Owner's Manual 10 in. Stationary TABLE SAW Model No. 315.228390 Save this manual for future reference ^ CAUTION: Read and follow all Safety Rules and Operating instructions before first use of this product. Customer Help Line: 1-800-932-3188 Safety Features Assembly Operation Maintenance Parts List Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: www.sears.
WARRANTY FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAW If this CRRFTSMRN Table Saw fails due to a defeat in material or workmanship within one year from the date of purchase, Sears will repair it, free of charge. Contact a Sears Service Center for repair. If this product is used for commercial or rental purposes, this warranty applies only for 90 days from the date of purchase. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
TABLE OF CONTENTS (CONT.) Mounting the Leg Stand on the Table Saw Base....................................................................................................19 Assembling Table Extensions.................................................................................................................................20 Aligning Table Extensions.......................................................................................................................................
RULES FOR SAFE OPERATION The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. SYMBOL A MEANING SAFETY ALERT SYMBOL Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictographs.
RULES FOR SAFE OPERATION (Continued) ■ DO NOT OVERREACH. Keep proper footing and balance at all times. ■ SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hand and frees both hands to operate tool. ■ USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. Use only a cord heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
RULES FOR SAFE OPERATION (Continued) ■ USE A SUPPORT FOR THE SIDES AND BACK OF THE SAW TABLE when sawing wide or long workpieces. Use a sturdy “outrigger” support if a table extension is more than 24 inches long and is attached to the saw, to prevent tipping. ■ CUT ONLY WOOD, PLASTIC OR WOOD-LIKE MATERIALS. Do not cut metal. ■ NEVER cut more than one piece at a time. DO NOT STACK more than one workpiece on the saw table at a time. ■ DO NOT REMOVE THE SAW'S BLADE GUARDS.
ELECTRICAL EXTENSION CORDS GROUNDING INSTRUCTIONS Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool's plug. When using a power tool at a consid erable distance from the power source, use an extension cord heavy enough to carry the current that the tool will draw. An undersized extension cord will cause a drop in line voltage, resulting in a loss of power and causing the motor to overheat.
GLOSSARY OF TERMS FOR WOODWORKING Anti-Kickback Pawls Toothed safety devices behind the blade designed to stop a workpiece from being kicked back at the operator during a ripping operation. Arbor The shaft on which a blade or cutting tool is mounted. Bevel Cut A cutting operation made with the blade at any angle other than 90° to the saw table. Molding A non-through cut that gives a varied shape to the workpiece and requires a special blade.
UNPACKING Your new table saw has been designed to give you many years of high quality performance. To insure this goal, proper care and treatment is important. Careful treatment begins with removing all parts from the carton and checking them against the list of loose parts. The long box contains the rails. The large box holds all other parts, which are detailed in the Loose Parts List.
LOOSE PARTS LIST C, Belt Guard................................................................. 1 D, Blade Guard Assembly (Hardware Shown Separately).................................. 1 E, Wrench ......................................................................1 R Handwheel (Hardware Shown Separately)............. 2 G. Leg Brace, lower (short).......................................... 2 H. Leg Brace, lower (long)............................................2 I. Leg Brace, upper (short).................
SMALL PARTS LIST Check all loose parts from the box with the list on the previous page, the figures below and on the following page. Small items such as fasteners and end caps are shown in figures 2 b and 2 c. Follow the instructions in the Assembly section to assemble your new saw. F. X. Hardware for Leg Stand, Leveling Feet, and Mounting Saw Base Hardware for Handwheel...................................... 2 screw (#10-24 x 1/2 in.).......................................... 2 Hardware for Leg Stand ...
SMALL PARTS LIST Check all loose parts from the box with the list and figures below and on the previous pages. Small items such as fasteners and end caps are shown in figure 2 c. Follow the instructions in the Assembly section to assemble your new saw. O. Hardware for Rail, Front......................................... 1 square head bolt (5/16-18 x 1 in..)..........................6 Y. Hardware for Blade Guard Bracket and Blade Guard Assembly flat washer (5/16 in.)........................................
