jaws.
DRILLING See Figures 11 - 12.. Levels are located on the top and end of the motor housing to help keep the drill bit level during use. [] Check the direction of rotation selector for the correct setting (forward or reverse). [] Secure the material to be drilled in a vise or with clamps to keep it from turning as the drill bit rotates. [] Hold the drill firmly and place the bit at the point to be drilled. [] Depress the switch trigger to start the drill.
METAL DR(LLING • Overheat the drill; For maximum performance, use high speed steel bits for metal or steel drilling. • Wear the bearings; • Bend or burn bits; and == Select normal drilling mode. == Begin drilling at a very low speed to prevent the bit from slipping off the starting point. == Maintain a speed and pressure which allows cutting without overheating the bit. Applying too much pressure will: • Produce off-center or irregular-shaped holes.
CHUCK REMOVAL See Figures 13- 15. MALLET The chuck may be removed and replaced by a new one. [] Lock the switch trigger by placing the direction of rotation selector in center position. [] Insert a 5/16 in. or larger hex key into the chuck of the drill and tighten the chuck jaws securely. [] Tap the hex key sharply with a mallet in a clockwise direction. This will loosen the screw in the chuck for easy removal. MALLET HEX KEY Fig. 15 CHUCKJAWS \ TO RETIGHTEN A LOOSE CHUCK The chuck may become loose o
CRAFTSMAN 1/2 in., 19.2 VOLT CORDLESS DRILL-DRIVER MODEL NOS. 315.114852 and 315.114853 The model number will be foundregarding on a plate attached to the motor housing. Always mention number in all correspondence your DRILUDRiVER or when ordering repair parts, the model SEE BACK PAGE FOR PARTS ORDERING J | INSTRUCTIONS 2 4 3 PARTS Key No. Part Number 1 6613402 2 6903323 3 LIST Description Qty. Screw (Special) ................................................................................
Your Home For expert troubleshooting and home solutions advice: www.managemyhome.com For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters.