Operator's Manual 3/8 in. CORDLESS DRILL-DRIVER Variable Speed / Reversible Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: www.sears.
Warranty..........................................................................................................................................................................2 Introducton .....................................................................................................................................................................2 General Safety Rules ....................................................................................................................................
VVARNING: read AND UNDERSTAND ALL IN STRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or seri™ ous personal injury. ■ ■ SAVE THESE INSTRUCTIONS WORK AREA ■ Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. ■ ■ Do not operate power tools in explosive atmo spheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
SERVICE ■ Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury. When servicing a tool, use only Identical replace ment parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of shock or injury. IH::!:....
WARNING; Never use a battery that has been dropped or received a sharp blow. A damaged battery is subject to explosion. Properly dispose of a dropped battery immediately. Failure to heed this warning can result in serious personal injury. Before using battety charger, read all Instructions and cautionary markings In this manual, on battery charger, and product using battery charger. Fol lowing this ruie will reduce the risk of electric shock, fire, or serious personal injury.
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta tion of these symbols wil! allow you to operate the tool better and safer.
The foliowing signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL A A A SIGNAL MEANING DANGER: V\^ARNING: CAUTION: CAUTION: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, could result in Death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
product speCIFíCATIONS DRILL-DRIVER Chuck Motor Gear Train Switch No Load Speed Battery Maximum Torque Charger Rating Charge Rate Clutch 315.115200 3/8 in. Keyless 13.2 Volts One Speed Variable Speed 0'600/min 130139018 100 in.lb. 140287001 120 V, 80 Hz,AC only 3-6 Hour 24 Positions 315.115210 3/8 in. Keyless 15.6 Volts One Speed Variable Speed 0-800/min 130139015 110 in.lb. 140250013 120 V 60 Hz,AConiy 3-6 Hour 24 Positions KNOW THIS TOOL DIRECTION OF ROTATION SELECTOR See Figure 1.
BIT STORAGE TORQUE ADJUSTMENT RING SCREWDRIVER BITS KEYLESS CHUCK DIRECTION OF ROTATION SELECTOR (FORWARD / REVERSE) BATTERY CHARGING STAND RED LIGHT WRIST STRAP CHARGER instructions Your drill has been shipped completely assembled. ■ Carefully remove the too! and accessories from the box. ■ Make sure that all items listed in the packing list are included. ■ Inspect the tool carefully to make sure no breakage or damage occured during shipping.
WARNING: Do not allow familiarity with this tool to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. INFORMATION FOR RECHARGING HOT BAT TERY PACK When using this tool continuously, the batteries in your battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before at tempting to recharge. Note: This situation only occurs when continuous use of your drill causes the batteries to become hot.
SVtflTCH See Figure 2. To turn your drill ON, depress the switch trigger. To turn it OFF, release the switch trigger. TO INSTALL BATTERY PACK ■ Lock switch trigger on this drill by placing the direction of rotation selector in center position. See Figure 4. ■ Place battery pack in this drill. Align raised rib on battery pack with groove inside drill. See Figure 3.
SVtflTCH LOCK See Figure 4. The switch trigger can be locked in the OFF position. This feature can be used to prevent the possibility of accidenta! starting when not in use. To lock switch trigger, place the direction of rotation selector (Forward/Reverse Selector) in center position. SELECTOR WITH CENTER LOCK POSITION KEYLESS CHUCK See Figure 5. Your drill has a keyless chuck. As the name implies, you can hand tighten or release drill bits in the chuck jaws.
INSTALLING BITS See Figure 6. ■ Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 4. ■ Open or close chuck jaws to a point where the open ing is slightly larger than the bit size you intend to use. Also, raise the front of your drill slightly to keep the bit from falling out of the chuck jaws. ■ Insert drill bit straight into chuck the full length of the jaws as shown in Figure 6. ■ Tighten the chuck jaws on drill bit.
DR|j_|_|fijQ BIT STORAiaE See Figure 9. When not in use, bits provided with your drill can be placed in the storage area located on the bottom of your drill as shown in Figure 9. SCREWDRIVER BITS See Figure 10. BIT STORAGE AREA Always wear safety goggles or safety A WARNING: glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. Fig.
Insert hex key in chuck and tighten chuck jaws se curely. Tap sharpiy with a mallet in a counterclockwise direction. This will loosen chuck on the spindle. It can now be unscrewed by hand. See Figure 13. CHUCK removal See Figures 11; 12, and 13. The chuck must be removed in order to use some acces sories. To remove: ■ Lock the switch trigger by placing the direction of rota tion selector in center position. See Figure 4. ■ Insert a 5/16 in.
WARNING: When servicing, use oniy identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc. Do not abuse power tools. Abusive practices can damage tool as well as workpiece.
CRAFTSMAN 3/8 in,, 13.2 VOLT CORDLlSS DRILL-DRIVER ™ MODEL NO. 315.116200 The model number wifi be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your 3/8 In., 13.2 VOLT CORDLESS DRILL-DRIVER or when ordering repair parts. see back page for parts ordering instructions PARTS LiST Key No. 1 2 3 4 5 ^_____________ Part Number Description 660120002 690033002 130139018 140287001 300912088 983000-170 Qty. ........... 1 Screw (Special).........
CRAFTSMAN 3/8 in,, 15.6 VOLT CORDLlSS DRILL-DRIVER ™ MODEL NO. 315.116210 The model number wifi be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your 3/8 In., 15.6 VOLT CORDLESS DRILL-DRIVER or when ordering repair parts. see back page for parts ordering instructions PARTS LiST Key No. 1 2 3 4 5 Part Number Description Qty. Screw (Special)...................................................................... 1 Chuck ......................