TOOLS NEEDED The following tools are needed for assembly and alignment. Note: The five hex keys listed below have been provided with your saw. The remaining tools are typical shop tools and are not included with your saw. SMALL / MEDIUM PHILLIPS SCREWDRIVER NUT DRIVER 8 mm, 10 mm, and 12 mm HEX KEYS (PROVIDED) 2 mm, 3 mm, 4 mm, 5 mm, and 6 mm HAMMER Fig. 3 CRRFTSMRN‘ TABLE SAW 315.
The following labels are found on your saw in the locations shown. Read all warnings and this owner’s manual before using saw. A WARNING •Raised Guard Can Drop on Spinning Blade and B reak, •To reduce The Risk of Injury, Guard IIIuSt be in Place During Use. •Align and Tighten Riving Knife Fasteners Before Use 10 inch Table Saw 3600 R.P.M. 120 VOLTS 60 Hz AC ONLY 13 A Awarning WHEN SERVICING, USE ONLY IDENTICAL CRAFTSMAN REPLACEMENT PARTS. MODEL 315.22S390 MADE IN TAIWAN SEARS, ROEBUCK AND CO.
A WARNING /1 r\ When Mounting an Auxiliary Fence Face, Position Mounting Hardware Beyond Arrow at Right and Left as Indicated. Keep Fasteners Away From Blade. Do Not Lift Saw With Raiis or Extension Tabies. A WARNING A WARNING Debris on rail can misalign the rip fence. Workpiece could bind or suddenly kick back. You could be hit or cut. Clean debris off fence rail before positioning fence. •Attach Blade Guard Assembly Before Operating this Saw H Fig. 4 b 15 CRRFTSMflN‘ TABLE SAW 315.
FEATURES KNOW YOUR TABLE SAW ANTI-KICKBACK PAWLS REAR RAIL BLADE GUARD RIP FENCE TABLE EXTENSION MITER GAGE GROOVE SCALE TABLE EXTENSION FRONT RAIL SWITCH WITH KEY RIP FENCE HANDLE BEVEL LOCK HANDLE Fig. 5 CRRFTSMiir TABLE SAW 315.
FEATURES OVERVIEW The upper portion of the blade projects up through the table, surrounded by an insert called the throat plate. The height of the blade is set with a handwheel on the front of the cabinet. To accommodate wide panels, the tabletop has extensions on each side. Detailed instructions are provided in the Operation section of this manual for the basic cuts: cross cuts, miter cuts, bevel cuts, and compound cuts.
ASSEMBLY Assembly is best done in the area where the saw will be used. When you remove the table saw base, loose parts, and hardware from the packing materials, check all items with the loose parts list and drawing. If you are unsure about the description of any part, refer to the drawing. If any parts are missing, delay assembling until you have obtained the missing part(s). INSTALLING BASE See Figure 6.
ASSEMBLY ASSEMBLING LEG STAND (Continued) L WARNING: Do not lift the saw table without help. The table saw base weighs approximately 95 lbs. Hold it close to your body. Keep your knees bent and lift with your legs, not your back. Ignoring these precautions can result in back injury. ■ Align the two large holes on the brace and the legs. Insert the carriage bolts. Add flat washers and hex nuts and hand tighten. Repeat for the other short upper brace. These are the front and back sets.
ASSEMBLY ASSEMBLING TABLE EXTENSIONS WARNING: Do not lift the saw table without help. Hold it close to your body. Keep your knees bent and lift with your legs, not your back. Ignoring these precautions can result in back injury, See Figure 10. ■ Locate the table extensions and the small hard ware bag with the following: 8 hex bolts (5/16-18 x 1-1/4 in.) 8 hex nuts (5/16-18) 16 flat washers (5/16 in.) ALIGNING TABLE EXTENSIONS See Figure 11. A good alignment allows the rails to slide on easily.
