Owner's Manual IPR 0 FES S I 0 NAL i Variable Speed / Reversible PROFESSIONAL 318 in. CORDLESS DRILL-DRIVER Model No. 315.271350 Save this manual for future reference _1=CAUTION: • Safety • Features Read and fellow all Safety Rules and Operating Instructions before first use of this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., Hoffman Estates, IL 60179 Visit the Craftsman web page: www.sears.
• Warranty ......................................................................................................................................................... 2 • Introduction and Product Specifications ......................................................................................................... 2 • Rules For Safe Operation ........................................................................................................................... • A.
The purpose of safety symbols is to attract your attention to possible dangers, The safety symbols, and the explanations with them, deserve your careful attention and understanding, The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures, SYMBOL A MEANING SAFETY ALERT SYMBOL: Indicates warning or caution. May be used in conjunction with other symbols or pictographs.
RULES FOR SAFE OPERATION (Continued) NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite flammable liquids, gases, or fumes. DO NOT PLACE BATTERY TOOLS OR THEIR BATTERIES NEAR FIRE OR HEAT. They may explode. KEEP HANDLES DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products or any strong solvents to clean your tool. DO NOT CHARGE BATTERY TOOL IN A DAMP OR WET LOCATION.
RULES FOR SAFE OPERATION (Continued) An extension cord should not be used unless Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure: a. That pins on plug of extension cord are the same number, size and shape as those of plug on charger. b.
Thefollowingrecommended accessories arecurrentlyavailableatSearsRetailStores. • • • _ 6-Pc.ExtraLengthMagnitePowerBitSet 30-Pc.PowerScrewdriver/Nutdriver SetandCase 17-Pc.PowerScrewdriver/Nutdriver SetandCase WARNING: KNOW YOUR The use of attachments or accessories DRILL-DRIVER • • HighSpeedBits(ForWoodor Metal)..3/4in.Max. KeylessChuck(ItemNo.9-20988) not listed might be hazardous. WRIST STRAP See Figure 1. See Figure 1.
,_ WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. ° ,_ WARNING: Do not allow familiarity with your drill-driver to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. CHARGING YOUR • Normally, the yellow and green lights on charger will come on.
SWITCH TO INSTALL See Figure 2. • Lock switch trigger on your drill by placing the direction of rotation selector in center position. See Figure 2. • Place battery pack in your drill. Align raised rib inside drill with groove on battery pack. See Figure 4. To turn your drill ON, depress the switch trigger. To turn it OFF, release the switch trigger. CENTERPOSITION (LOCK) L I .[ _ BATTERY PACK Fig.
SWITCH LOCK See Figure 5. The switch trigger can be locked in the OFF position. This feature can be used to prevent the possibility of accidental starting when not in use. To lock switch trigger, place the direction of rotation selector in center position. CENTERPOSITION (LOCK) FORWARD REVERSE -7/16 in. BACKSIDEOFCHARGER SELECTOR TRIGGER Fig. 5 ,_ WARNING: Battery tools are always in operating condition. Therefore, switch should always be locked when not in use or carrying at your side.
INSTALLING See Figure 8. REMOVING BITS BITS See Figure 8. • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 2. • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 2. • Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use. Also, raise the front of your drill slightly to k"eep the bit from falling out of the chuck jaws.
Note:Remember thetwo-speed feature(HI-LO)when settingtorque.Theamountoftorquewillvarydependingonwhichspeedsettingyouhaveyourdrill-driver. Switching to LOspeedwillincreasetorque.Switching toHIspeedwilldecreasetorque. DRILLING See Figure 13. BIT STORAGE See Figure 11. When not in use, bits provided with your drill can be placed in the storage area located on the top of your drill as shown in figure 11. SCREWDRIVERBITS BIT STORAGEAREA Fig. 11 Fig.
CHUCK REMOVAL Insert hex key wrench in chuck and tighten chuck jaws securely. Tap sharply with a mallet in a counterclockwise direction, This will loosen chuck on the spindle. It can now be unscrewed by hand. See Figure 16, See Figures 14, 15, and 16. The chuck must be removed in order to use some accessories. To remove: • Lock the switch trigger by placing the direction of rotation selector in center position.
,_ Do not abuse power tools. Abusive practices can damage tool as well as workpiece. WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. Only the parts shown on parts list, page 15, are intended to be repaired or replaced by the customer. All other parts should be replaced by a qualified service technician at an authorized service facility. Avoid using solvents when cleaning plastic parts.
Topreserve naturalresources, please recycle or disposeofproperly. Thisproductcontainsnickelcadmiumbatteries.Local,stateor federallawsmayprohibitdisposalof nickel-cadmium batteriesinordinary trash. Consultyourlocalwasteauthorityforinformation regardingavailablerecyclingand/ordisposaloptions. BATTERY PACK REMOVAL PREPARATION _k 14 AND FOR RECYCLING WARNING: Upon removal, cover the battery pack's terminals with heavy duty adhesive tape.
CRAFTSMAN [ PROFESSIONAL 3/8 in. CORDLESS MODEL NO. 315.271350 DRILL-DRIVER The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your 3/8 in. CORDLESS DRILL-DRIVER or when ordering repair parts. SEE BACK PAGE FOR PARTS ORDERINGINSTRUCTIONS 5 3 PARTS LIST Key No. PaN Number Description 1 616478-0O3 Screw (Special) ............................................. 1 2 973015-001 Chuck (Item No. 9-20988) ........
In U.S.A. or Canada for in-home major brand repair service: Call 24 hours a day, 7 days a week 1-800-4-MY-HOME" Para pedir servicio de reparacibn (1-800-469-4663) a domicilio - 1-800-676-5811 Au Canada pour tout le service ou les pieces - 1-800-469 For the repair or replacement 4663 parts you need: Call 6 a.m - 11 p.m.