MANUAL ® ! 1/2 in., 19,2 VOLT CORDLESS DRULL-DRIVER VARIABLE SPEED/REVERSIBLE Model No. 315.115810 •t_ WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before usingthis product. BATTERIES AND CHARGERS SOLD SEPARATELY Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: www.sears.
ONE-YEAR FULL WARRANTY ON CRAFTSMAN TOOL If this Craftsman tool falls to give complete satisfaction within one year from date of purchase, RETURN IT TO ANY SEARS STORE OR OTHER CRAFTSMAN OUTLET IN THE UNITED STATES FOR FREE REPLACEMENT. tf this Craftsman tool is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase, This warranty gives you specific legal rights, and you may also have other rights which vary from state to state, Sears, Roebuck and Co., Dept.
_ WARNING! Read all instructions. Failureto follow all instructions listed below may result fn electric shock, fire and/or serious tnlury_ The term "power toot" in all of the warnings listed below refers to your mains-operated (corded} power too! or battery-operated (cordless) power tool. SAVE THESE INSTRUCTIONS WORK AREA SAFETY [] Keep work area clean and well lit.
1_Usethe power tool, accessoriesand tool bits etco, in accordance with these instructionsand in the manner intendedfor the particulartype of power tool, taking into accountthe working condffions and the work to be performed.Use of the power tool for operations different from those intended could result in a hazardous situation, BATTERY TOOL USE AND CARE Ensure the switch is in the off position before inserting battery pack.
A An extension cord should not be used unless absolutely necessary° Use of improper extension cord could result In a risk of fire and electric shock If extension cord must be used, make sure; WARNING! READAND UNDERSTANDALL INSTRUCTIONS_Failureto follow all instructions listed below, may resultin electric shock, fire and/or serious personal injury, a, That p_nson plug of extension cord are the same number, size and shape as those of p{ug on charger, Before using battery charger, read all instructions and
Some of the following symbols may be used on this tool. Please study them and learn their meaning.. Proper interpretation of these symbols wil! allow you to operate the tool better and safer..
Thefollowing signal wordsandmeanings areintended toexplain thelevels ofriskassociated SYMBOL SIGNAL MEANING A DANGER: Indicates an Imminently hazardous situation, which, tf not avoided, will result in death or serious injury. A A WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result In death or serious Injury. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
PRODUCT SPECIFICATIONS Chuck ........................................................... Motor ............................................................... t/2 in° Keyless Clutch ................................................................... 24 Position 19.2 Volt DC Torque .................................................... Maximum 420 in lb° Switch .............................................................. Variable Speed Charger Input .....................................
KNOW YOUR DRILL-DRIVER See Figure 1.
A ,$L CHARGING A COOL BATTERY PACK WARNING: Do not allow familiarity wffh too_s to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. _fbattery pack is below norton) temperature range, the green LED on charger wil) come on. A_)ow battery pack to reach normal temperature, then the red LED will come on.
CHARGING A HOT BATTERY PACK TO INSTALL When using the toolcontinuously, the batteries in the battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge- When the battery pack becomes discharged and is hot, this will cause the green LED to come on instead of the red LED..
,_ WARNING: Battery tools are always in operating condition° Therefore, switch should always be locked when not in use or carrying at your side° DIRECTION OFROTATION SELECTOR (FORWARD / REVERSE / CENTER REVERSE To stop the ddll, release the switch trigger and allow the chuck to come to a complete stop.
TO DECREASE TORQUE KEYLESS CHUCK See Figure 6, AI)JUSTING FtlHG The drill has a keyless chuck to tighten or release ddl] bits in the chuck jaws.
BIT STORAGE See Figure9. When not in use, bits provided with the drill can be placed in the storage arealocatedon the base of the drill. CHUCK COLLAR SCREWDRIVER BIT LOCI( (TIGHTEN) CHUCK BODY RIGHT Btf STORAGEAREA INSTALLING Fig° 10 Fig,9 BITS See Figures 10 - 11.
ADJUSTING THE AUXILIARY See P3gure I2. HANDLE LEVEL ASSEMBLY m Loosen the auyJliary handle assembly by turning the knob counterdockwise, B Rotate the auxiliary handle assembly to the desired location° u Tighten the auxiliary handle assembly securely by turning the knob c]ockwise_ TORQUE AUXILIARY ADJUSTMENT R|NG HAHDLE ASSEMBLY Fig. 13 360° ROTATIOH m When drilling hard, smooth surfaces, use a center punch to mark the desired hole location.
MALLET ,_ WARNING: When servicing, use only idenfica} Craftsman replacement parts. Use of any other part may create a hazard or cause product damage, ,_ WARNING: A)ways wear sa_e_ygoggles or safety glasses with side shields when using compressed air to ctean tools if the operation is dusty, also wear a dust mask, ._ WARNING: To avoid serious persona! in)ury, aiways remove the battery pack from the tool when cleaning or performing any maintenance. GENERAL Fig.
m Insert the hex key into the chuck and tighten the chuck jaws securely. Tap sharply'_ith a mailer in a counterclockwise direction. This will ioosen the chuck TO RETIGHTEN A LOOSE CHUCK The chuck may become loose on the spindle and deveJop a wobbte Also, the chuck screw may become loose, causing the chuck jaws to bind and prevent them from closing. To tighten: on the spindle° It can now be unscrewed by hand. m Lock the switch trigger by p_acing the direction of rotation selector in the center position.
CRAFTSMAN [ _ 19=2 VOLT CORDLESS DRILL-DRWER MODEL NO. 315.115810 model number will be lound on a plate attached to the motor housing_ Always mention the model I l,number in all correspondence regarding your CORDLESS DRILL-DRIVER or when ordering repair parts, J SEE BACK PAGE FOR PARTS ORDERING i i .... INSTRUCTIONS i -" i i"i!i !:!:i:!............................................................. '.Jj PARTS LIST Key No, Part Number Description t 6613402 Screw (Special)......................