ASSEMBLY Note: The right side of saw is on your right when facing the saw, as if you were in normal operating position. SQUARE HEAD BOLTS INSTALLING THE REAR RAIL See Figures 12- 14. HEX NUT WARNING: Front and rear rails must be installed and carefully aligned to reduce the risk of kickback. Kickback can result in serious injury. ■ From the carton, remove the rear rail pieces and the following hardware: 6 square head bolts (5/16-18 x 1 in.) 6 flat washers (5/16 in.
ASSEMBLY INSTALLING THE FRONT RAIL SQUARE HEAD BOLTS See Figures 15 and 16. ■ Get the front rail pieces, the switch assembly, and the following hardware; 6 square head bolts (5/16-18 x 1 in.) 6 flat washers (5/16 in.) 6 hex nuts (5/16-18) 2 screws (1/4-20 x 3/8 in.) (located on switch plate) 2 square nuts (1/4-20) (located on switch plate) Front rail connector Right and left end caps for front rail 2 screws (#8-32 x 1/2 in.
ASSEMBLY ALIGNING THE RIP FENCE AND FRONT RAIL See Figures 17 and 18. MOUNTING THE MOTOR See Figure 19. The rip fence scale indicator is installed on the right side of the rip fence but can be removed and rein stalled on the left side if needed. If a cutting operation requires placing the rip fence on the left side of the blade, and you find relocating the scale indicator necessary, simply unscrew and re-attach it.
ASSEMBLY INSTALLING THE BELT AND BELT GUARD See Figures 20 and 21. ■ Get the belt, belt guard, 4 flat washers (#10) and 4 small hex nuts (#10-24). ■ Lower the blade by turning the height handwheel. ■ Slip the belt on the saw pulley (inside cabinet). Lift the motor forward and place the belt on the motor pulley. ■ Check that the belt is straight and both pulleys are aligned. If not, adjust the motor on the motor support assembly. Refer to Mounting the Motor. ■ Raise the saw blade all the way up.
ASSEMBLY INSTALLING THE BLADE GUARD See Figures 23 - 25. WARNING: If the blade is not fully lowered, turn the height handwheel to lower the blade to prevent injury. ■ Get the blade guard, the blade guard bracket, and the following hardware: 2 hex bolts (5/16-18 X 1/2 in.) 2 lock washers (5/16 in.) 3 socket head screws (1/4-20 x 3/8 in.) 3 flat washers (1/4 in.) ■ Align the lower end of the blade guard bracket and the threaded holes of the cradle and insert the hex bolts and lock washers.
ASSEMBLY ALIGNING THE RIVING KNIFE WITH THE BLADE See Figures 26 - 28. WARNING: Make sure the switch is off, the switch key is removed, and your saw is unplugged. Failure to do so could result in accidental starting, causing serious personal injury. The riving knife must be aligned with and centered over the blade. WARNING: It is important to install and adjust the riving knife correctly. Poor alignment could cause kickback and throw the workpiece at the operator. ■ Raise the blade guard.
ASSEMBLY FRAMING SQUARE CHECK HEELING (PARALLELING) OF THE SAWBLADE TO THE MITER GAGE GROOVE See Figures 29 - 30. DO NOT loosen any screws until you have checked with a square and made sure adjust ments are necessary. Once the screws are loos ened, these Items must be reset. WARNING: Make sure the switch is off, the switch key is removed, and your saw is un plugged. Failure to do so could result in acciden tal starting, resulting in serious personal injury.
ASSEMBLY MITER GAGE CHECKING RIP FENCE AND BLADE ALIGNMENT See Figures 31-33. The rip fence is self-aligning but should be checked before first use, A WARNING: Fail ure to align the rip fence to the blade can cause jams and kickback, resulting in serious personal injury. ■ Slide the rip fence to the miter gage groove, which is parallel to blade. Do not lock the rip fence, ■ Place a framing square against the rip fence, with the long end towards the front of the blade.
