RATOR'S MANUAL 3/8 in., 14.4 VOLT CORDLESS DRILL=DRiVER VARIABLE SPEED/REVERSIBLE Model No. 315.115470 A WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: www.sears.
[] Warranty .......................................................................................................................................................................... 2 [] Introduction ..................................................................................................................................................................... 2 [] General Safety Rules ...................................................................................................................
,_. WARNINGX Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mainsoperated (corded) power tool or battery-operated (cordless) power tool. [] [] SAVE THESE WORK INSTRUCTIONS AREA SAFETY [] Keep work area clean and well lit. Cluttered or dark areas invite accidents.
[] Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. BATTERY TOOL USE AND CARE [] Ensure the switch is in the off position before inserting battery pack.
A WARNINGX READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. [] Before using battery charger, read all instructions and cautionary markings in this manual, on battery charger, battery, and product using battery to prevent misuse of the products and possible injury or damage.
Someofthefollowingsymbolsmaybeusedonthistool.Pleasestudythemandlearntheirmeaning.Properinterpretation ofthesesymbolswillallowyouto operatethetoolbetterandsafer. SYMBOL _ DESIG NATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power min Minutes Time "L, Alternating Current Type of current .
Thefollowingsignalwordsandmeanings areintendedto explainthe levelsofriskassociatedwiththis product. SYMBOL SIGNAL MEANING ,_ DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. ,_ WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
PRODUCT SPECIFICATIONS Chuck .......................................................... Motor .............................................................. 3/8 in. Keyless 14.4 Volt DC Clutch ................................................................ 24 Position Torque ................................................................... Switch .............................. VSR (Variable Speed Reversible) Charger Input ................................... Gear Train ...........................
KNOW YOUR DRILL-DRIVER KEYLESS See Figure 1. Before attempting to use this product, familiarize yourself with all operating features and safety rules. AUTO LOCK SELECTOR Bits can be changed quickly using the auto lock chuck feature. Placing the auto lock selector in auto lock mode and changing the direction of rotation will open the chuck jaws or tighten them around the bit. BIT STORAGE Bits provided with the drill-driver can be placed in the storage area, located on the base of the drill.
A CHARGING WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious A [] Charge the battery pack only with the charger provided. [] Make sure the power supply is normal household voltage, 120 volts, 60 Hz, AC only. WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories [] Connect the charger to the power supply.
CHARGINGA HOTBATTERYPACK Whenusingthetoolcontinuously, thebatteriesinthe batterypackwillbecomehot.Youshouldlet a hot battery TO iNSTALL BATTERY PACK See Figure 3. [] Lock switch trigger on the drill by placing the direction of rotation selector in center position. pack cool down for approximately 30 minutes before attempting to recharge. When the battery pack becomes discharged and is hot, this will cause the green LED to come on instead of the red LED.
_1_ WARNING:Batterytoolsarealwaysinoperating condition.Therefore, switchshouldalwaysbelocked whennotinuseor carryingatyourside. REVERSE To stop the drill, release the switch trigger and allow the chuck to come to a complete stop. NOTE: The drill will not run unless the direction of rotation selector is pushed fully to the left or right. Avoid running the drill at low speeds for extended periods of time.
AUTO LOCKCHUCK TWO-SPEED See Figure 6. See Figure 7. Bits can be changed quickly using the auto lock chuck feature. In auto lock mode, the chuck jaws open when the direction of rotation selector is set for reverse rotation The drift has a two-speed gear train designed for drilling or driving at LO (t) or Hi (2) speeds. A slide switch is located on top of the drift to select either LO (1) or Hi (2) speed.
ADJUSTABLETORQUE LED WORKLIGHT CLUTCH See Figure 9. This product is equipped with an adjustable torque clutch for driving different types of screws into different materials. The proper setting depends on the type of material and the size of screw you are using. ADJUSTING The LED worklight on the foot of the drill will come on when the switch trigger is depressed. This provides additional lighting on the surface of the workpiece for operation in lower-light areas. TORQUE See Figure 8.
INSTALLING AND REMOVING BITS Fully depress the switch trigger to tighten the chuck jaws on the drill bit. There are two methods for installing and removing bits. You can choose the auto lock feature to quickly open and close the chuck jaws, or you can use the keyless chuck. USING THE AUTO LOCK FEATURE NOTE: You will hear a ratcheting sound when the jaws are closed around the bit and cannot be tightened further.
INSTALLING BITS USING THE KEYLESS See Figures 13- 14. CHUCK [] Lock the switch trigger by placing the direction of rotation selector in the center position. [] Turn the auto lock selector to drill mode. [] Open or close the chuck opening is slightly larger use. Also, raise the front bit from falling out of the [] Insert the drill bit. jaws to a point where the than the bit size you intend to of the drill slightly to keep the chuck jaws. [] Tighten the chuck jaws on the drill bit.
_lk WARNING:Makesurethechuckjawsaresecurely tightenedonthedrillbit beforechangingtheauto lockselectorfromautolockmodeto drillmode. _ WARNING: Be prepared for binding at bit breakthrough. When these situations occur, drill has a tendency to grab and kick opposite to the direction of rotation and could cause loss of control when DRILLING breaking through material. If not prepared, this loss of control can result in possible serious injury. See Figures 15- 16.
_ _ WARNING:Whenservicing,useonlyidentical Craftsman replacement parts.Useofanyotherpart maycreatea hazardor causeproductdamage. GENERALMAINTENANCE Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc. WARNING:Alwayswearsafetygogglesor safety glasseswithsideshieldswhenusingcompressed air to cleantools.
CHUCK REMOVAL Insert the hex key into the chuck and tighten the chuck jaws securely. Tap sharply with a mallet in a counterclockwise direction. This will loosen the chuck on the spindle. It can now be unscrewed by hand. See Figures 17 - 19. The chuck may be removed and replaced by a new one. [] Lock the switch trigger by placing the direction of rotation selector in center position. [] Insert a 5/16 in. or larger hex key into the chuck of the drill and tighten the chuck jaws securely.
.- CRAFTSMAN I 14.4 VOLT CORDLESS DRILL MODEL NO. 315.115470 model_number The will be found on a plate attached to the motor housing. Always mention the model I number in all correspondence regarding your CORDLESS DRILL-DRIVER or when ordering repair parts. SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS 4 PARTS LIST Key No. PaR Number Description 1 6613402 Screw ................................................................................................................