ASSEMBLY CHECKING SQUARENESS OF EXTENSION TABLES TO SAW TABLE See Figure 34. The extension tables should be checked for squarness to the saw table for smooth operation of the rip fence and rails. Place a square on the saw table, with the short end up and check. The long end of the square should extend across one of the extension tables.
ADJUSTMENTS To avoid unnecessary setups and adjustments, a good practice is to check your setups carefully with a framing square and make practice cuts in scrap wood before making finish cuts in good workpieces. Do not start any adjustments until you have checked with a square and made test cuts to be sure adjustments are needed. REPLACING THE BLADE See Figures 35 - 37. WARNING: Make sure the switch is off, the switch key is removed, and your saw is unplugged.
ADJUSTMENTS SCRAP WOOD BLADE GUARD IS NOT SHOWN FOR CLARITY a TO TIGHTEN BLADE NUT HEELING (PARALLELING) THE TO THE MITER GAGE GROOVE See Figures 38 - 40. SAWBLADE DO NOT loosen any screws for this adjustment until you have checked with a square and made test cuts to be sure adjustments are necessary. Once the screws are loosened, these items must be reset. WARNING: Make sure the switch is off, the switch key is removed, and your saw is un plugged.
ADJUSTMENTS ■ If the blade was too close to the miter gage groove, back the bracket away with the block of wood and hammer, SETTING THE BEVEL STOPS AND INDICATOR See Figures 41 and 42. WARNING: Make sure the switch is off, the switch key is removed, and your saw is unplugged. Failure to do so could result in accidental starting, resulting in serious personal injury. ■ Tighten the screws, raise the blade and recheck. ■ Repeat until blade is parallel to miter gage groove.
ADJUSTMENTS Loosen knob and pull out on stop pin to rotate miter gage base past stop screws. Check the 45° setting. Tilt the blade with the bevel handwheel as far as it will go to the left. Place the square against the blade (be sure the square is not against one of the saw teeth). If the blade is not at 45°, unscrew the 45° stop screw (right of blade), turn the handwheel until the blade is correct, and tighten the screw. Recheck and repeat if neces sary.
ADJUSTMENTS REMOVING / REPLACING THE THROAT PLATE See Figure 44. THROAT PLATE WARNING: Make sure the switch is off, the switch key is removed, and your saw is unplugged. Failure to do so could result in accidental starting, resulting in serious personal injury, ■ To remove the throat plate, first loosen the screw in the throat plate with a phillips screwdriver and lift the front end. Pull it out toward the front of the saw. ■ To re-install the throat plate, place it in the opening.
OPERATION ■ To avoid pinching the blade, support the work properly before beginning a cut. BASIC OPERATION OF THE TABLE SAW A table saw can be used for straight-line cutting operations such as cross cutting, ripping, mitering, beveling, and compound cutting. It can make dado or molding cuts with optional accessories. ■ When making a cut, use steady, even pressure. Never force cuts. ■ Do not cut wet or warped lumber.
OPERATION TYPES OF CUTS See Figure 46. There are six basic cuts; 1) the cross cut, 2) the rip cut, 3) the miter cut, 4) the bevel cross cut, 5) the bevel rip cut, and 6) the compound (bevel) miter cut. All other cuts are combinations of these basic six. Operating procedures for making each kind of cut are given later in this section. О Cross Cut WARNING: Always make sure the blade guard and anti-kickback pawls are in place and working properly when making these cuts to avoid possible injury.
OPERATION MAKING A CROSS CUT See Figures 47 and 48. It is recommended that you make test cuts on scrap wood. Stand at the front of the saw and push the wood to the blade with the miter gage. WARNING: Make sure the blade guard is lowered over blade and is working properly to prevent possible injury. ■ Set the blade to the right depth for the workpiece by turning the height handwheel. ■ Set the miter gage to 0°. Make sure miter gage knob is securely tightened.
OPERATION Place a support the same height as the top of the saw table behind the saw for the cut work. Place a support the same height as the top of the saw table behind the saw for the cut work. Position the rip fence the correct distance from the blade for the cut. Make sure the wood is not touching the blade before turning on the saw. Insert the key and lift the switch to the ON position. Let the blade build up to full speed before moving the miter gage to feed the workpiece into the blade.
OPERATION Raise the rip fence handle and remove the rip fence. Set the blade angle by loosening the bevel lock handle and turning the bevel handwheel. Retighten the bevel lock handle. Set the blade angle by loosening the bevel lock handle and turning the bevel handwheel. Retighten the bevel lock handle. ^ WARNING: When making a bevel rip cut, the rip fence must be on the right side of the blade. Otherwise the fence could trap the workpiece, possibly causing kickback and resulting in injury.
OPERATION COMPOUND (BEVEL) MITER CUT MAKING A COMPOUND (BEVEL) MITER CUT See Figure 54. Practice on scrap wood. From the front of the saw, push the wood to the blade with the miter gage. Do not use the rip fence. WHEN MITER GAGE IS ON RIGHT SIDE OF BLADE PLACE LEFT HAND ON WARNING: Make sure the blade guard is lowered over blade and is working properly to prevent possible injury. ■ Set the blade angle and height by loosening the bevel lock handle and turning the height and bevel handwheels.
OPERATION MAKING A LARGE PANEL CUT LARGE PANEL CUT See Figure 55. Make sure the saw is properly secured to a work surface to avoid tipping from the weight of a large panel. WARNING: Make sure the blade guard is lowered over blade and is working properly to prevent possible injury. ■ Place a support the same height as the top of the saw table behind the saw for the cut work. Add supports to the sides as needed. ■ Depending on the shape of the panel, use the rip fence or miter gage.
OPERATION MAKING A DADO CUT DADO CUT See Figure 57. An optional dado throat plate is required for this procedure. See the Accessories section of this manual and check with your nearest Sears Retail Store, All blades and dado sets must be rated at least 5,000 RPM. A WARNING: Unplug the saw before working around the blade. Accidental starting could cause serious injury. ■ Take out the throat plate by loosening the screw. ■ Remove the riving knife and guard assembly. ■ Remove the blade.
MAINTENANCE GENERAL MAINTENANCE MOTOR / ELECTRICAL WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. WARNING: To prevent accidental starting that could cause possible serious personal injury, turn off the saw, remove the switch key, and unplug the saw before working on the table saw. ■ Remove sawdust from the rails, top surface, and inside of saw frequently.
TROUBLESHOOTING PROBLEM CAUSE SOLUTION Saw does not start. 1. Motor cord or wall cord is not plugged in. 1. Plug in motor cord or wall cord. 2. Circuit fuse is blown. 2. Replace circuit fuse. 3. Circuit breaker is tripped. 3. Reset circuit breaker. 4. Cord or switch is damaged. 4. Have the cord or switch re placed at your nearest Sears Service Center. Saw is noisy when running. 1. Motor needs attention. 1. Have the motor checked at your nearest Sears Service Center, Motor is slow or weak.
TROUBLESHOOTING PROBLEM CAUSE SOLUTION Fuses or circuit breakers open frequently. 1. Motor is overloaded. 1. Feed work more slowly. 2. Fuses or circuit breakers are wrong size or defective. 2. Replace fuses or circuit break ers. 3. Dull blade. 3. Replace the blade. 4. Start switch is defective. 4. Have the switch replaced. 1. Blade is warped. 1. Replace the blade. 2. Belt is damaged. 2. Replace the belt. 3. Saw is not mounted securely. 3. Tighten all hardware. 4. Work surface is uneven.
TROUBLESHOOTING PROBLEM CAUSE SOLUTION Rip fence does not move smoothly. 1. Rip fence is not mounted cor rectly. 1. Remove and reposition the rip fence. See Aligning Rip Fence and Front Rail in the Assembly section. 2. Rails are dirty or sticky. 2. Clean and wax the rails. 1. Rip fence is misaligned. 1. See the Assembly section for Checking Rip Fence and Blade Alignment and Aligning Rip Fence and Front Rail procedures. Wood edges away from rip fence when ripping. CRflFTSMftN TABLE SAW 315.
CRfiFTSMBN TABLE SAW 315.
CRBFTSMBr TABLE SAW 315.
CRAFTSMAN TABLE SAW - MODEL NO. 315.228390 The model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. PARTS LIST FOR FIGURE A KEY NO. 1 2 3 4 PART NUMBER DESCRIPTION 982072-001 Miter Gage Knob........................................................................ ........ 1 ** STD551031 982085-001 ** STD511003 QUAN. * Washer (5/16 in.) ...............................................
CRAFTSMAN TABLE SAW - MODEL NO. 315.228390 The model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. PARTS LIST FOR FIGURE B KEY NO. cn PART NUMBER DESCRIPTION 1 979999-001 Leveling Foot............................................................................................................................................................... 4 2 ** STD541031 * Hex Nut (5/16-18).
CRAFTSMAN TABLE SAW - MODEL NO. 315.228390 The model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. PARTS LIST FOR FIGURE C KEY NO. 1 979973-001 2 979945-001 3 cn PART NUMBER ** STD541425 KEY NO. PART NUMBER 14 980964-001 Cam Sleeve ...................... ................. ..............1 .......................... 4 15 980595-001 Pin.......................................
CRAFTSMAN TABLE SAW - MODEL NO. 315.228390 Ul 9 The model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts.
CRAFTSMAN TABLE SAW - MODEL NO. 315.228390 The model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. PARTS LIST FOR FIGURE D cn cn KEY NO. PART NUMBER DESCRIPTION 1 979935-001 Push Nut.............................................................................................................................. ......................................
CRAFTSMAN TABLE SAW - MODEL NO. 315.228390 Ul 9 The model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts.
CRAFTSMAN TABLE SAW - MODEL NO. 315.228390 The model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. PARTS LIST FOR FIGURE E KEY NO. PART NUMBER 1 979945-001 2 cn ** STD512503 DESCRIPTION QUAN. * Screw (#8-32 x 1/2 in.)......................................................................................................... .......................................
CRAFTSMAN TABLE SAW - MODEL NO. 315.228390 The model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. PARTS LIST FOR FIGURE F cn CO KEY NO. PART NUMBER 1 ** STD541010 * Hex Nut (#10).............................................................................................................................................................. 4 2 ** STD551010 * Flat Washer (#10).......
CRAFTSMAN TABLE SAW - MODEL NO. 315.228390 Ul 9 > DO r~ m > C3^ o The model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts.
CRAFTSMAN TABLE SAW - MODEL NO. 315.228390 The model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. PARTS LIST FOR FIGURE G O) KEY NO. PART NUMBER DESCRIPTION 1 979992-002 Base...........................................................................................................................................................................
CRAFTSMAN TABLE SAW - MODEL NO. 315.228390 Ul 9 The model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts.
CRAFTSMAN TABLE SAW - MODEL NO. 315.228390 The model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. PARTS LIST FOR FIGURE H KEY NO.
CRAFTSMAN TABLE SAW - MODEL NO. 315.228390 The model number will be found on a plate attached to the cabinet. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. PARTS LIST FOR FIGURE 1 KEY NO.
(3êî it fixed, at^^y For repair of major brand appliances in your own home... no matter who made it, no matter who sold it! 1-800-4-MY-HOME SM Anytime, day or night {1-800-469-4663) www.sears.com To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Sears Parts & Repair Center. 1 800 488-1222 Anytime, day or night - - www.sears.
